BDW13 60 cm Fully integrated full height dishwasher
USER MANUAL FOR YOUR BAUMATIC BDW13 60 cm Fully integrated full height dishwasher NOTE: This User Instruction Manual contains important information, including safety & installation points, which will enable you to get the most out of your appliance. Please keep it in a safe place so that it is easily available for future reference; for you or any person not familiar with the operation of the appliance.
Contents Environmental note 4 Important safety information 5–7 Specifications 8-9 Description of the appliance 9 - 10 Using your dishwasher Before first use Filling with dishwasher salt Setting the water softener level Filling with rinse aid Setting the rinse aid level Filling with dishwasher detergent Loading the upper basket Adjusting the upper basket Loading the lower basket The cutlery basket Loading dishes and cutlery Program table Setting a wash program Changing a wash program At the end of a
ENVIRONMENTAL NOTE Note: Before discarding an old appliance, switch off and disconnect it from the power supply. Cut off and render any plug useless. Cut the cable off directly behind the appliance to prevent misuse. This should be undertaken by a competent person. Disable the door lock to make sure that children cannot get stuck inside the appliance. o The packaging materials that Baumatic uses are environmentally friendly and can be recycled.
IMPORTANT SAFETY INFORMATION Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before attempting to install or use the appliance. If you are unsure of any of the information contained in this booklet, please contact the Baumatic Technical Department. General Safety o Repairs to your appliance must only be carried out by a Baumatic engineer or one of its authorised service agents.
o Care should be taken not to trap the power supply cable underneath the appliance whilst installing it. o No attempt should be made to alter or modify the specifications of this appliance. In daily use o This appliance is only designed to wash normal domestic washloads. If you use your dishwasher in any other way or it is incorrectly used, then Baumatic accepts no liability for any damage that might be caused and any guarantee will be void.
Child Safety o Your dishwasher should only be used by adults. You should not allow children in the area of the machine unsupervised. You should not let them touch the controls or play with the appliance. o It could be possible for a child or pet to gain access to the dishwasher if the door is left open. Therefore please check the inside of the appliance before setting it on a wash cycle. o Any packaging that is removed from the machine should be kept away from children.
Specifications Product dimensions Height: Width: Depth: 820 - 850 mm 595 mm 540 mm Aperture dimensions Height: Width: Depth: 820 mm (min) 600 mm 570 mm (min) Product specifications o 12 Place settings o 7 functions: o o o o o o o o o o o Normal Intensive Economy Rinse Rapid Glass Soak 4 Wash temperatures: 40°C, 45°C, 50°C, 60°C Delay timer LED display Self-cleaning stainless steel micro-filter Anti-leak device Anti-flood device Height adjustable upper basket Collapsible plate racks Adjustable feet Re
Electrical details Rated voltage: 230 Vac 50 Hz Supply connection: 13 A (double pole switched fused outlet with 3 mm contact gap) Optional extra o DWD600SS- Stainless steel door with mark resistant coating Description of the appliance 1) 2) 3) 4) 5) 6) 7) 8) 9) 10) 11) 12) Upper basket Spray arms Lower basket Water softener Main filter Detergent dispenser Cup shelf Cutlery basket Coarse filter Rinse aid dispenser Drain pipe connector Inlet pipe connector 9
Control panel 1) 2) 3) 4) 5) 6) 7) 8) 9) Program indicator neons Program selection button Rinse aid and salt indicator neons ½ load indicator neon ½ load button LED display Delay start button ON/OFF indicator neon ON/OFF button Using your dishwasher Before first use o Install the appliance as per the installation instructions contained within this booklet. o Fill the water softener with 1 litre of tap water and then fill with specialist dishwasher salt. After this you should set the water softener level.
Filling with dishwasher salt IMPORTANT: You should only use salt that is specially designed for use in a dishwasher. If any other type of salt is used in the appliance (in particular table salt), it will damage the water softener. o Ideally you should fill the water softener with salt, just before you are about to run a wash program. This will help to clear any salt that may have overflowed from the water softener during the salt filling process.
o IMPORTANT: You do not need to pour 1 litre of water into the container when you subsequently fill the water softener with salt. Setting the water softener level It is possible to regulate the amount of salt that the water softener will release during a wash cycle. The water softener should be set to a level that is appropriate for the hardness of your water (please refer to the table below).
Filling with rinse aid The rinse aid is released during the final rinse and it helps to prevent water from forming droplets on your dishes. These droplets will lead to spots and streaks being left on items after the wash program has completed. o Your dishwasher is designed to utilise liquid rinse aid. o The rinse aid dispenser is located inside the drop down door, next to the detergent dispenser. o To access the rinse aid dispenser, you should turn the cap anticlockwise and it will pop out of the hole.
o You should continue to adjust the rinse aid level upwards until you get no water spots. o If you get cloudiness or streaking on your dishes, the rinse aid level is set too high and it is causing foaming during the wash cycle. Turn the arrow clockwise and lower the setting to the next number. Filling with dishwasher detergent The detergent dispenser must be refilled at the start of each wash cycle (apart from the Rinse wash program).
Loading the upper basket The upper basket is most suited to washing delicate and light dishware, such as glasses, coffee & tea cups, saucers, plates, bowls and shallow pans (that are not heavily soiled). 1. 2. 3. 4. 5. 6. 7. Cups Small serving bowl Large serving bowl Glasses Saucers Dish Plates o You should position the dishes and cookware in such a way that they are not moved by the spray of water during the wash cycle.
Lower position o If the upper wheels are placed in the guide supports, then the basket is in the lower position. o For accommodating additional tumblers, cups and mugs. You can also place small, espresso sized cups on top of the side racks. You should take care to ensure that there is enough clearance between the top of the cups placed on top of the side racks and the underneath of the dishwasher interior.
IMPORTANT: Care should be taken to make sure that the spray arms can move freely when items have been loaded into the baskets. Loading the lower basket The lower basket is most suited to washing larger and more heavily soiled items, such as saucepans, saucepan lids and serving dishes. You can also load bowls and a variety of plates into the lower basket. 1. 2. 3. 4. 5.
o For the best washing performance, cutlery should be placed through the slots in the top of the cutlery basket. IMPORTANT: Do not allow items of cutlery to fall through the bottom of the cutlery basket, as this may cause damage to the spray arm and/or the cutlery. If the bottom of the basket begins to deteriorate and allows items to fall through, you should replace the cutlery basket.
The following items are NOT suitable for washing inside a dishwasher:o Cutlery with a handle of mother-of-pearl, wood, horn or china. o Plastic items that are not resistant to heat. o Cutlery that consists of glued parts that are not resistant to heat. o Cutlery items or crockery that are bonded. o Copper or pewter items. o Lead crystal glass. o Wooden platters. o Synthetic fibre items.
Program table Program Cycle Program information Normal * For normally soiled loads, such as pots, plates, glasses and lightly soiled pans, standard daily cycle. Intensive For the heaviest soiled loads, such as pots, pans, casserole dishes and dishes that have been sitting with dried food on them for awhile. Economy For lightly soiled loads, such as plates, glasses, bowls and lightly soiled plates.
o Push the top and bottom baskets fully back into position. o Add detergent o Turn the appliance on by using the ON/OFF button. o IMPORTANT: Wait for 5 seconds before pressing the program selection button, otherwise the appliance may not function correctly. o Press the program selection button to choose an appropriate wash program for the load that you are washing. The relevant program indicator neon will light to show which program you have selected. o Select any program options that you want to use (e.g.
At the end of a wash program o The time display will flash for 8 seconds and a buzzer will sound. o If you have used the delay start mode, the time display will flash for 8 seconds but the buzzer will not sound. o Open the door of the appliance. o Use the ON/OFF button to switch the dishwasher off and unload the dishwasher. Setting a delay start It is possible to delay the start of the wash program for up to a maximum of 24 hours. o Check whether the appliance needs rinse aid or salt adding to it.
Setting a half load The half load option means that the lower spray arm does not run. IMPORTANT: You should only load items in the upper basket when using the half load option. o Check whether the appliance needs rinse aid or salt adding to it. o Pull out the top basket, and then load it in accordance with the loading instructions. o Push the top and bottom baskets fully back into position. o Add detergent o Turn the appliance on by using the ON/OFF button.
o The neon indicates that you need to add dishwasher salt to the appliance. You should follow the procedure outlined on page 11. Cleaning and maintenance IMPORTANT: The appliance should be disconnected from your mains supply before commencing any cleaning process. The filter system Your appliance is fitted with three levels of filtering; these are located in the base of the dishwasher for ease of access.
Cleaning the filters For best performance and results, the entire filter assembly should be thoroughly cleaned regularly (ideally after each wash cycle). 1. Turn the coarse filter anti-clockwise and then lift it upwards. Rinse out this section under a tap to remove any food debris that remains in it. 2. Pull out the main filter and rinse this under the tap to remove any food debris that is trapped in it. 3.
Cleaning the spray arms The spray arms should be cleaned regularly, to prevent hard water deposits from clogging the spray arm jets and bearings. o To remove the spray arm, unscrew the nut and take out the washer that sits on top of the spray arm. o Gently pull upwards to remove the spray arm. o Wash the spray arm in warm, soapy water and use a soft brush to clean the jets. o Rinse the spray arm thoroughly and then reassemble the spray arm back in its original position.
Cleaning the door o To clean the edge around the outside of the door, you should use a soft, damp cloth only. o To prevent water from penetrating the door lock or electrical components, DO NOT use a spray cleaner of any kind. o DO NOT use any abrasive cleaner or scouring pads on the inner or outer surfaces, as they may cause damage to them. Error code failure system If your appliance senses that it is not operating correctly, then an error code may appear in the display window.
E3 o Longer heating time- not reaching the required temperature. 9 Malfunction of the temperature sensor or heating element. 9 Call Baumatic Service Department. E4 o The machine has sensed water in the base. 9 Check that the outlet hose is not kinked or crushed. 9 Check that there are no blockages in the drain hose or the drainage system that the appliance is connected to. 9 The drain pipe may be placed in too high a position or incorrectly.
IMPORTANT: If any other fault code appears in the display window, you should not attempt to clear it yourself and contact the Baumatic Service Department. IF THE FAULT CODE REAPPEARS AFTER FOLLOWING THE ABOVE ADVICE AND CLEARING THE FAULT CODE. YOU SHOULD TURN OFF THE APPLIANCE; DISCONNECT THE APPLIANCE FROM YOUR MAINS SUPPLY. THEN ARRANGE FOR AN ENGINEER TO ATTEND THE APPLIANCE. YOU SHOULD CONTACT BAUMATIC SERVICE ON TELEPHONE NUMBER (0118) 933 6911.
Suds in the tub Utensils are not secure in the baskets or something small has dropped into the basket Ensure that everything is loaded as per Baumatic’s loading instructions. Motor hums If the dishwasher is not going to be used for a period of time, then you should make sure that the appliance is set on a wash program once a week. Otherwise the seal around the motor may dry out and cause noise.
Dishwasher leaks The rinse aid dispenser is overfilled or rinse aid has been spilt inside the appliance Take care not to overfill the rinse aid dispenser. Spilt rinse aid could cause oversudsing and lead to overflowing. Wipe away any spills immediately with a damp cloth. Dishwasher isn’t level Make sure that the dishwasher is level. Installation IMPORTANT: THIS INSTALLATION MUST BE COMPLETED BY A SUITABLY QUALIFIED PERSON. BAUMATIC ONLY SANCTION THE INSTALLATION GIVEN IN THIS INSTRUCTION MANUAL.
o The aperture that your dishwasher needs to be installed into should resemble the one shown in the drawing on page 31. o There should be less than a 5 mm gap between the top of the dishwasher and the underneath of the worktop. Installation stages 1. 2. 3. 4. 5. 6. 7. 8. 9. Preparing and connecting the furniture door. Adjusting the tension of the door spring.
o The maximum weight of the furniture door should be 5.5 kilograms. The maximum thickness of the furniture door should be 15 mm. o Use the installation template supplied with the appliance to mark up and then drill out the necessary holes in the furniture door. o Attach the upper hooks onto the furniture door. o Attach the lower hooks onto the furniture door.
Adjusting the tension of the door spring o The door of the dishwasher is attached to springs. These are set at the factory to ensure that they are at the proper tension, so that the door can open and close smoothly. o After the furniture door has been fitted, you will need to adjust the tension of the door spring. o Using an Allen key, rotate the adjusting screw to either tighten or slacken the steel cable.
Connecting to the mains water supply IMPORTANT: Do not connect the appliance to your mains water supply using an old or an existing water inlet hose. The inlet hose supplied with the dishwasher is the ONLY one that should be used. DO NOT CONNECT THE WATER INLET HOSE TO A HOT WATER TAP. o The inlet hose will be located inside the cabinet of the dishwasher. o Connect the water inlet hose (C) to a threaded water tap (A) that has a 3/4” thread and to the inlet hose connector on the appliance.
Connecting to the water outlet 9 Secure the drain hose, so that it cannot move whilst the dishwasher is in use. 9 Place the end of the drain hose on your drain pipe. Push it a short way down into your drain pipe. 9 IMPORTANT: Do not insert the drain hose too deeply into the pipe, as this may cause siphoning. 9 NEVER EXTEND THE DRAINAGE HOSE FROM ITS ORIGINAL LENGTH. Connecting to the power supply 9 IMPORTANT: The electrical socket must still be accessible once the appliance is installed.
9 Consult the rating plate, located on the right hand side of the drop down door BEFORE making the electrical connections. Ensure that the voltage reaching the plug is the same as that on the rating plate. 9 DO NOT REMOVE THE RATING PLATE AS THE INFORMATION ON IT IS IMPORTANT. 9 The moulded plug that is supplied with the appliance must be placed into an earthed and insulated socket. 9 Broken or damaged power leads must only be replaced by a suitably qualified person.
o The condensation strip will be located inside of your dishwasher. o Ensure that the underneath of the worktop is clean before sticking the strip to it. o Separate the backing paper away from the strip. o Stick the condensation strip to the underneath of the worktop. o IMPORTANT: Failure to attach the condensation strip could result in damage to your worktop. Positioning the dishwasher o Place the feet of the dishwasher into the slide rails.
Levelling the appliance o IMPORTANT: Your dishwasher must be level for it to operate properly. o Make sure that the dishwasher is supported whilst it is being levelled, otherwise it may tip over. o The rear feet can be adjusted by using the adjusting screw at the front of the appliance. o The front feet can be adjusted using a spanner. o Use a spirit level to check that the appliance is level. o Check that the appliance is level from side to side. o Check that the appliance is level from front to back.
Securing the dishwasher o The dishwasher must be secured to the worktop, this can be done in one of two ways:o Standard worktop- Secure the dishwasher to the underside of the worktop by using two wood screws. o You should screw through the holes in the brackets at the top of the dishwasher cabinet. o These screws should be fully tightened. o Marble/granite worktop- The material of the worktop will mean that it is impossible to put a screw through the underneath of the worktop.
United Kingdom Baumatic Ltd., Baumatic Buildings, 6 Bennet Road, Reading, Berkshire RG2 0QX United Kingdom Sales Telephone (0118) 933 6900 Sales Fax (0118) 931 0035 Service Telephone (0118) 933 6911 Service Fax (0118) 986 9124 Spares Telephone (01235) 437244 Technical Advice Telephone (0118) 933 6933 E-mail: sales@baumatic.co.uk technical@baumatic.co.uk Website: www.baumatic.co.uk Republic of Ireland 01- 6266 798 Czech Republic Baumatic CR spol s.r.o.