BAUMFOLDER CORPORATION Quality Bindery Equipment Since 1917 714XLT BATCH COUNTER INSTALLATION & PARTS MANUAL ©Baumfolder Corporation, 2000 Printed in U.S.A.
© 2000 Baumfolder Corporation All Rights Reserved WARNING Do not operate this machine without all guarding in place. Do not make adjustments or perform maintenance on this machine with power on. Keep the machine and the work area clean and free of spills to prevent accidents. Be sure to replace any safety decals that may have been detached for any reason.
Contents FUNDAMENTAL SAFETY ............................................................................................................... 4 INSTRUCTIONS ................................................................................................................................ 8 PARTS ................................................................................................................................................
FUNDAMENTAL SAFETY INSTRUCTIONS! The diagrams and descriptions used in these instructions are not necessarily applicable to the specification of the machine supplied. Modifications, made for reasons of technical or operational improvement, are embodied without notice.
FUNDAMENTAL SAFETY INSTRUCTIONS! These operating instructions are designed to familiarize the user with the machine and its designated use. The instruction manual contains important information on how to operate the machine safely, properly and most efficiently. Observing these instructions helps to avoid danger, to reduce repair costs and downtimes and to increase the reliability and life of the machine.
1.1.8 1.3.1.4 Spare parts must comply with the technical requirements specified by the manufacturer. Spare parts from original equipment manufacturers can be relied to do so. Before starting up or setting the machine/plant in motion, make sure that nobody is at risk. 1.3.2 1.1.9 Special work in conjunction with utilization of the machine/plant and maintenance and repairs during operation; disposal of parts and consumables.
1.4.1 Electric energy 1.4.1.1 Use only original fuses with the specified current rating. Switch off the machine/plant immediately if trouble occurs in the electrical system. 1.4.1.2 If provided for in the regulations, the power supply to parts of machines and plants, on which inspection, maintenance and repair work is to be carried out must be cut off.
KIT INSTALLATION CAUTION: BE SURE THE FOLDER IS TURNED OFF AND UNPLUGGED FROM THE AC POWER BEFORE REMOVING ANY GUARDS AND STARTING THE INSTALLATION. 4. Carefully remove the two metric socket head cap screws and mount the vacuum solenoid assembly.(Figure 2) Re-insert and tighten the two metric socket head cap screws.
. Remove the thumb screw on the top section of the mounting post and insert the mounting post on the bottom of the counter fully into the hole. Reinstall and tighten the thumb screw in the top section of the mounting post(Figure 5). 10. Adjust the counter for a comfortable viewing angle and tighten all thumb screws and jam nuts. min=0.125" max=0.250" max=0.250" Figure 3 8. Mount the swivle base to the outside of the side guard using the four screws provided(Figure 4).
3 2 1 Connect the scanner(Figure 6-1) so that the sensor is unobstructed in a cut out(Figure 6-2), between the sheet stop(Figure 6-3) and the nose(Figure 6-4) of the #1 fold pan. 4 Figure 6 OPERATING THE COUNTER SETTING THE BATCH ABOUT THE DISPLAYS Press the + or - buttons to rotate the digits in the thumbwheel The display is a multi function display which is normally used windows to the desired batch amount.
and OFF is in the down position. The connectors for the PHOTO HEAD (scanner) and the BATCHER (Valve, Lift Wheel etc) are locking connectors. They cannot be installed incorrectly. The PHOTO HEAD input is a 4 pin white nylon or 5 pin round male connector and the BATCHER is a 4 pin round black male connector. The current rating of the BATCHER fuse may depend on the type of device supplied. Replace only with the type supplied with the DCU-600.
TP10330 12 DESCRIPTION: BAUMFOLDER CORPORATION UNIT NAME: BATCH COUNTER KIT 714XLT BATCH COUNTER KIT ASSEMBLY NUMBER: 268-322-BG-01 REV: SHEET 1 OF 2
TP10330 CORPORATION BAUMFOLDER UNIT NAME: BATCH COUNTER KIT 714XLT BATCH COUNTER KIT DESCRIPTION: ASSEMBLY NUMBER: 268-322-BG-01 SHEET REV: 2 OF 2
TP10330 14 DESCRIPTION: BAUMFOLDER CORPORATION UNIT NAME: BATCH COUNTER 714XLT BATCH COUNTER KIT ASSEMBLY NUMBER: 268-364-BG-01 REV: SHEET 1 OF 2
TP10330 CORPORATION BAUMFOLDER UNIT NAME: BATCH COUNTER 714XLT BATCH COUNTER KIT DESCRIPTION: ASSEMBLY NUMBER: 268-364-BG-01 SHEET REV: 2 OF 2
Baumfolder has authorized dealers located throughout the United States. Call toll free, 1-800/543-6107 for parts or the number of your nearest authorized dealer. BAUMFOLDER CORPORATION Quality Bindery Equipment Since 1917 1660 Campbell Road Sidney, Ohio 45365-0728 Phone: 937/492-1281 or 800/543-6107 Fax: 800/452-0947 Internet: www.baumfolder.com E-mail: baum@bright.
