Specifications
15
MARINE TUBE SPECIFICATIONS
MBT8014 MBT 1014 MBTA8100 MBTA10100 MBTA8200 MBTA10200
Woofer Size 8 10 8 10 8 10
Voice Coil Size 1.5 high power. /high temp. 1.5 high power. /high temp. 1.5 high power /high temp 1.5 high power. /high temp. 1.5 high power. /high temp. 1.5 high power. /high temp.
Magnet Size 28 oz. 28 oz. 15 oz. 28 oz. 28 oz. 28 oz.
Frequency response* 39-1500 hz. 39-1000 hz. 39-85 hz. 39-85 hz. 39-250 hz. 39-250 hz.
Efficiency** 102 dB* 104 dB* 105 dB* 107 dB* 102 dB* 104 dB*
Power Handling 6-150 watts/channel 6-200 watts/channel 100 watts 100 watts 200 watts 200 watts
Dimensions 18 x 8.5 x 10 20.75 x 10.3 x 12.2 18.125x8.5x10 20.875x10.3x12.2 18.325" x 8.5" x 10" 21.1" x 10.3" x 12.2"
Weight 15.5 lbs. 23 lbs. 14 lbs. 24 lbs. 20 lbs. 25 lbs.
Impedance 4 ohms 4 ohms 2 ohms DVC 2 ohms DVC 4 ohms 4 ohms
* The built in crossover limits the frequency response of the Amplified Bazooka.
** The efficiency levels of all Bazooka subwoofer speaker systems are measured in the typical environment: In the low bass region with one watt of power.
ENGLISH
16
AMPLIFIED MODELS:
(BTA6100, BTA8100, BTA10100, BTA6200, BTA8200, BTA10100,
MBTA8100, MBTA10100, MBTA8200, MBTA10200)
DO NOT substitute the fuse included with the Amplified Bazooka
subwoofer with anything other than the SAME fast blow current
rated fuse. Substitution or deletion will void the product's warranty
and may cause damage to your car or the amplifier.
SHOULD I USE HIGH OR LOW LEVEL INPUTS?
If the source unit has only speaker outputs, use the high-level inputs
of the Amplified Bazooka subwoofer. If the source unit has both high
and low level outputs, we recommend using the high level inputs
over the low level inputs, due to the configuration of the Amplified
Bazooka subwoofer's balanced input circuit. Not all head units, even
those that promise high output voltage in their marketing materials,
indeed have high-voltage RCA outputs. Because of this, Bazooka
Mobile Audio recommends using the speaker level inputs when in
doubtthey will always provide sufficient drive level to the amplifier.
PLEASE NOTE THAT THE WIRING IN A FACTORY STEREO MAY NOT BE
ELECTRICALLY IN PHASE EVEN WHEN YOU HAVE MADE THE PROPER
CONNECTIONS.
Take the time after you make your wire connections to run through
the quick phase check procedure in the AM I IN PHASE? section at
the end of this manual, and NEVER USE BOTH high and low-level
inputs at the same time!
INPUT SIGNAL CONNECTIONS
High-Level Inputs:
If the source unit has both front and rear speaker outputs, use
only one set of speaker outputs for the high-level input of the
Amplified Bazooka. Connect the GREEN wire from the 14-pin
Molex plug of the Amplified Bazooka subwoofer to the source
units left (+) positive speaker output. Connect the GREEN W/BLACK
stripe wire of the plug to the source units left (-) negative speaker
output. Connect the GRAY wire of the plug to the source units
right (+) positive speaker output. Connect the GRAY W/BLACK
stripe wire of the plug to the source units right (-) negative speaker
output. When using high-level inputs, take the time after you
make all wiring connections to run through the AM I IN PHASE
ENGLISH