REVEAL™ 1192 LIFT COFFEE TABLE INSTRUCTION MANUAL LET’S GET STARTED.
Congratulations on the purchase of your Reveal Lift Coffee Table 1192 from BDI. Your coffee table has been designed to provide a lifetime of enjoyment. This manual will provide you with assembly instructions and other helpful information to ensure that you get the most out of your product. Please save it for future reference. Your Reveal Lift Coffee Table has been engineered for simple assembly. Please follow these directions carefully to prevent any damage.
HARDWARE HARDWAREAND ANDCOMPONENTS COMPONENTS Unpack and identify the parts listed below. The assembly workspace should be a non-marring surface such as carpet. For missing hardware pieces, please contact BDI Customer Service at customerservice@bdiusa.com. Do not use power tools for the assembly of this product. For all other concerns, please contact your BDI retailer.
STEP 1. REMOVE CARDBOARD END CAPS ASSEMBLY Making sure the glass tabletop is facing up, remove the cardboard end caps and microfilm. IMPORTANT! Save the end caps. Open the glass lid by lifting and pulling forward. Remove the inner carton. Close the tabletop. 1 C3 2 Place cardboard end caps back onto the ends of the (C3) Cabinet. C3 NEED ASSISTANCE? customerservice@bdiusa.com BDIUSA.
ASSEMBLY STEP 2. ATTACH LEG PLATES Attach two (C1) Leg Plates to the tops of the (C2) Legs using (H1) Screws. Make sure the countersink is facing away from the leg. Tighten with (T1) Hex Wrench. PART/DESCRIPTION QTY T1-HEX WRENCH 1 H1-SCREW 8 H1 C1 H1 C1 C2 H1 H1 C1 C2 6 | BDIUSA.
2 PERSON TASK STEP 3. ATTACH LEGS ASSEMBLY With help from another person, carefully rotate (C3) Cabinet onto its back, making sure that the cardboard end caps stay in place (to prevent the tabletop from opening by itself). Attach both Legs as shown using 16 (H2) Screws. Start all of the (H2) Screws before fully tightening with (T1) Hex Wrench. PART/DESCRIPTION QTY T1-HEX WRENCH 1 H2-SCREW 16 H2 H2 H2 H2 C3 H2 NEED ASSISTANCE? customerservice@bdiusa.com BDIUSA.
2 PERSON TASK FINE TUNING REMOVE END CAPS With help from another person, carefully rotate the (C3) Cabinet onto its base, ensuring that the cardboard endcaps stay in place. Now, remove both of the end caps. C3 Finger slot faces sofa 8 | BDIUSA.
FINE TUNING LIFT & LEVEL TABLE CAUTION! Do not move the table with the tabletop in its extended position. Moving the table by its base is recommended. Position the table approximately 12"–14" away from your sofa with the finger slot facing the opening direction. Using the finger pull located along the tabletop’s underside, pull the tabletop to its fully extended position. If required, use the levelers to make adjustments to the table's base.
CARE & MAINTENANCE GLASS The glass surface is maintained using household glass cleaner and a paper towel or cloth. SATIN-ETCHED GLASS This uniquely smooth-to-the-touch glass surface can be regularly maintained using household glass cleaner and a paper towel or cloth. Minor scratches or scuffs not eliminated using paper towel or cloth can usually be removed by using a ‘Magic Eraser’. Magic Eraser is a melamine foam product available at any grocery store or home improvement center.
WARRANTY BDI warrants to the original purchaser that for the below-stated warranty term, BDI will repair or replace any product, part, or component covered by this warranty that fails under normal use as a result of a defect in material or workmanship. BDI will repair or replace the aforementioned product, part or component with a comparable product, part or component. The decision to repair or replace will be at BDI’s sole discretion.
These distinctive product configurations are protected by US and international patents, trade dress, and/or copyright laws. Reveal & BDI are trademarks of Becker Designed, Inc. All rights reserved. ©2021, BDI | V.08.20.2021 Made in Turkey.