Installation & Assembly

ManualsBrandsBeachcrest Home ManualsCeiling Fans56'' Coso 3 - Blade Propeller Ceiling Fan with Wall Control

Installation Guide

Table of Contents:

Safety Tips. pg. 2

Unpacking Your Fan. pg. 3

Parts Inventory. pg. 3

Installation Preparation. pg. 4

Hanging Bracket Installation. pg. 4

Fan Assembly. pg. 5

Wiring. pg. 6

Canopy Assembly. pg. 7

Blade Assembly. pg. 7

Wall Control Operation. pg. 7

Testing Your Fan. pg. 8

Troubleshooting. pg. 8

Parts Replacement. pg. 8

Warranty. pg. 8

net weight of fan: 11.68 lb (5.3 kg)

READ THESE INSTRUCTIONS AND

AND SAVE THEM FOR FUTURE USE

Utility

page 1

Summary of content (8 pages)

PAGE 1
READ THESE INSTRUCTIONS AND AND SAVE THEM FOR FUTURE USE Utility Installation Guide Table of Contents: Safety Tips. pg. 2 Unpacking Your Fan. pg. 3 Parts Inventory. pg. 3 Installation Preparation. pg. 4 Hanging Bracket Installation. pg. 4 Fan Assembly. pg. 5 Wiring. pg. 6 Canopy Assembly. pg. 7 Blade Assembly. pg. 7 Wall Control Operation. pg. 7 Testing Your Fan. pg. 8 Troubleshooting. pg. 8 Parts Replacement. pg. 8 Warranty. pg. 8 net weight of fan: 11.68 lb (5.
PAGE 2
SAFETY TIPS. WARNING: To reduce the risk of electrical shock, turn off the electricity to the fan at the main fuse box or circuit panel before you begin the fan installation or before servicing the fan or installing accessories. 1. READ ALL INSTRUCTIONS AND SAFETY INFORMATION CAREFULLY BEFORE INSTALLING YOUR FAN AND SAVE THESE INSTRUCTIONS. CAUTION: To avoid personal injury, the use of gloves may be necessary while handling fan parts with sharp edges. 2.
PAGE 3
1. Unpacking Your Fan. Carefully open the packaging. Remove items from Styrofoam inserts. Remove motor housing and place on carpet or Styrofoam to avoid damage to finish. Do not discard fan carton or Styrofoam inserts should this fan need to be returned for repairs. Check against parts inventory that all parts have been included. 2. Parts Inventory. a a. j-hook hanging bracket. 1 piece b. blade. 3 pieces c. motor housing, downrod and canopy (pre-assembled). 1 piece b d. blade arm. 3 pieces d c e.
PAGE 4
12ft. - 20ft. (3.66 m - 6.1m) 3. Installation Preparation. blade edge To prevent personal injury and damage, ensure that the hanging location allows the blades a clearance of 7ft. (2.13m) from the floor and 30in. (76cm) from any wall or obstruction. This fan is suitable for room sizes up to 400 square feet (37.2 square meters). 30 7 feet inches (2.13 m) (76 cm) 12ft. - 20ft. (3.66m - 6.1m) downrod installation This fan can be mounted with a downrod on a regular (no slope) ceiling only.
PAGE 5
. Fan Assembly. Loosen canopy set screw and lower canopy to expose hanging bar. Separate electrical wiring and safety cable from rubber band. Lift fan onto j-hook hanging bracket and slide rubber bushing over hook. Make the wiring connections as shown in Section 6 on the following page. j-hook hanging bracket IMPORTANT: Find a secure attachment point (wood ceiling joist highly recommended) and secure safety cable--refer to diagram on the following page as well.
PAGE 6
wall control wire 6. Wiring. CAUTION: Be sure outlet box is properly grounded and that a ground wire (GREEN or Bare) is present. safety cable black white Make sure all electrical connections comply with Local Codes or Ordinances and the National Electrical Code. If you are unfamiliar with electrical wiring or if the wires in the house/building are different colors than those mentioned below, please consult with a qualified electrician. Connect BLACK wire from fan to BLACK wire from ceiling.
PAGE 7
8. Canopy Assembly. Lift canopy until it covers hanging bracket and touches ceiling. Tighten canopy set screw to secure canopy. canopy canopy set screw 9. Blade Assembly. WARNING: To reduce the risk of serious bodily injury, DO NOT use power tools to assemble the blades. If screws are overtightened, blades may crack and break. Locate 12 blade attachment screws and 12 decorative nuts in hardware packs. Align holes in blade with holes in blade arm. (Note label on blade arm indicating THIS SIDE UP.
PAGE 8
11. Testing Your Fan. Warranty. It is recommended that you test fan before finalizing installation. Restore power from circuit box. Test fan speeds with wall control. Start at the OFF ("0") position (no blade movement) and try each of the 5 different fan speeds.