TDS

ManualsBrandsBEHR PREMIUM ManualsPaint1 gal. White Eggshell Direct to Metal Interior/Exterior Paint

TECHNICAL DATA SHEETTECHNICAL DATA SHEET

INTERIOR/EXTERIOR DIRECTTOMETAL EGGSHELL PAINT

NO. 7200 WHITE

PRODUCT INFORMATION

BEHR PREMIUM® Interior/Exterior Direct-To-Metal Eggshell Paint is engineered for excellent adhesion to a variety of properly

prepared or primed residential and light commercial metal surfaces. It provides a durable nish that withstands tough elements

on both interior and exterior surfaces. It has excellent corrosion and ash rust resistance and is intended for use in conditions

of repeated heavy abrasion, including mechanical wear and repeated scrubbing with industrial solvents, cleaners and scouring

agents. This product can also be used on other properly prepared and primed substrates, such as drywall, wood and masonry.

RECOMMENDED USES:

Ideal for properly prepared coated and uncoated interior & exterior substrates such as:

• Steel • Galvanized Steel • Aluminum • Other Ferrous Metals • Other Non-Ferrous metals

• Drywall/Gypsum Board • Plaster • Stucco • Concrete • Masonry

• Brick • Concrete Masonry Units • Wood • Engineered Wood • Architectural Plastics

PRODUCT SPECIFICATIONS:

Tint Bases/Max Tint Load:

No. 7200 White 124  oz / 6  oz

No. 7230 Deep Base 116  oz / 10  oz

Pre-Mixed colors:

No. 7220 Black

Gloss: 10-20 @ 60°

Resin Type: Styrene Acrylic

Weight per Gallon: 10.5 lb

% Solids by Volume: 35% ± 2%

% Solids by Weight: 48% ± 2%

VOC: <50 g/L

Flash Point: N/A

Viscosity: 95-105 KU

Recommended Film Thickness:

1st Coat Wet: 4.6 mils / Dry: 1.6 mils @ 350 sq ft/gal

2nd Coat Wet: 4.0 mils / Dry: 1.4 mils @ 400 sq ft/gal

Two (2) coats are required for optimum protection and for applications

where this product is used as a self-priming system

Coverage: 350-400 sq ft/gal depending on application

method and substrate porosity. Does not include the loss of

material from spraying.

APPLICATION:

Brush: High Quality Synthetic

Roller: 1/4"- 3/8" nap roller cover, depending on surface

texture

Airless Spray:

Tip: .013"- .017"

Filter: 60 mesh

Fluid Pressure: 1,400 - 2,400 psi

Thinning: DO NOT THIN

Dry Time: @ 77°F & 50% RH

To Touch: 1 hour

To Recoat: 3 hours

Full Cure: 4 weeks

Dry times are temperature, humidity and lm thickness

dependent. Darker colors may require additional dry time

between coats.

SURFACE PREPARATION:

All surfaces must be clean, free of dust, chalk, oil, grease,

wax, polish, mold and mildew stains, loose and peeling

paint, rust and all other foreign substances.

Steel: Minimum surface preparation is Hand Tool Cleaning

in accordance with SSPC-SP2. Remove all oil and grease from

the surface with a solvent in accordance with SSPC-SP1.

For optimal performance, use Commercial Blast Cleaning

in accordance with SSPC-SP6. Prime the area with a rust-

inhibitive primer the same day as cleaned.

Galvanized Steel: Solvent clean new galvanized metal in

accordance with SSPC-SP1 to remove oil and grease from

the surface. Pre-treat with a phosphoric acid solution or

a commercially-available etching solution. Galvanized

metal that has been passivated with chromates or silicates

may require brush blasting in accordance with SSPC-SP16

to remove these treatments. Rusty galvanizing requires a

minimum of Hand Tool Cleaning in accordance with SSPC-

SP2. Prime the area the same day as cleaned.

Shop-Primed Steel: As there is potential for many forms

of contamination during storage and transport, a thorough

cleaning is always recommended for shop-primed surfaces.

Paint exposed areas, i.e., where shop primer is abraded,

with the same material as used for shop priming to comply

with SSPC-PA 1 for touching up shop-primed surfaces. Note:

Assess the integrity of the shop primer prior to application

of subsequent coatings. Review all coatings intended for the

project and conrm the compatibility between shop and

eld-applied coatings.

COMPLIES WITH THE BELOW AS OF 4/1/2023

SCAQMD YES AIM YES

CARB SCM 2007 YES GREENGUARD®

YES

CARB YES LEED® v.4

†

YES

OTC Phase II YES CHPS YES

OTC YES NAHB/ICC NGBS YES

LADCO YES USDA

‡

YES

GREENGUARD is a registered trademark of UL Company.

†

Please visit www.usgbc.org/LEED for additional details.

‡

This coating conforms to United States Department of Agriculture (USDA)

regulatory requirements for incidental food-contact materials intended for use on

surfaces not in direct contact with food, such as walls, oors and ceilings.

Aluminum: Remove all oil and grease from the surface with

a solvent in accordance with SSPC-SP1. Prime the area the

same day as cleaned.

New Drywall: All drywall surfaces should be suciently

sanded smooth. Remove any remaining drywall dust prior to

priming. Allow all drywall compounds to be completely dry

prior to coating.

New Wood: Remove mill glaze with sandpaper or use a

product such as BEHR PREMIUM® All-In-One Wood Cleaner

No. 63 to open the pores of the wood and follow all label

instructions. For severe stains caused by mold, mildew,

algae and fungus, apply a mildew stain removing product.

Set nails and ll holes, scratches, and gouges with the

appropriate wood ller and let dry completely. Remove all

dust with a wiping cloth. Fill all gaps with a 100% acrylic,

siliconized, paintable caulking and allow to dry completely.

Patched and lled surfaces should be sanded smooth

and dusted clean prior to coating. WARNING! Sanding or

scraping pressure treated lumber may be hazardous; wear

appropriate protection.

New Masonry: The pH must be 10 or lower prior to

coating. Smooth masonry may require an adequate prole

for adhesion. For all other smooth trowel concrete, create

an adequate prole for adhesion using a product such as

muriatic acid etcher or with mechanical means. Remove all

loose aggregate and debris. Prime the area with an alkali-

resistant primer.

New Plaster: New plaster should be thoroughly dried out

and cured for a minimum of 30 days before painting. When

cured, clean using a mixed solution of one part vinegar

and one part water to remove eorescence and neutralize.

Prime the area with an alkali-resistant primer.

This information is provided “as is” and no representations or warranties, either express or implied, of merchantability, tness for a particular purpose or of any other

nature are made with respect to this information or to any product referred to in this information. For SDS or to consult with a Behr Paint Company representative,

Revised 4/2023

1 of 3

Summary of content (3 pages)

PAGE 1
TECHNIC AL DATA SHEET INTERIOR/EXTERIOR DIRECT-TO-METAL EGGSHELL PAINT N O. 7200 W H I T E PRODUCT INFORMATION COMPLIES WITH THE BELOW AS OF 4/1/2023 BEHR PREMIUM® Interior/Exterior Direct-To-Metal Eggshell Paint is engineered for excellent adhesion to a variety of properly prepared or primed residential and light commercial metal surfaces. It provides a durable finish that withstands tough elements on both interior and exterior surfaces.
PAGE 2
TECHNIC AL DATA SHEET INTERIOR/EXTERIOR DIRECT-TO-METAL EGGSHELL PAINT N O. 7200 W H I T E Stain-Blocking: After priming, test for stain bleed-through by applying the topcoat to a small section. If the stain bleeds through the topcoat, apply a second coat of primer and test again before topcoating the entire area. If bleeding continues, primer may need a longer dry time before applying topcoat. Previously Painted Surfaces: Remove all loose and peeling paint and all other foreign substances.
PAGE 3
TECHNIC AL DATA SHEET INTERIOR/EXTERIOR DIRECT-TO-METAL EGGSHELL PAINT N O. 7200 W H I T E CAUTIONS/LIMITATIONS: GENERAL INFORMATION: • Protect from freezing. • Do not use on floors. • For best results, apply when air, material and surface temperatures are between 50°F and 90°F, the relative humidity is no greater than 85%, and surface is at least 5°F above dew point. Do not apply in direct sunlight.