TDS

TECHNICAL DATA SHEET
This information is provided "as is" and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For MSDS or to consult with a Behr Certied Coatings Professional,
call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2017 Behr Process Corporation Santa Ana, CA 92704 U.S.A.
Revised 6/2017
1 of 1
1PART EPOXY ACRYLIC CONCRETE & GARAGE FLOOR PAINT
NO. 900
PRODUCT INFORMATION
A high-performance, ready-to-use, single component water-based oor paint that resists hot tire pick-up and marring.
The nish is resistant to household type chemicals, oil and gasoline, which reduces the need for maintenance of hard-to-clean
interior or exterior oors. This durable, satin nish oor paint also resists scung, fading, cracking, peeling and blistering.
RECOMMENDED USES:
Properly prepared interior or exterior surfaces such as:
• Concrete
Ideal for horizontal surfaces such as: Garage Floors, Driveways, Basements and Porches. DO NOT use on vertical surfaces or areas
subject to hydrostatic pressure. NOT for industrial use. DO NOT use on areas subject to fork-lifts.
PRODUCT SPECIFICATIONS:
Tint Bases/Max Tint Load:
No. 900 122 oz. / 8 oz.
No. 930 116 oz. / 14 oz.
Pre-Mixed Colors:
No. 901 Silver Gray
No. 902 Slate Gray
Gloss: 15-25 @ 60°
Sheen: 40-60 @ 85°
Resin Type: Epoxy/Acrylic
Weight per Gallon: 9.7lbs.
% Solids by Volume: 30.0%
% Solids by Weight: 39.7%
VOC: <50 g/L
Flash Point: N/A
Viscosity: 90-100 KU
Recommended Film Thickness:
Wet: 5.3 Dry: 1.6 mils @ 300 Sq. Ft./Gal.
Wet: 3.2 Dry: 1.0 mils @ 500 Sq. Ft./Gal.
Coverage: 300-500 Sq. Ft./Gal. depending on application
method and substrate porosity. Does not include the loss of
material from spraying.
APPLICATION:
Brush: Nylon/polyester
Roller: 3/8"-1/2" nap
Spray: .015"-.019"
Filter: 60 mesh
Thinning: Do Not Thin.
Dry Time: @ 77° & 50% RH
Longer dry time may be required in cooler temperatures
and higher humidity.
To Touch: 1 hour
To Recoat: 4 to 6 hours
Allow surface to dry 24-48 hours before subjecting
painted surface to heavy foot trac.
Allow 7 days before subjecting painted surface to
automobile trac.
SURFACE PREPARATION:
New and Uncoated Concrete or Masonry Surfaces:
New concrete must cure for a minimum of 30 days.
For proper penetration and adhesion of topcoat, use a
product such as a muriatic acid to clean and etch the
surface. Follow all label instructions. Apply a product such
as BEHR PREMIUM® Concrete & Masonry Bonding Primer
No. 880 to increase adhesion of topcoat to the surface.
Follow all label instructions.
Painted, Stained or Sealed Concrete:
Option 1- To completely remove any previous
coating or sealer. Follow all label instructions.
Option 2- To recoat over an existing coating, remove
any loose or peeling paint and scu sand the surface.
Clean previously coated surfaces in sound condition.
Clean and etch any bare concrete area. Follow all label
instructions. Spot prime all bare concrete areas with
a product such as BEHR PREMIUM Concrete & Masonry
Bonding Primer No. 880 to increase adhesion of topcoat
to the surface. Follow all label instructions.
WARNING! If you scrape, sand or remove old paint, you
may release lead dust. LEAD IS TOXIC. Contact the National
Lead Information Center at 1-800-424-LEAD or log on
to www.epa.gov/lead.
CLEAN UP:
Clean all tools and equipment with clean water.
For disposal of empty containers and unused product,
contact your household refuse collection service.
CAUTIONS/LIMITATIONS:
• Protect from freezing.
• For best results, apply at temperatures between
50°F - 90°F. Temperatures above 90°F may aect the
application such as drying too fast. Avoid painting in
direct sun. NOTE: If the surface is hot to the touch it
should be considered too hot to apply this coating.
• Avoid heavy trac for 72 hours.
• DO NOT APPLY MORE THAN TWO COATS
• Allow 30 days before washing or cleaning for full cure.
• Shelf life under normal conditions is two years unopened.
GENERAL INFORMATION:
Warning! Causes eye and skin irritation. Wear protective
clothing, gloves, eye, and face protection. Do not eat, drink,
or smoke when using this product. Take o contaminated
clothing and wash it before reuse. Wash hands thoroughly
after handling. Dispose of unused, contents, container and
other contaminated wastes in accordance with local, state,
federal and provincial regulations.
First aid: If in eyes: Rinse cautiously with water for
several minutes and remove contacts if present and easy
to do. Continue rinsing and get medical attention if eye
irritation persists. If on skin: Wash with plenty of soap
and water. If swallowed: Rinse mouth and get medical
attention if you feel unwell.
COMPLIES WITH THE BELOW AS OF 6/1/2017
SCAQMD YES LEED v.3 (2009)
†
YES
CARB YES LEED v.4
†
YES
OTC YES GREENGUARD® YES
LADCO YES FLAME SPREAD/CLASS A YES
AIM YES
†
Please visit www.usgbc.org/LEED for additional details.
GREENGUARD is a registered trademark of UL Company.