Use and Care Manual

©2020 Behr Process Corporation
Santa Ana, CA 92705 U.S.A. • behr.com
V.O.C. (C.O.V.) <50 g/L • REV. 02/19
No. 900 White Base
No. 901 Silver Gray
No. 902 Slate Gray
No. 930 Deep Base
BEHR PREMIUM Concrete & Garage 1 Part
Epoxy Coating
• Interior/Exterior Satin Finish
• Self-Priming, No-Mix Formula
• Available in Custom Colors
• Resists Hot Tire Pick-Up
• Stain, Chemical & Weather Resistant
CAUTION: Painted surfaces may become slippery when wet. Adding an anti-slip floor additive
may help prevent slipping.
WHERE TO USE
Interior/Exterior surfaces such as: Porous Concrete, Masonry, Stone and Brick. Ideal for
horizontal surfaces such as: Garage Floors, Driveways, Basement Floors, Porches and Pool
Decks. DO NOT use on vertical surfaces or areas subject to hydrostatic pressure. NOT for
industrial use or areas subject to forklifts.
PREPARATION † (Proper Surface Preparation is Required.)
• All surfaces must be clean, sound, dry and free of any dirt, oil and grease.
New and Uncoated Concrete or Masonry Surfaces:
• Allow new surfaces to cure 30 days.
• Clean and etch surface using a product such as a muriatic acid etcher (read and follow
all manufacturer’s label directions) to achieve a textured profile similar to 150 grit
sandpaper.
• Wipe your fingers over the clean, dry floor to check for dust or powder. Ensure there is no
residue on your fingers that may have been left from the etcher. If residue is found,
rinse the surface to remove residue. Allow the surface to dry completely. Sprinkle a few
drops of water onto the surface. If water is quickly absorbed and the surface feels like
150 grit sandpaper, the surface is ready. If not, re-etch.
• Apply a Primer Coat: Apply 1 coat of BEHR PREMIUM Concrete & Garage 1 Part Epoxy
Coating, or a product such as BEHR PREMIUM No. 880 Concrete & Masonry Bonding
Primer to increase adhesion of topcoat to the surface.
Painted, Stained or Sealed Concrete:
• For a painted surface in sound condition, use a product to clean and prepare the surface.
• If the coating is failing or peeling, use a paint stripper to remove old coating or scrape/sand
down to a sound concrete surface.
• Scuff sand glossy surfaces.
• Clean and spot etch any exposed concrete. Remove all dust with a damp cloth, allow to dry.
• Spot prime all bare concrete areas with BEHR PREMIUM Concrete & Garage 1 Part Epoxy
Coating or with a product such as BEHR PREMIUM No. 880 Concrete & Masonry
Bonding Primer to increase adhesion of topcoat to the surface.
APPLICATION
• DO NOT THIN.
• Intermix all cans of same product to ensure color uniformity.
• Stir before and occasionally during application. Use product when air and surface
temperatures are between 50-90° F (10-32° C).
• Apply to dry concrete. Do not apply if rain or heavy dew is expected within 24 hours.
• Apply a thin, even coat using a 3/8” nap roller cover, nylon/polyester brush or an airless
sprayer (.015”-.021” spray tip, 60 mesh filter).
• Allow first coat to dry before deciding if a second coat is necessary.
• For uniformity apply second coat in a criss-cross pattern.
• An annual touch-up may be required in areas subject to tire traffic.
DRY TIME
• Longer dry time required in cooler temperatures and in higher humidity.
• The floor may be subjected to light foot traffic after 24 hours.
• Allow 72 hours before subjecting surface to heavy foot traffic or repositioning furniture.
• Allow 7 days before subjecting to automotive tires.
• Premature heavy traffic will cause paint failure requiring spot recoating.
• If necessary, corrugated cardboard may be used underneath automobile tires after 72 hours.
• Wait at least 30 days before rinsing or cleaning. Use a mild detergent as needed.
• Abrasive cleaners and pressure-washers should be used carefully to avoid premature
paint failure.
DISPOSAL
• Properly dispose of all soiled rags.
• To recycle or properly dispose of product in your community, contact your household
refuse collection service.
LIMITED WARRANTY
Visit behr.com/warranty or call 1-800-854-0133 Ext. 2 for more information.
† WARNING! If you scrape, sand or remove old paint, you may release
lead dust. LEAD IS TOXIC. Contact the National Lead Information Center at
1-800-424-LEAD or log on to www.epa.gov/lead
Spread Rate:
Rough 300-400 Sq. Ft.
Smooth 400-500 Sq. Ft.
Protect
from Freezing
Dry Time:
1 Hr. Dry to Touch.
4-6 Hr. Recoat
Clean-Up:
Soap & Water
WARNING Cancer and Reproductive Harm www.P65Warnings.ca.gov
WARNING! CAUSES EYE AND SKIN IRRITATION. MAY CAUSE RESPIRATORY
TRACT IRRITATION. CONTAINS: CRYSTALLINE SILICA AND TITANIUM DIOXIDE.
Avoid contact with skin and eyes and avoid breathing vapors, spray mist and sanding dust.
Sanding, grinding or abrading may release sanding dust, which may be harmful if inhaled and
has been shown to cause lung damage or cancer with long term exposure. Do not breathe dusts,
vapor, or spray mist. To avoid breathing in dust, vapors, and spray mist, open windows and doors
or use other means to ensure fresh air entry during application, drying, sanding, and/or abrading. If
properly used, a respirator (NIOSH approved with particulate pre-filter) may offer additional protection
and should be used if adequate ventilation cannot be provided; obtain professional advice before
using. If you experience eye watering, headaches, or dizziness during application or drying, increase
fresh air or leave the area. Avoid contact with eyes and skin. Wash thoroughly after handling.
Close container after each use. FIRST AID: If you experience difficulty in breathing, leave the area to
obtain fresh air. If continued difficulty is experience, get medical assistance immediately. In case of
eye contact, flush immediately with plenty of water for at least 20 minutes and get medical attention;
for skin, wash thoroughly with soap and water. If swallowed, get medical attention immediately.
KEEP OUT OF REACH OF CHILDREN – DO NOT TAKE INTERNALLY.