TDS

TECHNICAL DATA SHEET
This information is provided "as is" and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For SDS or to consult with a Behr Certied Coatings Professional,
call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2019 Behr Process Corporation Santa Ana, CA 92705 U.S.A.
Revised 02/2019
PRODUCT INFORMATION
A self-priming high-performance, ready-to-use, single component water-based oor paint that resists hot tire pickup and
marring. The nish is resistant to household type chemicals, oil and gasoline, which reduces the need for maintenance of hard-to-
clean interior or exterior oors. This durable, satin nish oor paint also resists scung, fading, cracking, peeling and blistering.
RECOMMENDED USES:
Properly prepared interior or exterior surfaces such as:
• Concrete
Ideal for horizontal surfaces such as: Garage Floors, Driveways, Basement Floors and Porches. DO NOT use on vertical surfaces or
areas subject to hydrostatic pressure. NOT for industrial use. DO NOT use on areas subject to fork-lifts.
PRODUCT SPECIFICATIONS:
Tint Bases/Max Tint Load:
No. 900 122  oz / 8  oz
No. 116  oz / 14  oz
Pre-Mixed Colors:
No. 901 Silver Gray
No. 902 Slate Gray
Gloss: 5-15 @ 60°
Resin Type: Epoxy/Acrylic
Weight per Gallon: 10.2lbs.
% Solids by Volume: 32% +/- 2%
% Solids by Weight: 45% +/-2%
VOC: <50 g/L
Flash Point: N/A
Viscosity: 75-85 KU (after tinting)
Recommended Film Thickness:
Wet: 5.0 Dry: 1.6 mils @ 300 sq ft/gal
Wet: 3.1 Dry: 1.0mils @ 500 sq ft/gal
Coverage: 300-500 Sq. Ft./Gal. depending on application
method and substrate porosity. Does not include the loss of
material from spraying.
APPLICATION:
Brush: Nylon/polyester
Roller: 3/8"-1/2" nap
Spray: .015"-.021"
Filter: 60 mesh
Thinning: Do Not Thin.
Dry Time: @ 77° & 50% RH
Longer dry time may be required in cooler temperatures
and higher humidity.
To Touch: 1 hour
To Recoat: 4 to 6 hours
The oor may be subjected to light foot trac after
24 hours. Allow surface to dry 72 hours before subjecting
to heavy foot trac or repositioning furniture.
Allow 7 days before subjecting painted surface to
automobile tires.
SURFACE PREPARATION:
New and Uncoated Concrete or Masonry Surfaces:
New concrete must cure for a minimum of 30 days.
For proper penetration and adhesion of topcoat, use a
product such as a muriatic acid to clean and etch the
surface. Follow all label instructions. Apply a Primer
Coat: Apply 1 coat of BEHR PREMIUM® Concrete & Garage
Self-Priming 1-Part Epoxy, or a product such as BEHR
PREMIUM No. 880 Concrete & Masonry Bonding Primer
to increase adhesion of topcoat to the surface. Follow all
label instructions.
Painted, Stained or Sealed Concrete:
Option 1- To completely remove any previous
coating or sealer. Follow all label instructions.
Option 2- To recoat over an existing coating, remove
any loose or peeling paint and scu sand the surface.
Clean previously coated surfaces in sound condition.
Clean and etch any bare concrete area. Follow all label
instructions. Spot prime all bare concrete areas with BEHR
PREMIUM Concrete & Garage Self-Priming 1-Part Epoxy or
with a product such as BEHR PREMIUM No. 880 Concrete &
Masonry Bonding Primer to increase adhesion of topcoat
to the surface.
WARNING! If you scrape, sand or remove old paint, you
may release lead dust. LEAD IS TOXIC. Contact the National
Lead Information Center at 1-800-424-LEAD or log on
to www.epa.gov/lead.
CLEAN UP:
Clean all tools and equipment with clean water.
For disposal of empty containers and unused product,
contact your household refuse collection service.
CAUTIONS/LIMITATIONS:
• Protect from freezing.
• For best results, apply at temperatures between
50°F - 90°F. Temperatures above 90°F may aect the
application such as drying too fast. Avoid painting in
direct sun. NOTE: If the surface is hot to the touch it
should be considered too hot to apply this coating.
• Avoid heavy trac for 72 hours and allow a minimum
of 7 days before subjecting to automotive tires . If
necessary, corrugated cardboard may be used underneath
automobile tires after 72 hours.
• Allow 30 days before washing or cleaning for full cure.
• Shelf life under normal conditions is 2 years unopened.
GENERAL INFORMATION:
CAUTION IRRITANT MAY CAUSE EYE, NOSE AND
THROAT IRRITATION. AVOID CONTACT WITH SKIN AND EYES
AND AVOID BREATHING OF VAPORS AND SPRAY MIST. WEAR
EYE PROTECTION AND PROTECTIVE CLOTHING. USE ONLY WITH
ADEQUATE VENTILATION. To avoid breathing vapors and
spray mist, open windows and doors or use other means to
ensure fresh air entry during application and drying. If you
experience eye watering, headaches or dizziness, increase
fresh air. If properly used, a respirator NIOSH approved for
organic vapor with P series particulate pre-lter) may oer
additional protection; obtain professional advice before
using. A dust mask does not provide protection against
vapors. Avoid contact with eyes and skin. Wash thoroughly
after handling. Close container after each use.
FIRST AID: If you experience diculty in breathing, leave
the area to obtain fresh air. If continued diculty is
experienced, get medical assistance immediately. In case of
eye contact, ush immediately with plenty of water for at
least 20 minutes and get medical attention; for skin, wash
thoroughly with soap and water. If swallowed, get medical
attention immediately.
SELFPRIMING 1PART EPOXY ACRYLIC
CONCRETE & GARAGE FLOOR PAINT
NO. 900
COMPLIES WITH THE BELOW AS OF 2/1/2019
SCAQMD YES LADCO YES
CARB SCM2007 YES AIM YES
CARB YES FLAME SPREAD/CLASS A YES
OTC Phase 2 YES
OTC YES
1 of 1