Use and Care Manual
CAUTION! IRRITANT! HARMFUL IF SWALLOWED. MAY IRRITATE EYES AND
SKIN. Avoid contact with eyes, skin and clothing. Do not breathe fumes. Wear
eye protection and protective clothing. Use only with adequate ventilation. FIRST
AID TREATMENT: Contains ETHYLENE GLYCOL. If swallowed, call a Poison Control
Centre or doctor immediately. Do not induce vomiting. If in eyes rinse with water
for 20 minutes. If on skin rinse well with water. If inhaled, move person to fresh air.
CAUTION: KEEP OUT OF REACH OF CHILDREN - DO NOT TAKE INTERNALLY.
©2016 Behr Process Corporation
Santa Ana, CA 92704 U.S.A. • behr.com
V.O.C. (C.O.V.) <50 g/L • REV. 08/16
No. 900 White Base
No. 901 Silver Gray
No. 902 Slate Gray
No. 930 Deep Base
BEHR PREMIUM
®
1-Part Epoxy
Concrete & Garage Floor Paint
• Interior/Exterior Satin Finish
• Ready-To-Use, No-Mix Formula
• Resists Chemicals & Hot Tire Pick-up
• Slip-Resistant Finish
CAUTION: Painted surfaces may become slippery when wet. Follow all label instructions.
WHERE TO USE
Interior/Exterior surfaces such as: Porous Concrete, Masonry, Stone and Brick.
Ideal for horizontal surfaces such as: Garage Floors, Driveways, Basements, Porches
and Pool Decks. DO NOT use on vertical surfaces or areas subject to hydrostatic
pressure. NOT for industrial use or areas subject to forklifts.
PREPARATION
†
(Proper surface preparation is required.) New and Uncoated Concrete or
Masonry Surfaces: New concrete must cure for a minimum of 30 days.
For proper penetration and adhesion of topcoat, use a product such as
BEHR PREMIUM
®
No. 991 Concrete & Masonry Cleaner & Etcher to clean and
etch the surface. Apply a product such as BEHR PREMIUM No. 880 Concrete
& Masonry Bonding Primer to increase adhesion of topcoat to the surface.
Painted, Stained or Sealed Concrete: Option 1 - To completely strip the entire
surface, use a product such as BEHR PREMIUM No. 992 Concrete & Masonry
Paint Stripper. Option 2 - To recoat over an existing coating, remove any loose or
peeling paint and scuff sand the surface. Use a product such as BEHR PREMIUM
No. 990 Concrete & Masonry Degreaser & Cleaner to clean previously coated
surfaces in sound condition. Use a product such as BEHR PREMIUM No. 991
Concrete & Masonry Cleaner & Etcher to clean and etch any bare concrete area.
Spot prime all bare concrete areas with a product such as BEHR PREMIUM No. 880
Concrete & Masonry Bonding Primer to increase adhesion of topcoat to the surface.
Follow all label instructions.
APPLICATION
DO NOT THIN. Intermix all cans of same product to ensure colour uniformity.
Stir before applying. Use product when air and surface temperatures are between
10-32º C. Apply a thin, even coat using a 10 mm nap roller cover, nylon/polyester
brush or an airless sprayer (.015" - .021" spray tip, 60 mesh filter). Allow first coat
to dry before deciding if a second coat is necessary. For uniformity apply second
coat in a criss-cross direction. An annual touch-up may be required in areas
subject to tire traffic.
DRY TIME
Longer dry time required in cooler temperatures and in higher humidity. The floor
may be subjected to light foot traffic after 24 hours. Allow 72 hours before subjecting
surface to heavy foot traffic or repositioning furniture. Allow 7 days before subjecting
to automotive tires. Premature heavy traffic will cause paint failure requiring spot
recoating. If necessary, corrugated cardboard may be used underneath automobile
tires after 72 hours. Wait at least 30 days before rinsing or cleaning. Use a mild
detergent as needed. Abrasive cleaners and pressure-washers should be used
carefully to avoid premature paint failure.
DISPOSAL
Properly dispose of all soiled rags. To recycle or properly dispose of product in your
community, contact your household refuse collection service.
†
WARNING! If you scrape, sand or remove old paint, you may release lead dust.
LEAD IS TOXIC. Contact the National Lead Information Center at 1-800-424-LEAD
or log on to www.epa.gov/lead
Spread Rate:
Rough 28-37 m
2
Smooth 37-46 m
2
Protect
from Freezing
Dry Time:
1 Hr. Dry to Touch
4-6 Hr. Recoat
Clean-Up:
Soap & Water
LIMITED WARRANTY If this product is found to be defective upon inspection by
an expert, Behr Process Corporation will, at its option, and upon presentation of
proof-of-purchase (the original receipt), either furnish an equivalent amount
of new product or refund the original purchase price of this product to you.
This warranty is not transferable. If you believe this product is defective, contact
Behr Process Corporation at 2750 Centre Avenue N.E., Calgary, AB T2A2L3.
The cost of transportation or shipping, if any, are to be assumed by the consumer.
The clause of limitation of liability which follows is inapplicable in Quebec:
This warranty excludes (1) labour and costs of labour for the application or
removal of any product, and (2) any incidental or consequential damages,
whether based on breach of express or implied warranty, negligence,
strict liability or any other legal theory. The above provisions are not intended to
operate where prohibited by law. This limited warranty is the only warranty provided
by Behr Process Corporation unless extended by a provincial consumer statute.
To consult with a Behr Certified Coatings Professional, call 1-800-661-1591.