TDS
TECHNICAL DATA SHEET
This information is provided "as is" and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For MSDS or to consult with a Behr Certied Coatings Professional,
call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2014 Behr Process Corporation Santa Ana, CA 92704 U.S.A.
Revised 11/2015
1 of 1
WETLOOK SEALER
NO. 985 HIGH GLOSS
PRODUCT INFORMATION
BEHR PREMIUM® Wet-Look Sealer is a clear, non-yellowing, high solids, acrylic-based masonry sealer. It is formulated to seal,
protect and beautify concrete and masonry surfaces with a high gloss, wet-look nish. BEHR PREMIUM Wet-Look Sealer No. 985
is also an excellent topcoat for paints and stains.
RECOMMENDED USES:
Properly prepared or previously coated interior or exterior, vertical or horizontal concrete, stone and tile surfaces, such as:
• Concrete • Concrete Aggregate • Unglazed Tile
• Brick • Natural & Articial Stone • Pavers
• Stucco
PRODUCT SPECIFICATIONS:
Fill Level:
No. 985 Wet Look High Gloss 128 oz.
No. 986 Wet Look Low Lustre 128 oz.
Gloss: 80-90 @ 60°
Resin Type: Acrylic
Weight per Gallon: 8.5 lbs.
% Solids by Volume: 25.4%
% Solids by Weight: 27.6%
VOC: <100 g/L
Flash Point: N/A
Viscosity: 12-24 sec, #2 Zahn Cup
Recommended Film Thickness:
1st Coat Wet: 8.0 Dry: 2.0 mils @ 200 Sq. Ft./Gal.
2nd Coat Wet: 3.5 Dry: 0.9 mils @ 450 Sq. Ft./Gal.
Coverage: 200-450 Sq. Ft./Gal. depending on application
method and substrate porosity. Does not include the loss of
material from spraying.
APPLICATION:
Brush: Nylon/polyester
Roller: 3/8"-1/2" nap
Airless Spray: At packaged consistency
Tip: .015"-.019"
Filter: 60 mesh
Thinning: Do Not Thin
Dry Time: @ 77° & 50% RH
Longer dry time may be required in cooler temperatures
and higher humidity.
To Touch: 1 hour
To Recoat: 4 hours
Allow surface to dry 24-48 hours before subjecting
surface to heavy foot trac.
SURFACE PREPARATION:
Masonry: Concrete, Cut Masonry Units (CMUs),
Split-Faced Block: New and Uncoated: All masonry
surfaces must be cured at least 30 days before painting.
The pH must be 10.0 or lower prior to coating. Smooth
masonry may require an adequate prole for adhesion.
For all other smooth concrete, create a prole using a
product such as a muriatic acid or with mechanical means.
Remove loose aggregate and debris.
WARNING! If you scrape, sand or remove old paint, you
may release lead dust. LEAD IS TOXIC. Contact the National
Lead Information Center at 1-800-424-LEAD or log on
to www.epa.gov/lead.
RECOMMENDED PRIMER/SYSTEMS:
New or uncoated Masonry:
• All surfaces must be clean, free of dust, chalk, oil, grease,
wax, polish, mold and mildew stains, loose and peeling
paint, rust and all other foreign substances.
• BEHR Concrete & Masonry Bonding Primer No. 880
CLEAN UP:
Clean all tools and equipment with clean water.
For disposal of empty containers and unused product,
contact your household refuse collection service.
CAUTIONS/LIMITATIONS:
• Protect from freezing.
• For best results, apply at temperatures between
50°F - 80°F. Temperatures above 90°F may aect the
application such as drying too fast. Avoid painting in direct
sun. NOTE: If the surface is hot to the touch it should be
considered too hot to apply this coating.
• Avoid heavy trac for 24-48 hours.
• Allow 72 hours before repositioning furniture
• Allow two weeks before washing or cleaning for full cure.
• Shelf life under normal conditions is two years unopened.
GENERAL INFORMATION:
Warning Causes eye and skin irritation. Wear protective
clothing, gloves, eye, and face protection. Do not eat, drink
or smoke when using this product. Take o contaminated
clothing and wash it before reuse. Wash hands thoroughly
after handling. Dispose of unused, contents, container and
other contaminated wastes in accordance with local, state,
federal and provincial regulations.
First aid: If in eyes: Rinse cautiously with water for
several minutes and remove contacts if present and
easy to do. Continue rinsing and get medical attention
if eye irritation persists. If on skin: Wash with plenty
of soap and water. If swallowed: Rinse mouth and get
medical attention if you feel unwell.
COMPLIES WITH THE BELOW AS OF 9/1/2014
SCAQMD YES AIM 99
CARB YES LEED v.3 (2009)
†
YES
OTC YES MPI# 99
LADCO YES
†
Please visit www.usgbc.org/LEED for additional details.