User Manual PRO MIXER DX2000USB Professional 7-Channel DJ Mixer with infinium “Contact-Free” VCA Crossfader and USB/Audio Interface
PRO MIXER DX2000USB User Manual Table of Contents Thank you........................................................................ 2 Important Safety Instructions....................................... 3 Legal Disclaimer.............................................................. 3 Limited warranty............................................................. 3 1. Pro Mixer DX2000USB................................................ 4 2. Mono Input Channel................................................
PRO MIXER DX2000USB User Manual Important Safety Instructions Terminals marked with this symbol carry electrical current of sufficient magnitude to constitute risk of electric shock. Use only high-quality professional speaker cables with ¼" TS or twist-locking plugs pre-installed. All other installation or modification should be performed only by qualified personnel.
PRO MIXER DX2000USB User Manual (1) (3) (17) (15) (16) (2) (4) (5) (6) (40) (7) (41) (8) (9) (10) (11) (12) (13) (19) (18) (42) (43) (31) (44) (30) (45) (46) (47) (32) (48) (49) (33) (14) (20) 1. Pro Mixer DX2000USB 1.1 Highly accurate main and PFL peak— reading bargraph meters The main output level is constantly monitored by a pair of highly accurate main bargraph meters (38). In addition, all channels have PFL (Pre-Fader-Listen) (13).
PRO MIXER DX2000USB User Manual 1.6 Packing Your BEHRINGER PRO MIXER DX2000USB was carefully packed in the factory and the packaging was designed to protect the unit from rough handling. Nevertheless, we recommend that you carefully examine the packaging and its contents for any signs of physical damage, which may have occurred in transit.
PRO MIXER DX2000USB User Manual 3.1 Input selection ◊ Normally you will want to PFL only one channel at a time. This might Inputs are on the DX2000USB’s back panel. Your input source is selectable between a pair of stereo inputs by the INPUT switch (1) at the top of the channel strip. An associated pair of LEDs (2) lets you know which input is selected. The choice of inputs depends on which of channels 3 - 7 you are looking at.
PRO MIXER DX2000USB User Manual To set up these controls properly, first turn DAMPING full on (MAX). Set up the gain on your mic channel using PFL. Now adjust SENSITIVITY until the music is always attenuated by a voice signal. (Attenuation is at MAX to enable you to hear this adjustment as clearly as possible.) the X or Y output. In PUNCH mode the X button (34) introduces the X signal to the mix, while the Y button (35) brings in the Y signal.
PRO MIXER DX2000USB User Manual 5.6 Effect return A line-level stereo effect RETURN (54) (Max. gain 30 dB) feeds directly into the mix, level being adjusted by the FX RETURN knob (42). This input is designed to accept the output from a mono or stereo effects unit (see chapter 10 “CONNECTIONS”). It could also be used to return another stereo music source such as DAT or mini disc if five stereo channels are not enough for your music needs. 5.
PRO MIXER DX2000USB User Manual (61) (60) (64) (65) (66) (68) (69) (53) (55) (74) (50) (51) (71) (72) (52) (73) (63) (62) (67) (70) (54) (56) (57) (58) (59) 7. Sub Bass 9. Connections The sub bass output (63) on the back panel comes with two rotary controls, one for output LEVEL (62) (max. +22 dBu) and another for adjusting the crossover frequency of the low pass filter, CROSSOVER FREQUENCY. (61) (low pass filter variable from 30 Hz to 200 Hz).
PRO MIXER DX2000USB User Manual (68) Monitor outputs. Unbalanced ¼" jack, wired tip = signal and sleeve = ground/screen. (69) Zone outputs. Unbalanced ¼" jack, wired tip = signal and sleeve = ground/screen. (70) Monitor outputs. Balanced XLR, wired pin 1 = ground/screen, pin 2 = hot (+ve) and pin 3 = cold (-ve). (72) IEC socket. For connecting the mixer a standard IEC cable. Always connect the mixer to a wall outlet before engaging the POWER switch. (74) USB input.
PRO MIXER DX2000USB User Manual
PRO MIXER DX2000USB User Manual 9.2 Plug soldering guide You will need a lot of cables for different purposes—see the following figures to make sure you have got the right ones. Use custom-made RCA cables for all connections which use RCA sockets (centre post = signal (+ve) and sleeve = ground/screen).
PRO MIXER DX2000USB User Manual 10. Crossfader Adjustment On the main motherboard you can find two potentiometers, which you can adjust with a little screwdriver. These potentiometers are identified as OVERLAP and SLOPE. You can unscrew the bottom of your mixer to reach the main motherboard. ◊ Please be aware that the BEHRINGER warranty becomes discretionary when you start disassembling your DX2000USB! Don’t even think of it, if you make much of your warranty privileges.
PRO MIXER DX2000USB User Manual 11. Specifications Connectors Mono Input Channels Mic Input Electronically balanced, discrete input configuration Gain +10 to +60 dB Frequency response 10 Hz to 80 kHz, +/-3 dB THD 0.08 % typ. @ -30 dBu, 1 kHz Line Input Gain -10 to +40 dB Frequency response 10 Hz to 80 kHz, +/-3 dB THD 0.08 % typ. @ -10 dBu, 1 kHz S/N Ratio 85 dB, unweighted Master Out Jack 0 dB XLR +6 dB Monitor Out Jack 0 dB (max.
PRO MIXER DX2000USB User Manual FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION PRO MIXER DX2000USB Responsible Party Name: MUSIC Group Services US Inc. Address: 18912 North Creek Parkway, Suite 200 Bothell, WA 98011, USA Phone Number: +1 425 672 0816 PRO MIXER DX2000USB complies with the FCC rules as mentioned in the following paragraph: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
We Hear You
