DISHWASHER
Please read this user manual first! Dear Customer, We hope that you get the best results from the product which has been manufactured in state-of-the-art plants and passed through a strict quality control procedure. Therefore, please read the entire user manual carefully before using the product and keep it as a reference for future use. In case of transferring the product to someone else, give the manual as well. The user manual will help you use your product in a fast and safe way.
CONTENTS 1. Dishwasher 3 2. Important safety instructions 5 General safety Intended use Children’s safety 3. Installation 5 5 6 7 Appropriate installation location Connecting water supply Connection to the drain Adjusting the feet Aquasafe+ Electrical connection Initial use Disposing of packaging material Transportation of the product Disposing of the old product 7 7 8 9 9 9 9 10 10 10 4.
1 Dishwasher Overview � �� �� �� � �� � � � � � � � �� 1.Tabletop (depends on the model) 2.Upper impeller 3.Lower basket 4.Lower impeller 5.Filters 6.Control panel 7.Door 8.Detergent dispenser 9.Lower impeller slot 10.Silverware basket 11.Salt reservoir lid 12.Upper basket rail 13.Upper basket with rack 14.
Technical specifications This product complies with the following EU directives: Development, production and sales stages of this product comply with the safety rules included in all pertaining European Community regulations. 2006/95/EC, 2004/108/EC, 93/68/EC, IEC 60436, EN 50242 Power input Total power consumption Heater power consumption Total current Drain pump power consumption Water pressure 220-240 V, 50 Hz 1900-2200 W 1800 W 10 A 30 W 0.3 –10 bar (= 3 – 100 N/cm² = 0.01-1.
2 Important safety instructions This section contains safety instructions that will help to get protected from risk of personal injury or property damage Failure to follow these instructions shall void all warranties. General safety • Never place the product on a • • • • • • • • carpet-covered floor; otherwise, lack of airflow beneath the product will cause electrical parts to overheat. This will cause problems with your product.
• This product should not be used by persons with physical, sensory or mental disorders or unlearned or inexperienced people (including children) unless they are attended by a person who will be responsible for their safety or who will instruct them accordingly for use of the product. Children’s safety • Electrical products are dangerous • • for the children. Keep children away from the product when it is in use. Do not let them to tamper with the product.
3 Installation Refer to the nearest Authorised Service Agent for installation of your product. To make the product ready for use, make sure that the electricity, tap water supply and water drainage systems are appropriate before calling the Authorised Service Agent. If they are not, call a qualified technician and plumber to have any necessary arrangements carried out.
Connection to the drain ��� �� �� � � 1011 �� �� �� ������� �� ��������� �� �� �� ���� �� ���������� ��� Water discharge hose can directly be connected to the drain hole or sink’s drainage. The length of this connection must be min. 50 cm and max. 100 cm from the floor. � �� � � Permitted water temperature: up to 25°C The dishwasher may not be connected to open warm water devices or flowthrough water heaters. Do not use old or used water inlet hose on the new product.
Adjusting the feet If the door of the product cannot be closed properly or if the product swings when you push it slightly, then you need to adjust the feet of the product. Adjust the feet of the product as illustrated in the installation manual supplied with the product. Aquasafe+ (depends on the model) Protect the Aquasafe+ system against water leaks that may occur at hose inlet. Water contact with the valve box of the system must be prevented. Otherwise, electrical assembly will get damaged.
C detergent while the machine is empty. During the initial use, fill the salt reservoir with 1 litre of water prior to filling it with salt. Some water might have remained in the product due to the quality control processes in the production. It is not harmful for the product. Disposing of packaging material materials should not be disposed as normal domestic wastes. Refer to your local dealer or solid waste collection centre in your area to learn how to dispose of your product.
4 Prewashing Tips for energy saving Following information will help you use the product in an ecological and energy-efficient manner. • Wipe away any coarse food remnants on the dishes before putting them in the product. • Operate the product after filling it completely. • When selecting a programme, refer to the "Programme Table". • Do not put more detergent than suggested on the detergent package. Water softening system C The dishwasher requires soft water.
Adding salt Water softening system needs to be regenerated in order for the product operates with the same performance continuously. Dishwasher salt is used for this purpose. C Use in your product only the special softening salts produced particularly for use in dishwashers. C We recommend using granular or powder softening salts. Do not use salts containing insoluble substances such as table salt or common salt in the machine. Performance of water softening system may deteriorate in time.
5. If you will not start a washing programme immediately after adding the salt, run the machine empty in the shortest programme to dissolve and wash away the scattered salt in the machine. C Since different salt brands in the market have different particle sizes and since the water hardness may vary, dissolution of the salt in water may take a couple of hours. Therefore, Salt Indicator remains on for a while after adding salt into the machine.
3. Close the detergent dispenser lid by pressing on it lightly. A "click" will be heard when the lid is closed. C In programmes with prewash and at high temperature, in which you use tablet detergents, make sure that the detergent dispenser lid is closed firmly. C Use powder�detergent in short programmes without prewash since the solubility of the tablet detergent changes depending on the temperature and time.
Rinse aid C The rinse aid used in dishwashers is a special combination used to increase drying efficiency and prevent water or limescale stains on the washed items. For this reason, care must be paid to have rinse aid in the rinse aid reservoir and to use rinse aids produced specially for dishwashers only. Check Rinse Aid Indicator to determine whether it is necessary to add rinse aid or not (3 depends on the model).
time. We strongly recommend you to check if the tableware you are going to purchase is suitable for washing especially in the dishwasher. Placing the dishes into the dishwasher You can use your dishwasher in the optimum way with respect to energy consumption and washing and drying performance only if you place the dishes in an orderly way. • Wipe away any coarse food remnants (bones, seeds, etc.) on the dishes before placing them in the dishwasher.
Suggestions for loading the dishwasher Improper Loading Of Dishware Lower basket Upper basket Improper Loading Of Dishware 17 EN
Silverware basket (depends on the model) Silverware basket is designed to wash your dishes such as fork, spoon and etc. in a cleaner manner. Movable silverware basket (depends on the model) Since the cutlery basket can be moved (A, B), you can create a wider space while placing your dishes to the lower basket and free up space for your dishes in different sizes. 1029_redaksiyon � � 4-3B Tall Tub cutlery basket Silverware basket piece (depends on the model) You can place your forks, spoons and etc.
Collapsable lower basket wires (2 pieces) (depends on the model) The two piece foldable wires located at the lower basket of the machine are designed for an easier placement of large pieces such as pans, bowls, etc. (1, 2). � spaces by folding each wire individually or all of them at once. Lay the foldable wires down by pressing on the latch (A). � � � 1017 � � � � 1054 � You can create larger spaces by folding � each wire individually or all of them at � once.
Lower basket multipurpose / height adjustable service rack � (depends on the model) This accessory located at the lower basket of the machine allows you to easily wash pieces such as extra glasses, long ladles and bread knives. � � � � � � � � To adjust the height of the racks: 1. Fold the rack (E). � � � the rack up (F). 2. Slide � 3. Open the rack at the desired level (G). � � � � 1019 � Make sure that the impeller does not touch the dishes you placed on the racks.
Upper basket drawer (depends on the model) You can easily place additional desert spoons, small forks and knives into the basket drawer installed to the upper basket of your machine. the tab of the glass support piece from the upper basket wire it is hooked to. Thus, you can obtain a wider space.
Collapsable upper basket wires of the loaded basket in up or down directions without removing it from the machine. (depends on the model) To bring the collapsable wires on the upper basket of the machine into horizontal position, press on the latch To raise the basket: 1. Grab one of the upper basket wires (right or left) and lift it up (A). 1021 eps � � (1). Place your larger dishes into the area created (2). To bring the wires back to vertical position, just lift them � up.
2. Repeat the same process to lower the other side of the basket. 3. Make sure that both sides of the basket height adjustment mechanism are at the same level (down or up). To lower the basket: 1. Press the latch on the basket adjustment mechanism (right or left) to lower the basket (B).
Adjusting the height of empty upper basket (depends on the model) You can adjust the height of the upper basket according to the size of the dish to be washed. Use basket rollers to change the basket height. 1. Turn the stoppers on the ends of the upper basket rails by turning them aside (A). 2. Take the basket out (B). 3. Change the position of the rollers, place the basket into the rail and close the stoppers (C).
5 Program Selection and Operating Your Machine � � � 1. 2. 3. 4. � � � � On / Off Button Start/Pause/Cancel Button Display Program Selection Button � 5. 6. 7. � �� � �� 8. 9. 10. 11. Program Indicator Salt Indicator Rinse Aid Indicator Remaining Time Indicator/Delay Time Indicator 12. Start Indicator 13. Delayed Start Indicator �� � Half Load/Tablet Detergent Button Delayed Start Button Handle �� �� � �� 14. Half Load/Tablet Detergent Indicator 15.
Button and Button Descriptions Half Load / Tablet Detergent Button On / Off Button (1) When you press the On/Off button, the display switches on with the last program used and it dims when you turn the machine off. (5) Half Load / Tablet Detergent Button allows you to turn on and off the Half Load and Tablet Detergent functions of your machine.
To use the Half Load and Tablet Detergent functions concurrently, turn on your machine by pressing the On / Off button and then press the Half Load / Tablet Detergent button until Half Load and Tablet Detergent Indicators illuminate together. the estimated remaining time to the end of program. If you have used the Half Load or Tablet Detergent features during the last programme you used, Half Load or the Tablet Detergent function will remain active in the next washing programme you will select.
Programming the Delayed Start Program indicator 15 c lights up when the program is over. Remaining Time Indicator (3) displays “0:00”. Canceling a Program Press Start / Pause / Cancel button (2) for three seconds to cancel a program that is already running. Release the button when symbol (12) start flashing in the display. For a couple of minutes the machine will fulfill the necessary operations required for cancellation. Remaining time indicator (11) displays “0:00”.
If you want to cancel delayed start countdown while it is in progress, then press the Start / Pause / Cancel button (2) for three seconds. Release the button when symbols (12) start flashing in the display. For a couple of minutes the machine will fulfill the necessary operations required for cancellation. Remaining time indicator (11) displays “0:00”. You may select and operate a new program following the delayed start countdown cancellation process.
• Starting Your Machine • Plug the mains plug into the wall • • • • • • • • • • • • socket. Open the tap. Open the door. Place the dishes. Check if the upper and lower impellers rotate freely. Put sufficient amount of detergent in the detergent dispenser and close its lid. Press On/Off button. Check if the salt and rinse aid warning indicators (9,10) light and add salt and/or rinse aid if needed. Determine your washing program with the aid of the Program Data and Table of Average Consumption Values.
31 EN 35°C - 4 60°C Quick & Clean 0,8 4 - Water (I) Energy (kWh) 0,92 10 171 Pre-wash ▼ Wash ▼ Cold rinse ▼ Hot Rinse ▼ Dry ▼ End A+B Medium 1,32 10,2 58 Wash ▼ Cold rinse ▼ Hot Rinse ▼ Dry ▼ End A+B Medium 5 1,26 16,2 143 Pre-wash ▼ Wash ▼ Cold rinse ▼ Hot Rinse ▼ Dry ▼ End A+B High Suitable for heavily soiled dishes, pots and pans.
6 Maintenance and cleaning Service life of the product extends and frequently faced problems decrease if it is cleaned at regular intervals. A Unplug the product and turn off the tap before attempting any cleaning procedures. C Do not use abrasive substances for cleaning. C Clean the filters and impellers at least once a week. 1. Turn the micro filter (3) and coarse filter (2) assembly counter clockwise and pull it out from its seating (A).
3. Press the two pawls on the coarse filter inwards and separate the coarse filter from the assembly (C). � Cleaning the impellers Clean the impellers at least once a week in order for the machine operates efficiently. Lower impeller Check if the holes on the lower impeller (1) are clogged. If they are clogged, remove and clean the impeller. Pull the lower impeller up to remove it (A, B). � � �� 4. Clean all three filters under tap water by means of a brush. 5. Replace the metal/plastic filter. 6.
Upper impeller Check if the holes on the upper impeller (2) are clogged. If they are clogged, remove and clean the impeller. Turn its nut to left to remove the upper impeller (C, D). Make sure that the nut is tightened well when installing the upper impeller.
7 Troubleshooting Machine does not start. • Power cable is unplugged. >>> Check if the power cable is plugged in. • Fuse is blown. >>> Check the fuses in your house. • Water is cut. >>> Make sure that the water inlet tap is open. • Door of the machine is open. >>> Make sure that you have closed the door of the machine. • On / Off button is not pressed. >>> Make sure that you have turned on the machine by pressing the On / Off button.
Dishes are not dry at the end of cycle • Dishes are not placed orderly in the machine. >>> Place your dishes in a way that no water will accumulate in them. • Rinse aid is not sufficient. >>> Check the rinse aid indicator and add rinse aid if necessary. Increase the rinse aid setting if there is enough amount of rinse aid in the machine. • Machine is unloaded right after the programme is over. >>> Do not unload your machine right after washing process is completed.
There is a different odour in the machine C A new machine has a peculiar odour. It will fade out after a couple of washing. • Filters are clogged. >>> Check if the filter system is clean. Clean the filter system regularly as illustrated in section "Cleaning and Care". • Dirty dishes are kept in dishwasher for 2-3 days. >>> If you are not going to start the machine right after you have put the dishes into it, remove the remnants on the dishes and run the Prewash programme without detergent every 2 days.
Detergent remains in detergent dispenser. • Detergent dispenser was damp when adding detergent. >>> Make sure that the detergent dispenser is dried well prior to filling it with detergent. • Detergent is added long before the washing process. >>> Pay attention to add detergent shortly before start-up of the washing. • Opening of the detergent dispenser lid is prevented during washing.
A smear remains on glasses that resembles milk stain which can not be removed when wiped by hand. A bluish / rainbow appearance occurs when the glass is pointed to light. • Excessive rinse aid is used. >>>Lower rinse aid setting. Clean the spilled rinse aid when adding rinse aid. • Corrosion has occurred on glass due to soft water. >>> Measure the hardness of the supply water appropriately and check the water hardness setting. If your supply water is soft (<5 dH), do not use salt.
EN 17 9281 01 00_AG