Enhanced Wireless Router User Manual 8820-00034 F6D4230-4
Table of Contents Table of Contents sections 1 2 3 4 1 Introduction ���������������������������������������������������������������������������������������� 1 5 6 7 8 9 10 Setting WEP Encryption ������������������������������������������������������������������������ 46 Using the Access Point Mode �������������������������������������������������������������� 48 Setting MAC Address Control �������������������������������������������������������������� 49 Configuring the Firewall ���������������
Introduction Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Thank you for purchasing the Belkin Enhanced Wireless Router (the Router). Following are two short sections—the first discusses the benefits of home networking, and the other outlines best practices that maximize your wireless home network range and performance. Please be sure to read through this User Manual completely, and pay special attention to the section entitled “Placement of your Enhanced Wireless Router” on the next page.
Introduction Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Placement of your Enhanced Wireless Router Important Factors for Placement and Setup Your wireless connection will be stronger the closer your computer is to your Router. Typical indoor operating range for wireless devices is between 100 and 200 feet. In the same way, your wireless connection and performance will degrade somewhat as the distance between your Router and connected devices increases.
Introduction Table of Contents sections 1 2 3 4 5 6 7 8 9 3. Cordless Phones 4. Choose the “Quietest” Channel for your Wireless Network If the performance of your wireless network is impaired after attending to the above issues, and you have a cordless phone: In locations where homes or offices are close together, such as apartment buildings or office complexes, there may be wireless networks nearby that can conflict with yours.
Introduction Table of Contents sections 1 2 3 4 5 6 7 8 9 10 5. Secure Connections, VPNs, and AOL Secure connections can be interrupted by a computer’s power management setting, which causes it to “go to sleep.” The simplest solution to avoid this is to simply reconnect by rerunning the VPN or AOL software, or by re-logging into the secure website. Secure connections typically require a user name and password, and are used where security is important.
Product Overview Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Product Features In minutes you will be able to share your Internet connection and network your computers. The following is a list of features that make your new Belkin Enhanced Wireless Router an ideal solution for your home or small office network. Works with Both PCs and Mac® Computers NAT IP Address Sharing The Router supports a variety of networking environments including Mac OS® 8.x, 9.x, X v10.
Product Overview Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Universal Plug and Play (UPnP) Integrated Enhanced Wireless Access Point UPnP is a technology that offers seamless operation of voice messaging, video messaging, games, and other applications that are UPnP-compliant. Enhanced is an exciting new wireless technology that achieves data rates of up to 150Mbps. Actual throughput is typically lower than the connected data rate and will vary depending on your networking environment.
Knowing your Router Table of Contents sections 1 2 3 4 Package Contents • Belkin Enhanced Wireless Router • Quick Installation Guide • Belkin Setup Assistant Software CD • RJ45 Ethernet Networking Cable • Power Supply • User Manual on the Setup Assistant CD 5 6 Broadband Internet connection such as a cable or DSL modem with RJ45 (Ethernet) connection • At least one computer with an installed network interface adapter • TCP/IP networking protocol installed on each computer • RJ45 Et
Knowing your Router Table of Contents sections 1 2 3 4 A. Wireless Security 5 6 7 8 9 10 D. Wired-Computer Status OFF Wireless security is off Off Wired computer is not present Solid Green Wireless security is on Solid Green Wired computer is connected to the Router Blinking Amber Problem with wired computer connecting properly to the Router B. Wi-Fi Protected Setup (WPS) button WPS This button is used for the Wi-Fi Protected Setup feature.
Knowing your Router Table of Contents sections 1 2 3 4 5 6 7 8 9 10 F. Modem Status This icon lights in green to indicate that your modem is connected properly to the Router. It turns amber when problem is detected. OFF Router is NOT connected to modem Solid Green Router is connected to modem and functioning properly Blinking Amber Problem with modem G. Internet Status This unique icon shows you when the Router is connected to the Internet.
Knowing your Router Table of Contents sections 1 2 3 4 5 6 7 8 9 10 H. Connections to Wired Computers – Gray J. Reset Button – Red Connect your wired (non-wireless) computers to these ports. These ports are RJ45, 10/100 auto-negotiation, auto-uplinking ports for standard UTP category 5 or 6 Ethernet cable. The ports are labeled 1 through 4. The “Reset” button is used in rare cases when the Router may function improperly.
Connecting and Configuring your Router sections Table of Contents 1 2 3 4 5 6 7 8 9 10 Verify the contents of your box. You should have the following: Setup Assistant • Belkin Enhanced Wireless Router • RJ45 Ethernet Networking Cable • Power Supply • Belkin Setup Assistant Software CD • User Manual on the Setup Assistant CD Belkin has provided our Setup Assistant software to make installing your Router a simple and easy task.
Connecting and Configuring your Router Table of Contents sections 1 2 3 4 5 6 7 Step 1: Hardware Connections – Follow the Quick Installation Guide (QIG) A WAN B A D LAN C C D D A. Unplug your modem’s power cord. Put the Router next to the modem. Raise the Router’s antenna. B. Locate the networking cable that connects your modem and computer. Unplug that cable from your modem, and plug it into any gray port on the back of the Router. C.
Connecting and Configuring your Router Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Step 2: Set Up the Router – Run the Setup Assistant Software A. Shut down any programs that are running on your computer at this time. Turn off any firewall or Internet-connection-sharing software on your computer. B. Insert the CD into your computer. The Setup Assistant will automatically appear on your computer’s screen within 15 seconds. Click on “Go” to run the Setup Assistant.
Connecting and Configuring your Router Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Confirmation Screen Progress Screen Verify that you have completed all QIG steps by checking the box to the right of the arrow. Click “Next” to continue. Setup Assistant will show you a progress screen each time a step in the setup has been completed.
Connecting and Configuring your Router Table of Contents sections 1 2 3 4 5 6 7 8 9 1.1 Checking Settings 1.2 Verifying Hardware Connections The Setup Assistant will now examine your computer’s network settings and gather information needed to complete the Router’s connection to the Internet. The Setup Assistant will now verify your hardware connection.
Connecting and Configuring your Router Table of Contents sections 1 2 3 4 5 6 7 8 9 10 1.3 Naming your Wireless Network 1.4 Requesting Internet Account Info (if needed) The Setup Assistant will display the default wireless network name or Service Set Identifier (SSID). This is the name of your wireless network to which your computers or devices with wireless network adapters will connect. You can either use the default or change it to something unique.
Connecting and Configuring your Router Table of Contents sections 1 2 3 4 5 6 7 8 9 1.5 Configuring the Router 1.6 Checking Internet Connection The Setup Assistant will now configure your Router by sending data to the Router and restarting it. Wait for the on-screen instructions. We are almost done. The Setup Assistant will now check your connection to the Internet. Note: Do not disconnect any cable or power off the Router while the Router is rebooting.
Connecting and Configuring your Router Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Congratulations Troubleshooting You have finished installing your new Belkin Router. You will see the Congratulations screen when your Router can connect to the Internet. You can begin surfing by opening your browser and going to any website. If the Setup Assistant is not able to connect to the Internet, you will see the following screen.
Connecting and Configuring your Router Table of Contents sections 1 2 3 4 5 6 7 8 9 10 1.7 Optional: Assistance Connecting Other Computers Congratulations This optional step will help you to connect additional wired and wireless computers to your network. Follow the on-screen instructions. Once you have verified that your other wired and wireless computers are properly connected, your network is set up and working. You can now surf the Internet. Click “Next” to take you back to the main menu.
Alternate Setup Method Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Step 1: Hardware Connections – Follow the Quick Installation Guide See the QIG or Step 1: Hardware Connections from the previous section. Step 2: Set your Computer’s Network Settings to Work with a DHCP Server See the section in this User Manual called “Manually Configuring Network Settings” for directions.
Alternate Setup Method Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Logging into the Router Logging out of the Router You will see the Router’s home page in your browser window. The home page is visible to any user who wants to see it. To make any changes to the Router’s settings, you have to log in. Clicking the “Login” button or clicking on any one of the links on the home page will take you to the login screen. The Router ships with no password entered.
Alternate Setup Method Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Understanding the Web-Based Advanced User Interface The home page is the first page you will see when you access the Advanced User Interface (UI). The home page shows you a quick view of the Router’s status and settings. All advanced setup pages can be reached from this page.
Alternate Setup Method Table of Contents sections 1 2 3 4 5 6 7 8 9 10 1. Quick-Navigation Links 4. Login/Logout Button You can go directly to any of the Router’s advanced UI pages by clicking directly on these links. The links are divided into logical categories and grouped by tabs to make finding a particular setting easier to find. Clicking on the purple header of each tab will show you a short description of the tab’s function.
Alternate Setup Method Table of Contents sections 1 2 3 4 5 6 7 8 9 10 6. Language 9. Internet Settings Shows the active language for the Advanced User Interface. Select a desirable language by clicking one of the available languages. Shows the settings of the Internet/WAN side of the Router that connects to the Internet. Changes to any of these settings can be made by clicking on the links or by clicking on the “Internet/WAN” quicknavigation link on the left side of the screen. 7.
Alternate Setup Method Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Step 4: Configuring your Router for Connection to your Internet Service Provider (ISP) The “Internet/WAN” tab is where you will set up your Router to connect to your Internet Service Provider (ISP). The Router is capable of connecting to virtually any ISP’s system provided you have correctly configured the Router’s settings for your ISP’s connection type. Your ISP connection settings are provided to you by your ISP.
Alternate Setup Method Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Setting your Internet Service Provider (ISP) Connection Type to Dynamic IP A dynamic connection type is the most common connection type found with cable modems. Setting the connection type to “dynamic” in many cases is enough to complete the connection to your ISP. Some dynamic connection types may require a host name. You can enter your host name in the space provided if you were assigned one.
Alternate Setup Method Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Setting your Internet Service Provider (ISP) Connection Type to Static IP A static IP address connection type is less common than other connection types. If your ISP uses static IP addressing, you will need your IP address, subnet mask, and ISP gateway address. This information is available from your ISP or on the paperwork that your ISP left with you. Type in your information, then click “Apply Changes” (4).
Alternate Setup Method sections Table of Contents 1 2 3 4 5 6 7 8 9 10 Setting your ISP Connection Type to PPPoE Most DSL providers use PPPoE as the connection type. If you use a DSL modem to connect to the Internet, your ISP may use PPPoE to log you into the service. If you have an Internet connection in your home or small office that doesn’t require a modem, you may also use PPPoE.
Alternate Setup Method Table of Contents 1. sections 1 2 3 4 User Name 5. This space is provided to type in your user name that was assigned by your ISP. 2. Password 7 8 9 10 MTU 6. Disconnect after X... The “Disconnect” feature is used to automatically disconnect the Router from your ISP when there is no activity for a specified period of time.
Alternate Setup Method Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Setting your Internet Service Provider (ISP) Connection Type to Point-to-Point Tunneling Protocol (PPTP) [European Countries Only] Some ISPs require a connection using PPTP protocol, a type of connection most common in European countries. This sets up a direct connection to the ISP’s system. Type in the information provided by your ISP in the space provided. When you have finished, click “Apply Changes” (7).
Alternate Setup Method Table of Contents sections 1 2 3 4 5 6 7 8 9 10 1. PPTP Account 4. Service IP Address Provided by your ISP. Enter your PPTP User ID here. Provided by your ISP. Enter your PPTP gateway/service IP address here. 2. PPTP Password 5. IP Assigned by ISP Type in your password and retype it into the “Retype Password” box to confirm it. If your ISP provided you with a specific IP address, select “Yes” and enter your IP address and subnet mask in the fields that appear. 3.
Alternate Setup Method Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Setting your Internet Service Provider (ISP) Connection Type to Layer 2 Tunneling Protocol (L2TP) [Israel Only]. Some ISPs require a connection using L2TP protocol, a type of connection most common in Israel. This sets up a direct connection to the ISP’s system. Type in the information provided by your ISP in the space provided. When you have finished, click “Apply Changes” (7).
Alternate Setup Method Table of Contents sections 1 2 3 4 Setting your Connection Type if You Are a Telstra® BigPond/ OptusNet Cable User [Australia Only] 5 6 7 8 9 10 Setting Custom Domain Name Server (DNS) Settings A “Domain Name Server” is a server located on the Internet that translates Universal Resource Locators (URLs) like “www.belkin.com” into IP addresses. Many Internet Service Providers (ISPs) do not require you to enter this information into the Router.
Alternate Setup Method Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Configuring your WAN Media Access Controller (MAC) Address Entering a Specific MAC Address All network components including cards, adapters, and routers, have a unique “serial number” called a MAC address. Your Internet Service Provider (ISP) may record the MAC address of your computer’s adapter and only let that particular computer connect to the Internet service.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 7 8 9 10 Viewing the LAN Settings Using your Internet browser, you can access the Router’s Web-Based Advanced User Interface. In your browser, type “192.168.2.1” (do not type in anything else such as “http://” or “www”) then press the “Enter” key. Clicking on the header of the “LAN Setup” tab (1) will take you its header page. A quick description of the functions can be found here.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Changing LAN Settings All settings for the internal LAN setup of the Router can be viewed and changed here. 1. IP Address The “IP address” is the internal IP address of the Router. The default IP address is “192.168.2.1”. To access the advanced setup interface, type this IP address into the address bar of your browser. This address can be changed if needed.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 3. DHCP Server 5. Lease Time The DHCP server function makes setting up a network very easy by assigning IP addresses to each computer on the network automatically. The default setting is “On”. The DHCP server can be turned OFF if necessary; however, in order to do so you must manually set a static IP address for each computer on your network.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Viewing the DHCP Client List Page You can view a list of the computers (known as clients), which are connected to your network. You are able to view the IP address (1) of the computer, the host name (2) (if the computer has been assigned one), and the MAC address (3) of the computer’s network interface card (NIC). Pressing the “Refresh” (4) button will update the list.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Configuring the Wireless Network Settings The “Wireless” tab lets you make changes to the wireless network settings. From this tab you can make changes to the wireless network name or Service Set Identifier (SSID), operating channel, encryption security settings, and configure the Router to be used as an access point.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Changing the Wireless Channel 2) 802.11g only There are a number of operating channels from which you can choose— in the United States, there are 11 and in the United Kingdom (and most of Europe), there are 13. In a small number of other countries, there are other channel requirements. Your Router is configured to operate on the proper channels for the country in which you reside.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Using the Broadcast SSID Feature 1) 20MHz only Note: This advanced feature should be employed by advanced users only. For security, you can choose not to broadcast your network’s SSID. Doing so will keep your network name hidden from computers that are scanning for the presence of wireless networks.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Changing the Wireless Security Settings Using Wi-Fi Protected Setup Your Enhanced Wireless Router is equipped with the latest security standard called Wi-Fi Protected Access™ 2 (WPA2™) and the legacy security standard called Wired Equivalent Privacy (WEP). Your Router also supports the Wi-Fi Protected Setup™ (WPS) specification, which simplifies the setup of a wireless network.
Using the Web-Based Advanced User Interface Table of Contents Enhanced Wireless Router sections 1 2 3 4 43 5 6 7 8 9 10 1. Wi-Fi Protected Setup (WPS): Enabled or Disabled. 2. Personal Identification Number (PIN) Method: In this method, a wireless client wishing to access your network must supply a 4- or 8-digit PIN to the Router. After clicking “Enroll”, you must start the WPS handshaking procedure from the client within two minutes. 3.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 WPA2 Requirements IMPORTANT: In order to use WPA2 security, all your computers and wireless client adapters must be upgraded with patches, driver, and client utility software that supported WPA2. At the time of this User Manual’s publication, a couple security patches are available, for free download, from Microsoft®. These patches work only with the Windows XP operating system.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Setting WPA/WPA2-Personal (PSK) Like WPA security, WPA2 is available in both WPA2-Personal (PSK) mode and WPA2-Enterprise (RADIUS) mode. Typically, WPA2-Personal (PSK) is the mode that will be used in a home environment, while WPA2-Enterprise (RADIUS) is implemented in a business environment where an external radius server distributes the network key to the clients automatically.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Setting WEP Encryption Note to Mac users: The “Passphrase” option will not operate with Apple® AirPort®. To configure encryption for your Mac computer, set the encryption using the manual method described in the next section. 1. Select “128-bit WEP” or “64-bit WEP” from the drop-down menu. 2.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Using a Hexadecimal Key A hexadecimal key is a mixture of numbers and letters from A–F and 0–9. 64-bit keys are 10 digits long and can be divided into five two-digit numbers. 128-bit keys are 26 digits long and can be divided into 13 two-digit numbers. Note to Mac users: Original Apple AirPort products support 64-bit encryption only. Apple AirPort 2 products can support 64-bit or 128-bit encryption.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Using the Access Point Mode Note: This advanced feature should be employed by advanced users only. The Router can be configured to work as a wireless network access point. Using this mode will defeat the NAT IP sharing feature and DHCP server. In AP mode, the Router will need to be configured with an IP address that is in the same subnet as the rest of the network that you will bridge to.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Setting MAC Address Control The MAC address filter is a powerful security feature that allows you to specify which computers are allowed on the wireless network. Note: This list applies only to wireless computers. This list can be configured so any computer attempting to access the wireless network that is not specified in the filter list will be denied access.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Setting up a Deny Access List The “Deny Access” list lets you specify computers that you DO NOT want to access the network. Any computer in the list will not be allowed access to the wireless network. All others will. 1. Select the “Deny” radio button (2) to begin setting up a list of computers to be denied access to the wireless network. 2.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 Configuring the Firewall IP Spoofing • Land Attack Ping of Death (PoD) • Denial of Service (DoS) • IP with zero length • Smurf Attack • TCP Null Scan • SYN flood • UDP flooding • Tear Drop Attack • ICMP defect • RIP defect • Fragment flooding Enhanced Wireless Router 6 7 8 9 10 The firewall also masks common ports that are frequently used to attack networks.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Configuring Internal Forwarding Settings Choosing an Application The Virtual Servers function will allow you to route external (Internet) calls for services such as a web server (port 80), FTP server (Port 21), or other applications through your Router to your internal network.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Setting Client IP Filters The Router can be configured to restrict access to the Internet, email, or other network services at specific days and times. Restriction can be set for a single computer, a range of computers, or multiple computers. To restrict Internet access to a single computer for example, enter the IP address of the computer you wish to restrict access to in the IP fields (1).
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Enabling the Demilitarized Zone (DMZ) The DMZ feature allows you to specify one computer on your network to be placed outside of the firewall. This may be necessary if the firewall is causing problems with an application such as a game or video conferencing application. Use this feature on a temporary basis. The computer in the DMZ is NOT protected from hacker attacks.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Using Dynamic DNS The Dynamic DNS service allows you to alias a dynamic IP address to a static host name in any of the many domains DynDNS.org offers, allowing your network computers to be more easily accessed from various locations on the Internet. DynDNS.org provides this service, for up to five host names, free to the Internet community.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 6 7 8 9 10 Utilities Blocking an ICMP Ping Computer hackers use what is known as “pinging” to find potential victims on the Internet. By pinging a specific IP address and receiving a response from the IP address, a hacker can determine that something of interest might be there. The Router can be set up so it will not respond to an ICMP ping from the outside. This heightens your Router’s security level.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Restarting the Router Sometimes it may be necessary to restart or reboot the Router if it begins working improperly. Restarting or rebooting the Router will NOT delete any of your configuration settings. Restarting the Router to Restore Normal Operation 1. Click the “Restart Router” button. 2. The following message will appear. Click “OK”. Enhanced Wireless Router 57 3.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Restoring Factory Default Settings Using this option will restore all of the settings in the Router to the factory (default) settings. It is recommended that you back up your settings before you restore all of the defaults. 1. Click the “Restore Defaults” button. 2. Enhanced Wireless Router The following message will appear. Click “OK”. 58 3. The following message will appear.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 Saving a Current Configuration You can save your current configuration by using this feature. Saving your configuration will allow you to restore it later if your settings are lost or changed. It is recommended that you back up your current configuration before performing a firmware update. Enhanced Wireless Router 1. 59 Click “Save”. A window called “File Download” will open. Click “Save”.
Using the Web-Based Advanced User Interface Table of Contents 2. sections 1 2 3 4 3. A window will open that allows you to select the location where you want to save the configuration file. Select a location. You can name the file anything you want, or use the default name “user.conf”. Be sure to name the file so you can locate it yourself later. When you have selected the location and name of the file, click “Save”.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Restoring a Previous Configuration This option will allow you to restore a previously saved configuration. Enhanced Wireless Router 1. 61 Click “Browse”. A window will open that allows you to select the location of the configuration file. All configuration files end with a “.conf”. Locate the configuration file you want to restore and double-click on it.
Using the Web-Based Advanced User Interface Table of Contents sections 2. You will be asked if you want to continue. Click “OK”. 3. A reminder window will appear. It will take up to 60 seconds for the configuration restoration to complete. Click “OK”. Enhanced Wireless Router 1 2 3 4 5 4. 62 6 7 8 9 10 A 60-second countdown will appear on the screen. When the countdown reaches zero, the Router’s configuration will be restored. The Router’s home page should appear automatically.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Updating the Firmware From time to time, Belkin may release new versions of the Router’s firmware. Firmware updates contain feature improvements and fixes to problems that may have existed. When Belkin releases new firmware, you can download the firmware from the Belkin update website and update your Router’s firmware to the latest version.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 1. To download the new version of firmware, click “Download”. 2. A window will open that allows you to select the location where you want to save the firmware file. Select a location. You can name the file anything you want, or use the default name. Be sure to locate the file in a place where you can locate it yourself later. When you have selected the location, click “Save”. 4 5 3.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Updating the Router’s Firmware 1. In the “Firmware Update” page, click “Browse”. A window will open that allows you to select the location of the firmware update file. Enhanced Wireless Router 2. 65 Browse to the firmware file you downloaded. Select the file by double-clicking on the file name.
Using the Web-Based Advanced User Interface Table of Contents 3. sections 1 2 3 4 The “Update Firmware” box will now display the location and name of the firmware file you just selected. Click “Update”. 4. Enhanced Wireless Router You will be asked if you are sure you want to continue. Click “OK”. 66 5 6 7 8 9 10 5. You will see one more message.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Changing System Settings Changing the Login Time-Out Setting The “System Settings” page is where you can enter a new administrator password, set the time zone, enable remote management, and turn on and off the NAT function of the Router. The login time-out option allows you to set the period of time that you can be logged into the Router’s advanced setup interface.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Setting the Time and Time Zone Enabling Remote Management The Router keeps time by connecting to a Simple Network Time Protocol (SNTP) server. This allows the Router to synchronize the system clock to the global Internet. The synchronized clock in the Router is used to record the security log and control client filtering. Select the time zone that you reside in.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Enabling/Disabling UPnP Enabling/Disabling Auto Firmware Update UPnP (Universal Plug-and-Play) is yet another advanced feature offered by your Belkin Router. It is a technology that offers seamless operation of voice messaging, video messaging, games, and other applications that are UPnP-compliant. Some applications require the Router’s firewall to be configured in a specific way to operate properly.
Manually Configuring Network Settings Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Set up the computer that is connected to the cable or DSL modem FIRST using these steps. You can also use these steps to add computers to your Router after the Router has been set up to connect to the Internet. Manually Configuring Network Settings in Mac OS up to 9.x In order for your computer to properly communicate with your Router, you will need to change your Mac computer’s TCP/IP settings to DHCP. 1.
Manually Configuring Network Settings Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Manually Configuring Network Settings in Mac OS X 1. Click on the “System Preferences” icon. (1) (2) (4) 2. (3) Select “Network” from the “System Preferences” menu. Enhanced Wireless Router 71 3. Select “Built-in Ethernet” (1) next to “Show” in the “Network” menu. 4. Select the “TCP/IP” tab (2). Next to “Configure:” (3), you should see “Manually” or “Using DHCP”.
Manually Configuring Network Settings Table of Contents 5. 6. sections 1 2 3 4 If “Manually” is selected, your Router will need to be set up for a static IP connection type. Write the address information in the table below. You will need to enter this information into the Router. (1) (2) (4) (3) If not already selected, select “Using DHCP” next to “Configure:” (3), then click “Apply Now”. Your network adapter(s) are now configured for use with the Router.
Manually Configuring Network Settings Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Manually Configuring Network Settings in Windows 2000, NT, XP, or Vista 1. Click “Start”, “Settings”, then “Control Panel”. 2. Double-click on the “Network and dial-up connections” icon (Windows 2000) or the “Network” icon (Windows XP or Vista). 3. Right-click on the “Local Area Connection” associated with your network adapter and select “Properties” from the drop-down menu. 4. 5.
Manually Configuring Network Settings Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Manually Configuring Network Settings in Windows 98SE or Me 1. Right-click on “My Network Neighborhood” and select “Properties” from the drop-down menu. 6. Click the “DNS Configuration” tab (1). Write the DNS address(es) in the chart. 2. Select “TCP/IP -> settings” for your installed network adapter. You will see the following window. 7.
Recommended Web Browser Settings Table of Contents sections 1 2 3 4 5 6 7 8 9 10 In most cases, you will not need to make any changes to your web browser’s settings. If you are having trouble accessing the Internet or the Web-Based Advanced User Interface, then change your browser’s settings to the recommended settings in this section. Internet Explorer 4.0 or Higher 1. 2. Start your web browser. Select “Tools” then “Internet Options”.
Recommended Web Browser Settings Table of Contents sections 1 2 3 3. Under the “Internet Options” screen, click on “Connections” and select “LAN Settings…”. 4. Make sure there are no check marks next to any of the displayed options: “Automatically detect settings”, “Use automatic configuration script”, and “Use a proxy server”. Click “OK”. Then click “OK” again in the “Internet Options” page. Enhanced Wireless Router 4 5 6 7 8 9 10 Netscape® Navigator ® 4.0 or Higher 76 1.
Troubleshooting Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Problem: Setup Assistant CD does not automatically start. Solution: If the CD-ROM does not start the Setup Assistant automatically, it could be that the computer is running other applications that are interfering with the CD drive. 1. 2. Next, double-click on the CD-ROM drive that the Setup Assistant Software CD has been placed in to start the installation.
Troubleshooting Table of Contents sections 1 2 3. The Setup Assistant should start within a few seconds. If, instead, a window appears showing the files on the CD, double-click on the icon labeled “SetupAssistant”. 4. If the Setup Assistant still does not start, reference the section titled “Manually Configuring Network Settings” (page 70) of this User Manual for an alternative setup method.
Troubleshooting Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Problem: Setup Assistant cannot find my Router. Solution: If the Setup Assistant is not able to find the Router during the installation process, please check the following items: 1. 2. 3. If the Setup Assistant is not able to find the Router during the installation process, there may be third-party firewall software installed on the computer attempting to access the Internet.
Troubleshooting Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Problem: Problem: Setup Assistant cannot connect my Router to the Internet. • The Setup Assistant completed installation, but my web browser doesn’t work. If the Setup Assistant is not able to connect the Router to the Internet, please check the following items: • I am unable to connect to the Internet. The “modem” LED on my Router is off, and the “internet” LED is blinking. 1.
Troubleshooting Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Problem: Problem: • The Setup Assistant completed installation, but my web browser doesn’t work. • The Setup Assistant completed, but my web browser doesn’t work. • I am unable to connect to the Internet. The “modem” LED on my Router is on, and the “internet” LED is blinking. • I am unable to connect to the Internet. The “modem” LED on my Router is blinking, and the “internet” LED is solid. Solution: Solution: 1.
Troubleshooting Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Problem: I can’t connect to the Internet wirelessly. Solution: If you are unable to connect to the Internet from a wireless computer, please check the following items: 1. Look at the lights on your Router. If you’re using a Belkin Router, the lights should be as follows: 3. • The “router” LED should be on. • The “modem” LED should be on, and not blinking. • The “internet” LED should be on, and not blinking.
Troubleshooting Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Problem: Problem: I can’t connect to the Internet wirelessly, but my network name is listed. I can’t connect to the Internet wirelessly, and my network name is not listed. Solution: Solution: If the name of your network is listed in the “Available Networks” list, please follow the steps below to connect wirelessly: 1. Click on the correct network name in the “Available Networks” list. 2.
Troubleshooting Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Problem: • My wireless network performance is inconsistent. • Data transfer is sometimes slow. • Signal strength is poor. • Difficulty establishing and/or maintaining a Virtual Private Network (VPN) connection. Solution: Limiting the wireless transmit rate—Limiting the wireless transmit rate can help improve the maximum wireless range and connection stability. Most wireless cards have the ability to limit the transmission rate.
Troubleshooting Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Problem: I am having difficulty setting up Wired Equivalent Privacy (WEP) security on my Belkin Router. Solution: 1. Log into your Router. For example: Open your web browser and type in the IP address of the Router. (The Router’s default is 192.168.2.1.) Log into your Router by clicking on the “Login” button in the top right-hand corner of the screen. You will be asked to enter your password.
Troubleshooting Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Problem: I am having difficulty setting up Wired Equivalent Privacy (WEP) security on a Belkin client card. Solution: The client card must use the same key as the Router. For instance, if your Router uses the key 00112233445566778899AABBCC, then the client card must be set to the exact same key. 1. Double-click the Signal Indicator icon to bring up the “Wireless Network” screen. 2.
Troubleshooting Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Problem: Problem: Do Belkin products support WPA/WPA2? I am having difficulty setting up Wireless Protected Access (WPA) security on my Belkin Router for a home network. Solution: Solution: To use WPA security, all your clients must be upgraded to drivers and software that support it. At the time of this FAQ publication, a security patch download is available, for free, from Microsoft.
Troubleshooting Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Problem: I am having difficulty setting up Wireless Protected Access (WPA) security on a Belkin wireless client card for a home network. Solution: Clients must use the same key that the G Wireless Router or access point uses. For instance, if the key is “Smith Family Network Key” in the G Wireless Router or access point, the clients must also use that same key. 1.
Troubleshooting Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Problem: I am NOT using a Belkin client card for a home network and I am having difficulty setting up Wireless Protected Access (WPA) security. Solution: If you are not using a Belkin Wireless Desktop or Wireless Notebook Network Card that is not equipped with WPA-enabled software, a file from Microsoft called “Windows XP Support Patch for Wireless Protected Access” is available for free download.
Troubleshooting Table of Contents 3. sections 1 2 3 4 5 4. Under the “Wireless Networks” tab, click the “Configure” button and you will see the following screen. 6 7 For a home or small business user, select “WPA-PSK” under “Network Administration”. Note: Select WPA (with radius server) if you are using this computer to connect to a corporate network that supports an authentication server such as a radius server. Please consult your network administrator for further information.
Troubleshooting Table of Contents sections 1 2 3 4 What’s the difference between 802.11g and draft 802.11n? 5 6 7 8 9 10 Wireless Comparison Chart Currently there are three commonly used wireless networking standards, which transmit data at very different maximum speeds. Each is based on the designation for certifying network standards. The most common wireless networking standard, 802.11g, can transmit information up to 54Mbps; 802.
Information Table of Contents sections 1 2 3 4 5 6 7 8 9 10 FCC Statement DECLARATION OF CONFORMITY WITH FCC RULES FOR ELECTROMAGNETIC COMPATIBILITY Federal Communications Commission Notice We, Belkin International, Inc., of 501 West Walnut Street, Compton, CA 90220, declare under our sole responsibility that the device, This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Information Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Modifications Europe-European Union Notice The FCC requires the user to be notified that any changes or modifications to this device that are not expressly approved by Belkin International, Inc., may void the user’s authority to operate the equipment. Radio products with the CE 0682 or CE alert marking comply with the R&TTE Directive (1995/5/EC) issued by the Commission of the European Community.
Information Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Belkin International, Inc., Limited 1-Year Product Warranty What this warranty covers. Belkin International, Inc. (“Belkin”) warrants to the original purchaser of this Belkin product that the product shall be free of defects in design, assembly, material, or workmanship.
Information Table of Contents sections 1 2 3 4 5 6 7 8 9 10 How state law relates to the warranty. THIS WARRANTY CONTAINS THE SOLE WARRANTY OF BELKIN. THERE ARE NO OTHER WARRANTIES, EXPRESSED OR, EXCEPT AS REQUIRED BY LAW, IMPLIED, INCLUDING THE IMPLIED WARRANTY OR CONDITION OF QUALITY, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND SUCH IMPLIED WARRANTIES, IF ANY, ARE LIMITED IN DURATION TO THE TERM OF THIS WARRANTY. Belkin reserves the right to review the damaged Belkin product.
Belkin International, Inc. 501 West Walnut Street Los Angeles, CA 90220, USA 310-898-1100 310-898-1111 fax Belkin Ltd. Express Business Park, Shipton Way Rushden, NN10 6GL United Kingdom +44 (0) 1933 35 2000 +44 (0) 1933 31 2000 fax Belkin B.V. Boeing Avenue 333 1119 PH Schiphol-Rijk The Netherlands +31 (0) 20 654 7300 +31 (0) 20 654 7349 fax Belkin Ltd. 4 Pioneer Avenue Tuggerah Business Park Tuggerah, NSW 2259, Australia +61 (0) 2 4350 4600 +61 (0) 2 4350 4700 fax © 2009 Belkin International, Inc.
