7640 FLAT PANEL TV WALL MOUNT INSTRUCTION MANUAL SUPPORT MURAL D'ÉCRAN PLAT MANUEL D'INSTRUCTIONS SOPORTE DE PARED PARA TV DE PANTALLA PLANA MANUAL DE INSTRUCCIONES SUPPORTO A PARETE PER TELEVISORE A SCHERMO PIATTO MANUALE DI ISTRUZIONI WANDBEFESTIGUNG FÜR FLACHBDILDSCHIRM*TV ANLEITUNGSHANDBUCH НАСТЕННЫЙ КРОНШТЕЙН ДЛЯ ПЛОСКОПАНЕЛЬНОГО ТЕЛЕВИЗОРА ИНСТРУКЦИЯ
PRECAUTIONS If at any time you are unclear about the directions and believe you need further assistance, contact Bell’O® at: 1-888-235-7646 (US/Canada) or +1-732-972-1333 (International) from 9am – 5pm EST. • NEVER EXCEED THE MAXIMUM LOAD CAPACITY OF 280 LBS (127 KG), • This mounting bracket was designed to be installed and utilized ONLY as specified in this manual.
AVERTISSEMENTS Pour toutes questions concernant les instructions ou pour tout besoin d'assistance, veuillez communiquer avec Bell’O® au : 1-888-235-7646 (USA/Canada) ou +1-732-972-1333 (International) de 9h00 à 17h00 (heure de l'Est). • NE JAMAIS DÉPASSER LA CAPACITÉ DE CHARGE MAXIMALE DE 127 KG (280 LBS). • Ce support de fixation est conçu pour être posé et utilisé UNIQUEMENT comme indiqué dans ce manuel.
ADVERTENCIAS Si en algún momento tiene dudas sobre las instrucciones y necesita asesoramiento adicional, comuníquese con Bell’O®: 1-888-235-7646 (EE. UU. y Canadá) o +1-732-972-1333 (desde otros lugares del mundo) de 9 a 17 hora del este. • NUNCA EXCEDA LA CAPACIDAD MÁXIMA DE CARGA DE 280 LBS (127 KG). • Este soporte fue diseñado para ser instalado y utilizado ÚNICAMENTE como se indica en el presente manual.
PRECAUZIONI Nel caso che, in qualsiasi momento, le istruzioni non dovessero risultare chiare o si necessitasse di ulteriore assistenza, contattare Bell’O® al numero verde: 1-888-235-7646 (da USA/Canada) oppure al +1-732-972-1333 (da altri Paesi) dalle 9.00 - 17.00 (ora costa orientale USA). • NON SUPERARE MAI LA MASSIMA CAPACITÀ DI CARICO, PARI A 127 KG. • Questo supporto è stato progettato UNICAMENTE per essere installato e utilizzato come specificato in questo manuale.
VORSICHTSMASSNAHMEN Sollten Sie sich nicht ganz klar über die Anleitungen und der Ansicht sein, dass Sie Unterstützung brauchen, setzen Sie sich bitte mit Bell’O® unter Telefonnummer 1-888-235-7646 (US/Kanada) oder + 1-732-972-1333 (International) zwischen 9 Uhr und 17 Uhr (Ostzeit) in Verbindung. • BITTE NIE DIE HÖCHSTBELASTBARKEIT VON 127 KG (280 PFD) ÜBERSCHREITEN. • Diese Konsole darf NUR so wie in diesen Anleitungen beschrieben installiert und verwendet werden.
ПРЕДУПРЕЖДЕНИЕ Если вам понадобится помощь или что–то непонятно в инструкции, обратитесь в фирму Bell’O® по телефону 1-888-235-7646 (США/Канада) или +1-732-972-1333 (для международных звонков) с 9 утра до 5 вечера (время — восточное стандартное). • НИ ПРИ КАКИХ ОБСТОЯТЕЛЬСТВАХ НЕ ПРЕВЫШАТЬ МАКСИМАЛЬНУЮ НАГРУЗКУ В 280 ФУНТОВ (127 КГ). • Этот настенный кронштейн был сконструирован для установки и использования ТОЛЬКО в соответствии со спецификациями, приведенными в этом документе.
INCLUDED PARTS PIÈCES INCLUSES PARTES INCLUIDAS PARTI INCLUSE IM LIEFERUMFANG ENTHALTENE TEILE ПОСТАВЛЯЕМЫЙ КОМПЛЕКТ (WP) Wall Plate, 1 Plaque murale, 1 Placa de pared, 1 Supporto a parete, 1 Wandplatte, 1 Настенная плата, 1 (LMA) Low Profile Monitor Arms, 2 Bras de moniteur compacts, 2 Brazos de la pantalla de perfil bajo, 2 Snodi dello schermo a basso profilo, 2 Monitorarme mit niedrigem Profil, 2 Узлы крепления монитора, обеспечивающие минимальный профиль, 2 (EC) End Covers, 2 Capuchons, 2 Cubier
INCLUDED PARTS PIÈCES INCLUSES PARTES INCLUIDAS PARTI INCLUSE IM LIEFERUMFANG ENTHALTENE TEILE ПОСТАВЛЯЕМЫЙ КОМПЛЕКТ (AB) M4 x 10mm, 2 (T) #14 x 65mm, 6 (A) M4 x 12mm, 4 (B) M4 x 22mm, 4 (AF) M8, 8 (C) M4 x 30mm, 4 (M) M8 x 20mm, 4 (G) M5 x 12mm, 4 (H) M5 x 22mm, 4 (N) M8 x 30mm, 4 (I) M5 x 30mm, 4 (O) M8 x 40mm, 4 (J) M6 x 14mm, 4 (AH)* M10 x 30mm, 4 (K) M6 x 25mm, 4 (L) M6 x 35mm, 4 *No Washer or Spacer is required with Screw (AH) *Aucune rondelle ou douille d'espacement requise avec la vi
INCLUDED PARTS PIÈCES INCLUSES PARTES INCLUIDAS PARTI INCLUSE IM LIEFERUMFANG ENTHALTENE TEILE ПОСТАВЛЯЕМЫЙ КОМПЛЕКТ (IT) Installation Template, 1 Gabarit de pose, 1 Plantilla de instalación, 1 Schema di installazione, 1 Schablone für Installation, 1 Шаблон для установки, 1 (R) M4/M5, 4 (S) M6/M8, 4 (D) M4/M5, 4 (E) M4/M5, 4 (Q) M6/M8, 4 (P) M6/M8, 4 (U) TOGGLER® brand AF8 ALLIGATOR® Anchor, 6 TOGGLER® brand ALLIGATOR® SOLID-WALL ANCHORS are patented under one or more of US Patent numbers 5,16
NECESSARY TOOLS OUTILLAGE NÉCESSAIRE HERRAMIENTAS NECESARIAS ATTREZZI NECESSARI ERFORDERLICHE WERKZEUGE НЕОБХОДИМЫЕ ИНСТРУМЕНТЫ Phillips-head Screwdriver Tournevis à tête Phillips Destornillador philips (cruz) Cacciavite Phillips Kreuzschlitzschraubenzieher Крестообразная отвертка Masking Tape Ruban de masquage Cinta de enmascarar Nastro adesivo Abdeckband Маскировочная лента Ratchet Set Clé à cliquet à douilles Equipo de trinquete Strumento Del Cricco Schaltklinke Hilfsmittel Набор инструментов с храпов
ATTACHING THE MONITOR ARMS (AMA/LMA) FIXER LES BRAS DE MONITEUR (AMA/LMA) CÓMO FIJAR LOS BRAZOS DE LA PANTALLA (AMA/LMA) FISSAGGIO DEGLI SNODI DELLO SCHERMO (AMA/LMA) BEFESTIGUNG DER MONITORARME (AMA/LMA) ПРИКРЕПЛЕНИЕ КРЕПЕЖНЫХ УЗЛОВ МОНИТОРА (AMA/LMA) SELECT THE CORRECT SCREW Before beginning, test several of the screws in your hardware kit to find the correct size and length for your television.
SELECT THE CORRECT MONITOR ARMS TO USE Two pair of Monitor Arms are included. The Adjustable Monitor Arms (AMA) can tilt from -5° back to +15° forward. The Low Profile Monitor Arms (LMA) are fixed in a 0° position, with a shorter distance between the wall and the television. SÉLECTIONNER LES BRAS DE MONITEUR QUI CONVIENNENT Deux paires de bras de moniteur sont fournis. Les bras de moniteur ajustables (AMA) s'inclinent de -5° vers l'arrière à +15° vers l'avant.
DETERMINE IF YOU NEED THE ARM EXTENSIONS (ME) If you are installing a large TV, you may need Arm Extensions (ME) to reach the mounting holes on the back of your television. To determine if these are necessary, hold one of the Adjustable Monitor Arms (AMA) up to the back of the television cabinet to see whether the Arm can reach the holes. If they do not (as shown), then attach the Extensions to both Arms.
ATTACHING THE ARM EXTENSIONS (ME) If the use of the Arm Extensions (ME) is required, apply the Arm Extensions to the top and bottom of each Adjustable Monitor Arm (AMA) using two the M8 Nuts (AF) for each. Make sure all four M8 Nuts are tightened fully before attaching the Monitor Arms to the television.
ATTACHING THE MONITOR ARMS (AMA/LMA) Attach each Monitor Arm (AMA/LMA) to the back of your television as shown. Make sure that each Washer (R for M4 or M5 screws, or S for M6 or M8 screws) is placed between the Screw and the Monitor Arm. Don’t place the Washers between the Arms and the television. FIXER LES BRAS DE MONITEUR (AMA/LMA) Fixer les deux bras de moniteur (AMA/LMA) au dos du téléviseur comme sur l'illustration.
Use spacers if Monitor Arms (AMA/LMA) do not fit firmly against the back of the television, such as when the back of the television is curved, contains larger recessed mounting holes, or some other obstruction is in the way. Spacers also provide extra room for cables. The Arms must rest securely on the spacers, and should not be loose.
INSTALLING THE WALL MOUNT IN WOOD POSER LE SUPPORT MURAL SUR DU BOIS CÓMO INSTALAR EL SOPORTE DE PARED EN MADERA INSTALLAZIONE DEL SUPPORTO A PARETE SU LEGNO INSTALLATION DER WANDBEFESTIGUNG IN HOLZ КРЕПЛЕНИЕ НАСТЕННОГО КРОНШТЕЙНА К ДЕРЕВУ DETERMINE THE CORRECT WIDTH OF THE WALL PLATE (WP) To determine the correct width of the expandable Wall Plate (WP) for your television, measure the distance from the outside edges of the Monitor Arms (AMA/LMA) on the back of your television using a tape measure.
1 Minimum Wall Plate (WP) Width Largeur minimum de la plaque murale (WP) Ancho mínimo de la placa de pared (WP) Larghezza minima del supporto a parete (WP) Mindestwandplattenbreite (WP) Минимальная ширина настенной платы (WP) 1 2 2 Maximum Wall Plate (WP) Width Largeur maximum de la plaque murale (WP) Ancho máximo de la placa de pared (WP) Larghezza massima del supporto a parete (WP) Höchstwandplattenbreite (WP) Максимальная ширина настенной платы (WP) 19
EXTENDING THE WALL PLATE (WP) Using the socket wrench, loosen and remove the four M8 Nuts and Washers that secure the three parts of the Wall Plate (WP) together. Extend the Left and Right Extension Plates to the necessary width for your TV, then secure all three of the Wall Plate's parts together again by replacing the four M8 Washers and Nuts as shown. Tighten all four M8 Nuts fully before attempting to install the Wall Plate to the wall.
56 34 2 1 2 1 4 3 5 6 Pay attention to how far you extend the Wall Plate (WP) — the amount of extension determines whether you will use four or six Lag Bolts (T) in the next step of the installation process! If you extend the Left and Right Extension Plates into (or wider than) the third expansion slot (see illustration), you must use six Lag Bolts (three studs for wood stud installations).
FIND THE WOOD STUDS Using a stud finder, find the exact location of the studs to which you want to attach the wall mount. Mark the right and left side to determine the center of each stud. TROUVER LES MONTANTS EN BOIS À l'aide d'un détecteur de montant, trouver l'emplacement exact des montants sur lesquels doit être attaché le support mural. Marquer les bords gauche et droit pour déterminer le centre de chaque montant.
DETERMINE HEIGHT LOCATION OF TELEVISION Measure the distance from the bracket holes to the top and bottom of the TV to determine the center mounting position. Measure from the floor up, and make small marks on the wall to help you determine the desired TV height. Using a level, line up the Installation Template (IT) with your pencil markings and tape it into place.
IT • Height to bottom of TV • Hauteur jusqu'au bas du téléviseur • Altura hasta la parte inferior del TV • Altezza alla parte inferiore del televisore • Höhe zum unteren Teil des TVs • Высота до низа телевизора 25
INSTALL THE SECURITY SCREW (AB) Before you attach the Wall Plate (WP) to the wall, insert the M4 x 10mm Security Screws (AB) into the locking mechanism on each end of the bracket. Insert them only half way, so that the locking arm can still be easily rotated. POSER LA VIS DE SÉCURITÉ (AB) Avant de fixer la plaque murale (WP) au mur, introduire les vis de sécurité M4 x 10 mm (AB) dans le mécanisme de verrouillage à chaque extrémité de la plaque.
FOR MASONRY INSTALLATIONS, SEE PAGE 31. POUR UNE POSE SUR DE LA MAÇONNERIE, VOIR PAGE 31. PARA INSTALACIONES EN MAMPOSTERÍA CONSULTE LA PÁGINA 31. PER INSTALLAZIONI A MURO, VEDERE A PAGINA 31. FÜR INSTALLATIONEN IN MAUERWERK, SIEHE SEITE 31. КРЕПЛЕНИЕ К КАМЕННОЙ КЛАДКЕ, СМ. СТР. 31. Use lines on Installation Template (IT) to align Template with stud pencil markings. Se servir des lignes sur le gabarit de pose (IT) pour aligner le gabarit avec repères de montants au crayon.
PERCER LES TROUS GUIDES Suivre avec attention les instructions figurant sur le gabarit de pose. Le nombre de tire-fond (T) nécessaire dépend de la largeur d'allongement de la plaque murale (WP). Si elle est allongée jusqu'au troisième trou de rallonge ou au-delà (comme sur l'illustration à la page 21), utiliser six tire-fond (T) vissés dans trois montants. Si les rallonges sont dans les premiers ou seconds trous de rallonge, utiliser quatre tire-fond vissés dans deux montants.
INSTALL THE WALL PLATE (WP) After you have prepared the holes for mounting the Wall Plate (WP), place the Wall Plate over the holes and screw in the Lag Bolts (T) about half way. Use a level to make sure the Wall Plate is level and make any necessary adjustments. Once straight, tighten all of the Lag Bolts completely (do not over tighten!).
MOUNTING TO SOLID CONCRETE, BRICKS, OR CINDER BLOCK POSE SUR DU BÉTON PLEIN, DES BRIQUES OU DES PARPAINGS MONTAJE EN CONCRETO SÓLIDO, LADRILLO O LADRILLOS DE ESCORIAS MONTAGGIO SU CALCESTRUZZO, MATTONI O BLOCCHI IN CEMENTO MONTAGE AN FESTBETON, MAUERZIEGELN ODER SCHLACKENBETONBLOCK КРЕПЛЕНИЕ К НЕАРМИРОВАННОМУ БЕТОНУ, КИРПИЧУ ИЛИ ШЛАКОБЕТОННОМУ БЛОКУ After you have determined your desired TV location, Line up the Installation Template (IT) to ensure you will not drill into any mortar joints.
DRILL PILOT HOLES Follow directions on the Installation Template (IT) carefully. The number of Lag Bolts (T) you will use will depend on how wide you expand your mount. If you expanded into or past the third expansion slot (See illustration on page 21), you need to use six Lag Bolts. If the mount is in the first or second expansion hole, use four lag bolts. Carefully drill all necessary holes using a 5/16" (or 8mm) masonry drill bit. Each hole should be at least 3" (76mm) deep.
DO NOT DRILL INTO MORTAR JOINTS! DRILL HOLES AT LEAST 1" (25.4 MM) FROM THE JOINTS. USE A NEW DRILL BIT TO ENSURE OPTIMUM HOLDING ABILITY. DO NOT USE A HAMMER DRILL! NE PAS PERCER DANS LES JOINTS DE MORTIER ! PERCER LES TROUS À AU MOINS 25 MM (1 PO) DES JOINTS. UTILISER UNE MÈCHE NEUVE POUR ASSURER UNE CAPACITÉ DE MAINTIEN OPTIMALE. NE PAS UTILISER DE PERCEUSE À PERCUSSION ! NO PERFORE LAS JUNTAS DE ARGAMASA. TALADRE ORIFICIOS A UNA DISTANCIA DE, POR LO MENOS, 1” (25,4 MM) DE LAS JUNTAS.
U INSERT ANCHORS Remove Template (IT) and insert TOGGLER® brand ALLIGATOR® Anchors (U). ENFONCER LES CHEVILLES Enlever le gabarit (IT) et enfoncer des chevilles d'ancrage ALLIGATOR® de la marque TOGGLER® (U). COLOQUE LOS ANCLAJES Quite la plantilla (IT) y coloque los anclajes (U) marca TOGGLER® Y ALLIGATOR®. INSERIRE I TASSELLI Togliere lo schema (IT) e inserire i tasselli ALLIGATOR® di marca TOGGLER® (U).
INSTALL THE WALL PLATE (WP) After you have prepared the holes for mounting the Wall Plate (WP), place the Wall Plate over the holes and screw in the Lag Bolts (T) about half way. Use a level to make sure the Wall Plate is level and make any necessary adjustments. Once straight, tighten all of the Lag Bolts completely (do not over tighten!).
INSTALL THE DECORATIVE END COVERS (EC) Line up the two peg inserts on the back of each End Cover (EC) with the two holes at the ends of the Wall Plate (WP), and press into place. Each End Cover is marked with a "L" (for Left side) or "R" (for Right side). POSER LES CAPUCHONS DÉCORATIFS (EC) Aligner les deux chevilles au dos de chaque capuchon (EC) avec les deux trous aux extrémités de la plaque murale (WP) et les enfoncer en place. Les capuchons sont marqués « L » (côté gauche) ou « R » (côté droit).
WP EC 37
MOUNTING THE TELEVISION POSE DU TÉLÉVISEUR CÓMO INSTALAR EL TELEVISOR MONTAGGIO DEL TELEVISORE MONTAGE DES FERNSEHERS УСТАНОВКА ТЕЛЕВИЗОРА UNDERSTANDING THE LOCKING MECHANISM The Locking Mechanism locks the Monitor Arms (AMA/LMA) onto the Wall Plate (WP) to prevent television removal. Before attempting to attach the television with the Monitor Arms to the Wall Plate, make sure that the Locking Mechanism is in the unlocked position.
To Unlock Déverrouiller Para destrabar Per sbloccare Entriegelung Чтобы разблокировать Locking Bar Shown Up in Unlocked Position Barre de verrouillage représentée en position haute déverrouillée Large Screw Head Grande tête de vis Punta del tornillo grande Vite a testa grande Großer Schraubkopf Большая головка винта Barra de cierre en posición destrabada.
MOUNT THE TELEVISION If using the Adjustable Monitor Arms (AMA), make sure the Arms are parallel to the TV (in the 0-degree position) before you attempt to attach the TV to the Wall Plate (WP). This position is indicated by the center marking on the arms as shown. With the help of an assistant, lift the television and guide the Monitor Arms onto the Wall Plate as shown.
AMA/LMA WP Markings on the adjustable arm will line up when in the 0-degree position. Les repères sur le bras ajustable s'alignent lorsqu'il est en position 0 degré. Las marcas en el brazo ajustable se alinearán cuando éste esté en la posición grado 0. I contrassegni sullo snodo regolabile saranno allineati quando si trovano in posizione pari a 0 gradi. Die Markierungen auf dem verstellbaren Arm sind dann in einer Reihe ausgerichtet, wenn sie sich in der 0-Grad Stellung befinden.
SECURE THE TELEVISION After the television with the Monitor Arms (AMA/LMA) is attached to the Wall Plate (WP), lock the Arms into place to prevent removal of the television. To lock the Arms, simply turn the large screw head on the side of the Wall Plate 90° toward the wall using a screwdriver. Have an assistant hold the television in place while you do this.
AB To Lock Verrouiller Para trabar Per bloccare Verriegelung Чтобы заблокировать Locking Bar Shown Down in Locked Position Large Screw Head Grande tête de vis Punta del tornillo grande Vite a testa grande Großer Schraubkopf Большая головка винта Barre de verrouillage représentée en position basse verrouillée Barra de bloqueo hacia abajo en posición trabada.
USING THE TILTING ARM FEATURE Once the television with the Monitor Arms (AMA) is securely locked on the Wall Plate (WP), you can safely adjust the tilt feature on the Arms. The Arms can tilt from -5° back to +15° forward, depending on your optimum viewing position. Have an assistant hold the television in place, and turn the lever on the Monitor Arm to loosen. It works like a ratchet so that you can loosen the lever easily in a very confined area.
ИСПОЛЬЗОВАНИЕ УЗЛОВ НАКЛОНА Когда телевизор с крепежными узлами монитора (AМА) надежно заблокирован на настенной плате (WP), можно, не опасаясь, использовать функцию наклона. Крепежные узлы можно наклонять от положения -5° назад до положения +15° вперед, в зависимости от наиболее удобного положения для просмотра. Пусть помощник удерживает телевизор на месте, а вы поверните рычаг на крепежном узле монитора, чтобы крепление ослабло.
LIMITED LIFETIME WARRANTY This Bell’O International, Corp. (“Bell’O” or “we”) mounting product SKU # 7640 (“Product”) is warranted for the life of the Product only to the original purchaser and limited to the original installation (“Warranty”). Re-installation of the Product in a different location or with a different monitor or peripheral voids this Warranty. This Warranty is only valid in the United States of America and Canada.
GARANTIE À VIE LIMITÉE Ce produit de fixation Bell’O International, Corp. (« Bell’O » ou « nous ») de n° SKU 7640 (le « Produit ») est garanti pendant la durée de vie du Produit uniquement à l'acheteur initial et dans les limites de la pose initiale (« Garantie »). La réinstallation du Produit à un emplacement différent ou avec un téléviseur ou périphérique différent annule cette Garantie. Cette garantie est valable uniquement aux États-Unis d’Amérique et au Canada.
GARANTÍA LIMITADA DE POR VIDA Este producto de montaje SKU # 7640 (“Producto”) Bell’O International, Corp. (“Bell’O” o “nosotros”) está cubierto por la garantía durante la vida del Producto solo para el comprador original y está limitada a la instalación original (“Garantía”). La Garantía solo es válida en los Estados Unidos de Norteamérica y Canadá.
GARANZIA LIMITATA A VITA Questo prodotto di supporto SKU # 7640 (“Prodotto”) di Bell’O International, Corp. (“Bell’O” o “noi”) è coperto da garanzia per la durata della vita del Prodotto unicamente per l'acquirente originale e solo per l'installazione originale (“Garanzia”). La reinstallazione del Prodotto in posizione diversa, o con schermo o periferica diversi, rende questa Garanzia nulla. Questa Garanzia vale unicamente negli Stati Uniti d'America e in Canada.
BESCHRÄNKTE GARANTIE AUF LEBENSZEIT Eine Gewährleistung für dieses Montageprodukt SKU Nr. 7640 (das "Produkt") von Bell’O International Corporation (“Bell’O” oder “wir”) wird für die Lebenszeit des Produkts nur dem ursprünglichen Käufer gegenüber zugesichert und beschränkt sich auf die ursprüngliche Installation ("Gewährleistung"). Eine erneute Installation des Produkts an einer anderen Stelle oder mit einem anderen Monitor oder an einer anderen Außenfläche macht diese Garantie ungültig.
ОГРАНИЧЕННАЯ ПОЖИЗНЕННАЯ ГАРАНТИЯ Фирма Bell’O International, Corp. (“Bell’O” или “мы”) дает гарантию на кронштейн SKU # 7640 (“Продукт”) на время жизни Продукта только первоначальному покупателю и только на первую установку (“Гарантия”). Повторная установка Продукта в другом месте, либо с другим монитором или с другой периферийной аппаратурой аннулирует эту Гарантию. Эта Гарантия имеет силу только в Соединенных Штатах Америки и Канаде.
BELL'O INTERNATIONAL CORPORATION 711 Ginesi Drive, Morganville, NJ 07751 (888) 235-7646 • (732) 972-1333 www.bello.
