USER’S GUIDE MBP30 BABY MONITOR USER’S GUIDE The features described in this user’s guide are subject to modifications without prior notice. V 0.
Welcome... to your new Motorola Baby Monitor! Thank you for purchasing the MBP30. Now you can see and hear your baby sleeping in the other room or you can monitor your older children in their playroom. Please retain your original dated sales receipt for your records. For warranty service of your Motorola product, you will need to provide a copy of your dated sales receipt to confirm warranty status. Registration is not required for warranty coverage.
Overview of your Parent unit 10 1 11 12 8 2 7 3 6 4 5 1. 2. 3. 4. 5. 6. 7. 8. Display Menu key Left key Microphone Down key Right key Up/Talk key Power/Channel/Enter key 9 9. 10. 11. 12. 13.
Overview of your Baby unit 1 5 6 2 7 4 3 1. 2. 3. 4. 5. Power LED Infrared LEDs Light sensor Microphone Camera lens 6. On/Off switch 7.
1. 2. Safety Instructions ..................................................................... 6 Getting started ............................................................................ 7 3. Using the Baby Monitor MBP30 .............................................. 11 4. MBP30 Parent Unit Menu Options........................................... 13 5. 6. 7. 8. 9. Disposal of the device (environment)..................................... 15 Cleaning..................................................
1. Safety Instructions WARNING This baby monitor is compliant with all relevant standards regarding electromagnetic fields and is, when handled as described in the User’s Guide, safe to use. Therefore, always read the instructions in this User’s Guide carefully before using the device. • Adult assembly is required. Keep small parts away from children when assembling. • This product is not a toy. Do not allow children to play with it. • This baby monitor is not a substitute for responsible adult supervision.
2.1 ENGLISH 2. Getting started Baby unit power supply 1. Connect the small plug of the power adaptor to the baby unit and the other end to the electrical outlet (110V/60Hz). NOTE Only use the enclosed power adaptor (5V DC / 500mA). 2. Slide the power switch to the ON position. The power LED will light up in green. 3. To switch off the baby unit, slide the power switch to OFF position.
2.2 Parent unit battery Installation screw Black Red 1. 2. Turn the belt clip so that it is in the hanging position. Loosen the screw in a counterclockwise direction using a small screwdriver. Remove the battery cover. 3. Insert the wire tab of the rechargeable battery pack into the contact slot as shown above and fit the battery pack into the compartment. 4. Close the battery compartment and tighten the screw in a clockwise direction. 5. Press to switch ON the parent unit. The LCD screen illuminates.
Parent unit power supply ENGLISH 2.3 IMPORTANT We recommend the rechargeable battery pack to be installed before use, so that the unit continues to work in the event of a mains power failure. 1. Connect the small plug of the power adaptor to the parent unit and the other end to the electrical outlet (110V/60Hz) NOTE Only use the enclosed power adaptor (5V DC / 1000mA). 2. The LCD screen illuminates and starts up automatically after a few seconds. 3. Press and hold to switch OFF the parent unit.
2.4 Registration The baby monitor is already pre-registered upon your purchase. You do not need to re-register it again unless the baby unit loses its link with the parent unit. Please check that you have selected the correct channel that was linked to your baby unit before you attempt to re-register your unit. To re-register your baby monitor, follow the procedure below: 1. Switch off the camera and remove the small power plug from the camera.
3.1 Setting up • Place the camera in a convenient location (for e.g. on a table) and point the lens of the camera towards the area you want to monitor. • Tilt the head of the baby unit up or down to your desired position until the parent unit gets a good reception of the baby. • To wall mount your camera, see “9. Wall mounting instructions” for more details.
• The signal strength may also be reduced by other solid structures, like walls, or by radio or electrical equipment, such as TV's, computers, cordless or mobile phones, fluorescent lights or dimmer switches. • Use of other 2.4GHz products, such as wireless networks, Bluetooth systems or microwave ovens may cause interference with this product, so keep the baby monitor away from these types of products, or turn them off if they appear to be causing interference.
Night vision The camera has 9 high-intensity infrared LEDs for picking up clear images in the dark. When the built-in photo sensor detects a low level of ambient light, the LEDs will automatically activate and the screen on the parent unit will display in black and white. 3.6 Talk function ( Press and hold on the parent unit to talk to your baby through the baby unit loudspeaker. The symbol will be displayed at the top of the LCD screen. 3.
3. 4.3 + - Press or to turn the Baby Unit Night Vision On or Off. The night lights on the baby unit will be switched on and off accordingly. Voice Activation The sound detection sensitivity level (VOX) of the Baby Monitor can be adjusted. If the baby is a quiet sleeper, the sensitivity level can be increased so that minor disturbances can be detected and transmitted to the parent unit. 1. Press to enter menu mode. or until is selected on the LCD screen. 2. Press 3. Press or to adjust the VOX level.
At the end of the product lifecycle, you should not dispose of this product with normal household waste, but take the product to a collection point for the recycling of electrical and electronic equipment. The symbol on the product, user’s guide and/or box indicates this. Some of the product materials can be re-used if you take them to a recycling point. By reusing some parts or raw materials from used products you make an important contribution to the protection of the environment.
7. Help Display No display • Try recharging or replacing the battery pack. • Reset the units. Disconnect the battery pack of the parent unit and unplug the units’ electrical power, then plug them back in. • Is the unit turned on? Press and release on the parent unit to turn it on. F Registration If the baby unit has lost its link with the parent unit • Try recharging or replacing the battery pack.
What Does this Warranty Cover? Subject to the exclusions and limitations contained below, Binatone Electronics International LTD. warrants the Motorola branded consumer products that it manufactures (“Products”) and the Motorola branded or certified accessories sold for use with these Products that it manufactures (“Accessories”) to be free from defects in materials and workmanship under normal consumer usage for the period(s) outlined below.
LIMITED WARRANTY, OTHERWISE THE REPAIR, REPLACEMENT, OR REFUND AS PROVIDED UNDER THIS EXPRESS LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER, AND IS PROVIDED IN LIEU OF ALL WARRANTIES AND MOTOROLA AND BINATONE ELECTRONICS INTERNATIONAL LTD. MAKES NO OTHER WARRANTIES OR CONDITIONS, EXPRESS OF IMPLIED. IN NO EVENT SHALL MOTOROLA OR BINATONE ELECTRONICS INTERNATIONAL LTD.
Consumer Products and Accessories that are Repaired or Replaced Ninety (90) days from the date of purchase by the first consumer purchaser of the accessory. The balance of the original warranty or for ninety (90) days from the date returned to the consumer, whichever is longer. Exclusions Normal Wear and Tear. Periodic maintenance, repair and replacement of parts due to normal wear and tear are excluded from coverage. Batteries.
Altered Products. Products or Accessories with (a) serial numbers or date tags that have been removed, altered or obliterated; (b) broken seals or that show evidence of tampering; (c) mismatched board serial numbers; or (d) nonconforming or non-Motorola branded housings, or parts, are excluded from coverage. Communication Services.
FCC Part 15 NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the Federal Communications Commission (FCC) rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
WARNING Changes or modifications to this equipment not expressively approved by the party responsible for compliance could void the user’s authority to operate the equipment. Industry Canada Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Industrie Canada Le fonctionnement est soumis aux deux conditions suivantes : (1) Cet appareil ne doit pas causer d'interférences nuisibles et; (2) Cet appareil accepte toute les interférences dont celles qui pourraient provoquer le fonctionnement involontaire de l'appareil. L'abréviation 'IC' se trouvant avant cette homologation signifie que la certification fut effectuée selon une déclaration de conformité spécifiant que les normes d'Industrie Canada ont été rencontrées.
Technical Specifications Baby unit Frequency 2.4GHz to 2.4835GHz Maximum range Extended range up to 450 feet* *Based on unobstructed line of sight. Actual range will vary depending on surroundings. Image sensor Colour CMOS Lens f 2.5mm, F 2.8 IR LED 9 pcs Power DC 5V, 500mA (Model: Kings, KSS05-050-0500U) Parent unit Frequency 2.4GHz to 2.4835GHz Display 2.4" TFT LCD Desplay colours 16.
1. ENGLISH 9. Wall mounting instructions Cut the illustration below and drill holes in the wall exactly as illustrated. 4mm 8mm headscrew head screw 60.00mm (Tolerence 1.0mm) 4mm 9.
Insert 4mm head screws (to be purchased separately) into the holes and tighten the screws. Then, align your camera with the screws and push it down. 3. Point the lens of the camera towards the area you want to monitor. Tilt the head of the baby unit up or down to your desired position until the parent unit gets a good reception of the baby. Wall mounting instructions ENGLISH 2.
Manufactured, distributed or sold by Binatone Electronics International LTD., official licensee for this product. MOTOROLA and the Stylized M Logo, and other Motorola trademarks and trade dress are owned by Motorola, Inc. and are used under license from Motorola, Inc. MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office. All other product or service names are the property of their respective owners. © Motorola, Inc. 2009. All rights reserved. Version 1.