DISCOVERY DLX OWNER’S MANUAL
TABLE OF CONTENTS PRODUCT INFORMATION Functions & Settings..................................................5 Parts........................................................................................6 Diagram...............................................................................7 Product Information..................................................8 PRODUCT INSTALLATION Seat Installation.............................................................9 Water Connection.............................
FUNCTIONS & SETTINGS Open/Close Cover Open/Close Seat Night Light Dynamic Stream Open or close the lid. Open or close the seat. Turns the night light on/off. Activate during a wash to quickly alternate between hot and cold water. This feature assists in stimulating bowel movements. Front Rear Stop Nozzle Clean Activate oscillating front wash. Press again to turn off oscillation. Activate oscillating rear wash. Press again to turn off oscillation. Stops any operations.
PARTS Intelligent Toilet DIAGRAM T-Valve (1pc) CR2030 Button Battery (2pc) Wax Ring (1pc) Flush Water Hose Remote Control (holder 1pc, screw 2pc) User Manual Bidet Hose Required Tools Drill (Dia. 0.24in) Marking Pen 6 Silicone Gun 0.91-0.
PRODUCT INFORMATION SEAT INSTALLATION Unit: Inches Side View Front View Top View 1. Check Your Water Supply The lowest acceptable water pressure is 0.14 MPa. The highest acceptable water pressure is 0.75MPa. The toilet cannot reach full cleaning functionality if the water pressure cannot reach 0.14MPa. Open the box right side up. Remove the accessories first, then remove the unit from the top as shown in the diagrams above. 2.
WATER CONNECTION REMOTE INSTALLATION Wall anchor 1. Attach the toilet hose to the T-valve and DLX. 2. Attach the bidet hose to the T-valve and DLX. 1. Drill two 6mm holes on the wall that line up with the remote bracket. Remote Control Bracket 3. Connect the T-Valve to the water supply valve. 3. Place the remote bracket over the wall anchors. 2. Install the wall anchors in the newly drilled holes. Screws 4. Use the provided screws to attach the remote control bracket to the wall.
INSTALLING & REPLACING BATTERY BOX TESTING Testing the Water Flow Installing The Battery Box 1. 1. Remove the extension cable from the back of the bowl (The cable is attached inside the back of the toilet. Tug it gently to let it free.) Open the water supply valve. 2. Check each connection for leaks 3. If leaks occur, turn off the water supply valve and re-connect the leaking components. 2. Plug the cable into the battery box. Then, secure the water-proof nuts. Connecting Power 3.
TESTING (CONT.) Matching Your Remote Control Code Power on/off Button Your remote control will be matched with a code at the time of delivery. In the case that your remote control malfunctions, match the codes as per the following method. Push the button to power on. Push and hold the button to power off. Press during a wash to stop all operations. 1. Press Front or Rear button to activate oscillating wash cycle. Press again to turn off oscillating movement. HOW TO USE Unplug your product.
HOW TO USE (CONT.) User-Friendly Design 1. Slow-closing lid/seat. Preserve your toilet’s life and allows you to close the lid/seat silently. Dryer Flush Deodorization Press the “Dryer” button. The warm air function is activated and a flush is performed. This function runs automatically. When a user stands up, the deodorizer automatically operates for 10 minutes. Kick Flush Kick Open/Close the Lid and Seat Tap the Kick Button with your foot for easy manual flushing.
MAINTENANCE Regular Maintenance Is Required To Ensure Normal Use. Warning Note: Cut off the power and water supply before maintenance. Direct water Do not spray water or detergents on the toilet, remote control or the power cord. Doing so may cause electric shock or fire. wash to the entire product is prohibited. Maintenance Of Product Surface and Ceramics 1. Wipe dust or stains with a soft wet cloth. 2. A wet soft brush, cloth, or sponge may be used to clean the ceramic area.
SPECIFICATIONS WARNINGS & SAFETY Rated voltage 120V Frequency 60Hz Rated power input 1050W (When inlet water temp in 59°F) Seat and dryer temperature range 39.4°F~104°F Water temperature range 39.4°F~95°F Water supply hose type DN15 (G1/2”) Water Inlet Maximum Pressure 14.5 psi (Maximum flowing speed: 17L/min) Toilet Flush consumption ≤1.28 gal Flush type Tornado flush Rough-in Rough-in 12in Heating Type Instant Heating Rear wash water consumption 0.11-0.
WARNINGS & SAFETY (CONT.) • Regularly pull out the power plug and wipe off any dust on the power plug using a clean dry cloth. Risk of fire. • Any person with a disability, the elderly, and children, should be using this product with the supervision of another individual. Be advised that sitting on the heated seat for an extended amount of time may result in burns. • This product is not a toy. Advise children not to play with product. Risk of injury.
WARNINGS & SAFETY (CONT.) Read the following for proper battery usage. 1. Properly install the battery according to its correct polarity. 2. Remove the battery during long periods without use. 3. Replace the battery before it reaches the end of its usage. Failure to do so may result in interrupted control signals. 4. Cover the battery with tape before disposal. This will prevent battery fluid leaks that may cause fire and/or other damages. • Place the battery out of reach of children and infant reach.
TROUBLESHOOTING Dryer Experiencing Issues With Your Product? If you experience any issues, please consult the troubleshooting guide below. If the problem persists, contact Bio Bidet support. Issue Diagnosis Solutions The dryer blows cold air. Check the dryer settings. Adjust the dryer settings. Check whether the heating element of dryer is damaged or not. Contact Bio Bidet Support. Issue Diagnosis Solutions The temperature of toilet seat is too low or is not heating.
TROUBLESHOOTING (CONT.) Toilet Unit Issue Diagnosis Solutions The product is not flushing clean when water pressure is low. The filter is blocked. Clean filter according to the instructions manual. The water pressure at home is too low. Check whether the water amount is below 3L every 10 seconds or not. If it is, we suggest you buy a pressure increasing valve. The hose is bent. Reconfigure the hose to a more smooth connection. Flush valve breakdown. The inlet pipe must be straight.
WARRANTY 5 Year Preferred Warranty Coverage Bio Bidet warrants the Discovery DLX to be free from manufacturing defects under normal use for a period of 5 years from the date of purchase. Our obligation to you under this warranty is limited to repair or replace, at our option, of defective products or parts, provided the products were properly installed and used in accordance with the instructions. We reserve the right to make inspections in order to determine the cause of defect.
Thank You Technical Support/Customer Service 7900 S Route 31 Crystal Lake, IL 60014 T: 847.458.2334 U.S TOLL FREE: 877.339.5214 support@biobidet.com www.biobidet.
