FLOW X OWNER’S MANUAL INSPIRED BY
TABLE OF CONTENTS Product Information........................................4 Product Diagram..............................................5 Parts........................................................................6 Recommended Tools.....................................7 Installation Type................................................8 Note Before Installating................................9 Installation..........................................................10 Troubleshooting Guide................
PRODUCT INFORMATION PRODUCT DIAGRAM Information produit Diagramme de produit Codes/Standards Applicable: Codes / normes applicables: Complies with: • ASME A 112.18.1/CSA B125.1 (cUPC) • NSF/ ANSI 61 • NSF/ ANSI 372 (AB1953) Conforme à: • ASME A 112.18.1/CSA B125.
PARTS RECOMMENDED TOOLS (NOT INCLUDED) Les Pièces OUTILS RECOMMANDÉS (Non Inclus) Spray Head Tête de pulvérisation Faucet Counter Weight Contrepoids • • • • • • Adjustable Wrench Safety Goggles Screwdriver Silicone Sealant Drill 4 AA Batteries • • • • • • Clé à molette Lunettes de sécurité Tournevis Mastic silicone Percer 4 piles AA Robinet MAINTENANCE Control Box & Zip Tie Boîte de contrôle et cravate de tirette Mounting Hardware (silicone washer, rubber washer, metal washer, mounting nut, screw
INSTALLATION TYPES NOTE BEFORE INSTALLING Types d’installation Remarque Avant L’installation SINGLE HOLE INSTALLATION This product includes a safety clip. The safety plug must be removed when switching between motion activated and manual operation. Installer Avec Un Orifice Normal Operating Condition Ce produit comprend un clip de sécurité. La sécurité la prise doit être retirée lors de la commutation entre le mouvement activé et opération manuelle.
INSTALLATION Installation NOTE: Flush water lines before installation to release built up impurities in water supply. REMARQUE: Rincez les conduites d’eau avant l’installation pour libérer les impuretés accumulées dans l’alimentation en eau. Step 1 for 1-hole sink Step 1 for 3-hole sink Step 2.1 Step 2.2 Insert the O-ring over the hoses, cable, and stem which are located at the bottom of the faucet. Then mount the faucet onto the sink.
INSTALLATION (CONT.) Installation (suite) 250mm(9.8in) 450mm(17 .7in ) Outle t connection Raccor t de sortie Step 3 Step 4 Step 5.1 Step 5.2 The preferred mounting distance between the spray hose and the control box is 9.8” (250mm). The preferred mounting distance from control box to the floor is 17.7” (450mm). Mount the control box under the sink using a philips head screwdriver according to the preferred dimensions. Make sure to leave some room to adjust.
INSTALLATION (CONT.) Installation (suite) Weight location label Étiquette d'emplacement de poids Step 6.1 Step 6.2 Step 7 Step 8 Connect the data cables and secure them tightly by hand. Tie the data cables together with the outlet hose using a zip tie. Do not include the pull down hose in the zip tie. Install the counterweight on the pull down hose at the marked position (it should be placed on the line). Remove the battery pack cover and battery pack. Insert 4 AA batteries.
INSTALLATION (CONT.) Installation (suite) Step 9 Step 10 Step 11 Étape 11 Connect the hot and cold supply lines onto the matching water valves and secure the connection with an adjustable wrench. Turn on the water supply. Attach and secure the spray head onto the pulldown hose. Fixez et fixez la tête de pulvérisation sur le tuyau déroulant. Étape 9 Étape 10 Branchez les lignes d’alimentation chaude et froide sur le robinets d’eau correspondants et sécuriser la connexion avec une clé à molette.
INSTALLATION (CONT.) Installation (suite) WARNING: Risk of Scalding. High water temperature can cause severe burns. Do not operate this faucet with a water supply that has a maximum temperature above 160°F (71°C) Only connect the faucet to a water supply of drinking quality at a pressure of 20 psi (139 kPa)- 80psi (551kPa). Observe all local plumbing, electrical, and building codes. Step 12 Étape 12 Open the faucet handle and wave your hand over the sensor. Set the water temperature to desired setting.
INSTALLATION (CONT.) Installation (suite) Step 13 Étape 13 Step 14 Étape 14 Pull out the spray head (the infrared sensor will start working when the spray head is pulled out). Slide the spray head back in original position, and the water turns off. Repeat the operation several times, and check for errors. If none, then the faucet is good for use. Retirez la tête de pulvérisation (le capteur infrarouge commencera à fonctionner lorsque la tête de pulvérisation sera retirée).
INSTALLATION (CONT.) Installation (suite) Screen filter Filtre d'écran Step 15.1 Étape 15.1 Step 15.2 Étape 15.2 If the water flow rate is lower than normal, there may be build up on the screen filter. Shut off the water valves, remove the outlet hose from the control box, and unscrew the inlet adapter from the control box. Take out the screen filter and clean it. Reassemble the outlet hose connector, inlet adapter, and screen filter.
TROUBLESHOOTING GUIDE Guide de dépannage Condition Possible Cause Solution Condition Possible Cause Solution Water doesn’t flow from the faucet when activated by infrared sensor and/or hand spray is pulled down. Connections my not be properly made. Use the instruction document to verify all connections were properly made. This will ensure water will flow correctly inside the faucet. Faucet Handspray feature needs to reset. Water shut off valves are not open.
TROUBLESHOOTING GUIDE Guide de dépannage État Cause possible Solution État Cause possible Solution L’eau ne coule pas du robinet lorsqu’elle est activée par le capteur infrarouge et / ou le jet manuel est abaissé. Les connexions ne peuvent pas être correctement établies. Utilisez le document d’instructions pour vérifier que toutes les connexions ont été correctement effectuées. Cela garantira que l’eau coulera correctement à l’intérieur du robinet.
5 YEAR WARRANTY GARANTIE 5 ANS 100% Coverage on all parts and labor for the entire product for all five years from original date of purchase. Our obligations under this warranty are limited to repair or replacement, at our option, of products or parts found to be defective, provided that such products were properly installed and used in accordance with instructions. BBC Innovation LLC reserves the right to make such inspections as may be necessary in order to determine the cause of the defect.
5 YEAR WARRANTY GARANTIE 5 ANS Couverture à 100% sur toutes les pièces et main-d’œuvre pour l’ensemble du produit pendant les cinq années à compter de la date d’achat d’origine. Nos obligations en vertu de cette garantie se limitent à la réparation ou au remplacement, à notre choix, des produits ou des pièces jugés défectueux, à condition que ces produits aient été correctement installés et utilisés conformément aux instructions.
Thank You BBC Innovation LCC 7900 S Route 31 Crystal Lake, IL 60014 T. 847.458.2334 support@biobidet.com biobidet.
