Instruction manual

BFH3520
A
B
C
D
E
F
Fig. 1
H
G
DESCRIPTIONS:
A. Heater Housing
B. Neck
C. Pedestal Pole with 2 Halves
D. Base
E. Locking Nut
F. Power Cord
G. Remote Control Sensor
H. Power Light
I. Mode Button
J. Oscillation Button
K. Set Temperature/Timer Buttons
+ for Up
- for Down
L. Timer Button
ASSEMBLY INSTRUCTIONS (SEE FIG. 1
AND 2)
If you are planning on using the pedestal, start
with Step 1
Step 1 – Turn the heater housing (A) upside
down and place on a firm, level surface
Step 2 – Unscrew the locking nut (E) by turning
counterclockwise. Slide the locking nut (E)
and base (D) to the end of the power cord.
Step 3 – Unclip the two halves of the pedestal
pole (C) and re-clip the two halves (C)
around the power cord (F), insert the 2
fixing screws. (see Fig. 1)
Step 4 - Screw the pedestal pole (C) clockwise
onto the neck (B) threaded end on the
bottom of the heater housing (A) until
you feel resistance. (see Fig. 2)
Step 5 – Slide the base (D) and the locking nut
(E) up the cord, smooth surface facing
up. Make sure to align the dot on the
back of the base to the dot on the
pedestal pole (C) (See Fig. 2).
Step 6 – Hold base (D) straight while tightening
the locking nut (E) by turning
clockwise.
Step 7 – Insert the power cord into the notch at
the rear of the base.
Step 8 – Carefully turn the heater upright, place
on a firm, level surface.
OPERATING INSTRUCTIONS
Frost Guard
This special setting is automatically activated
when the (AF) mode is selected. In this mode,
the heater is off until the room's temperature
reaches freezing and the heater automatically
turns on HI power. The heater will cycle ON and
OFF as it maintains the temperature between
5°C to 8°C.
Setting the Fan
Press the Mode Button ( ) once to operate
the fan only (FA).
Setting the Digital Thermostat:
Your heater is equipped with a Digital
Thermostat that allows you to set your heater to
your precise comfort level.
1. Press the Mode Button ( ) twice for manual
HI power. The heater will run continuously on
HI.
2. Press the Mode Button again for manual LO
power. The heater will run continuously on LO.
3. Press the Mode Button for a fourth time for Auto
Mode HI Power (AH) or press again for Auto
Mode LO Power (AL). In either of these modes
you may then press the up (+), and down (-)
buttons to set your desired temperature.
4. Once you have set your desired temperature,
the display will return to current room
temperature and gradually increase until the
room has reached the preset temperature.
5. If the unit will not start in the digital thermostat
mode, please make sure the “set temperature” is
higher than the current room temperature.
NOTE: It is normal for the heater to cycle ON
and OFF as it maintains the preset
temperature. To prevent the unit from cycling,
you need to raise the thermostat setting.
When the preset temperature is reached, the
fan will run for 30 seconds without heat. This
cool down process ensures an accurate and
consistent temperature reading.
6. Press the Mode Button one more time to turn
the heater to (AF) mode and one final time to
turn the heater off. When the heater is off, the
room temperature will only be displayed.
NOTE: The Mode Button can be pressed and
held for 3 seconds at any time to turn the
heater off.
NOTE: AccuTemp Plus
TM
has memory. The
digital thermostat will remember the previous
temperature setting after the unit has been
turned off. However, if the unit is unplugged, the
digital thermostat will be reset and will no longer
remember the previous temperature setting. If
you unplug the heater, you will have to reset the
digital thermostat again by following the above
instructions.
USING THE PROGRAMMABLE TIMER
AccuTemp Plus
TM
allows the user to program the
heater to turn on at a preset time, or turn off
after a set amount of time.
NOTE: At any time, the timer can be turned off
by selecting 0 hours.
U.K. and IRELAND
I
J
K
L
Fig. 4
Fig. 2
Fig. 3
C
B
D
I
J
K
BFH3520IUK06EM2 V new.qxd 6/16/06 15:13 Page 5