Assembly Instruction

ManualsBrandsBirch Lane ManualsCeiling LightsMont 3 - Light Unique / Statement Classic / Traditional Chandelier

Package Contents

1of3

Shade

6” Rod

12” Rod

Ring

Socket Collar

Socket

Assembly

Hardware Contents

Figure 1

Supply Wires

and Ground Wire

Crossbar

Lock Washer

Hex Nut

Nipple

Canopy

Chain Loop

Canopy

Lock Ring

Ceiling Canopy

Quick Link

STEP 1 Assemble the Rods and the Fixture Loop-

A. Determine the Rods (B/C) to be assembled to the Socket Assembly

(G) according to your hanging height.

B. Pass the supply wires and ground wire through the chosen rods

(B/C) and the Fixture Loop (A). Thread the Socket Assembly (G), the

chosen Rods (B/C) and the Fixture Loop (A) together. Hand tighten

until snug.

Suggested rods for Ceiling height :

8’ ceiling : use (1)6” rod and (1)12” rod

9’ ceiling : use (1)6” rod and (2)12” rods

STEP 2 Install Crossbar-

A. AA)Attach the Crossbar ( to the Outlet Box with the head of the

Green Ground Screw facing you. Secure it with Outlet Box Screws

(not included) Tighten until snug..

Figure 2

Outlet Box

Outlet Box Screw

(not included)

Green Ground Screw

Fixture Loop

STEP 3 Install Canopy Chain Loop and Nipple-

* Pliers is required for this step.

A. Thread one Hex Nut (CC) to one end of the Nipple (DD) until it is at

least 0.25” from the end. Pass one Lock Washer (BB) over the end

of the Nipple (DD) and thread the Canopy Chain Loop (EE) onto the

Nipple (DD). By using pliers, thread the Hex Nut (CC) against the

Canopy Chain Loop (EE) and hand tighten until snug.

B. Thread another Hex Nut (CC) to the middle of the Nipple (DD).

Place another Lock Washer (BB) over the Nipple (DD) and then

thread the Nipple (DD) into the Crossbar (AA) until the Nipple (DD)

is about 0.375” above the Crossbar (AA).

(3)MediumBase100WbulbsMaximum,Alternatebulb(3)23WCFLMaximum.

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement

parts.

LightSource:

EstimatedAssembly Time:

Preparation:

ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject

glass parts to any shock while in operation or shattering may result.

Assembly Instruction

Thank you for purchasing our product.

Go to the

Care + Maintenance

Summary of content (3 pages)

PAGE 1
Assembly Instruction G o t o t h e Care + Maintenance Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (3) Medium Base 100W bulbs Maximum, Alternate bulb (3) 23W CFL Maximum. Estimated Assembly Time: 30-45 minutes Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are present.
PAGE 2
C. Remove the Canopy Lock Ring (FF) from the Canopy Chain Loop (EE). Place the Ceiling Canopy (HH) over the Canopy Chain Loop (EE) against the ceiling to determine the correct position of the Nipple (DD). Thread the Canopy Lock Ring onto the Canopy Chain Loop (EE). Adjust the Nipple (DD) to allow the Ceiling Canopy (HH) to rest against the ceiling when held in place by the Canopy Lock Ring (FF). D. Remove the Canopy Lock Ring (FF) and the Ceiling Canopy (HH).
PAGE 3