Instructions / Assembly

ManualsBrandsBLACK+DECKER ManualsAppliance partsWasher Dryer Stand

Page 4

PARTS LIST

Tools Required: Screwdriver and Drill.

NOTE:

15S = 2 short butterﬂy screws. Used for installing Support Rails, to L-BP and R-BP

pieces. Must be inserted so that wing is on exterior side of unit.

25S = 14 short buttery screws. Used for installing Connecting Rails, L-BP and R-BP

pieces to vertical rails. Must be inserted so that wing is on exterior side of unit.

35M = 4 medium buttery screws. Connects diagonal support rails. Must be inserted

so that wing is on rear of unit.

45L = 6 long buttery screws. Must be inserted through vertical rail rst then

tightened into Reinforcing Bars.

SET UP & USE

25S

15S

25S

15S

Anti-tip Bracket

Connecting Rail

Anti-tip Bracket

35M

25S

45L

LF1-1

RF1-1

RB2-1

LB2-1

LF1-2

RF1-2

L-BP

R-BP

RB2-2

LB2-2

L-BP

R-BP

Reinforcing Bar

Support Rail

Summary of content (6 pages)

PAGE 1
SET UP & USE PARTS LIST Tools Required: Screwdriver and Drill. NOTE: 15S = 2 short butterfly screws. Used for installing Support Rails, to L-BP and R-BP pieces. Must be inserted so that wing is on exterior side of unit. 25S = 1 4 short butterfly screws. Used for installing Connecting Rails, L-BP and R-BP pieces to vertical rails. Must be inserted so that wing is on exterior side of unit. 35M = 4 medium butterfly screws. Connects diagonal support rails. Must be inserted so that wing is on rear of unit.
PAGE 2
SET UP & USE LF1-1 RF1-1 LB2-1 L-BP R-BP L-BP LB2-2 RB2-1 RB2-2 LF1-2 R-BP Connecting Rail RF1-2 Diagonal Support Rail Reinforcing Bar Support Rail Non-slip Pad Anti-tip Bracket 15S 25S 35M 45L Lag Type Screws Page 5
PAGE 3
CONFIGURATION ET UTILISATION LISTE DES PIÈCES Outils Requis: Tournevis et Perceuse. NOTE: 15S = 2 vis papillon courtes. Utilisé pour l’installation des Rails De Support, sur les pièces L-BP et R-BP . Doit être inséré de façon à ce que l’aile soit sur le côté extérieur de l’unité. 25S = 1 4 vis papillon courtes. Utilisé pour l’installation des Rails De Connexion, pièces L-BP et R-BP aux rails verticaux. Doit être inséré de façon à ce que l’aile soit sur le côté extérieur de l’unité.
PAGE 4
CONFIGURATION ET UTILISATION L-BP LF1-1 RF1-1 LB2-1 L-BP R-BP LB2-2 RB2-1 RB2-2 LF1-2 R-BP Rail De Connexion RF1-2 Rail de support diagonal Barre De Renfort Rail De Support Tampon Antidérapant Support Anti-Basculement 15S Page 26 25S 35M 45L Vis De Type Tire-fond
PAGE 5
CONFIGURACIÓN Y USO LISTA DE PIEZAS Herramientas necesarias: destornillador y taladro. NOTA: 15S = 2 tornillos de mariposa cortos. Se usan para instalar los rieles de soporte para las piezas L-BP y R-BP pieces. Debe insertarse de manera que el ala esté en el lado exterior de la unidad. 25S = 1 4 tornillos de mariposa cortos. Se utilizan para instalar rieles de conexión, las piezas L-BP y R-BP a los rieles verticales. Debe insertarse de manera que el ala esté en el lado exterior de la unidad.
PAGE 6
CONFIGURACIÓN Y USO L-BP LF1-1 R-BP RF1-1 LB2-1 RB2-2 LB2-2 RB2-1 LF1-2 L-BP R-BP Riel de conexión RF1-2 Riel de soporte diagonal Barra de refuerzo Riel de soporte Almohadilla antideslizante Anclaje anti-vuelco 15S 25S 35M 45L Tornillos tipo tirafondos Page 47