IHSTRUCTIOHMAHUAL BL1500 LH4500 LH5000 BEFORE RETURNING THiS PRODUCT FOR ANY REASON PLEASE CALL 1-800-544-6986 BEFOREYOU CALL,HAVETHE CATALOGNo.AND DATECODEAVAILABLE.IN MOST CASES,A BLACK & DECKER REPRESENTATIVE CAN RESOLVETHE PROBLEMOVERTHE PHONE.IF YOU HAVEA SUGGESTIONOR COMMENT,GIVEUS A CALL.YOUR FEEDBACKIS VITALTO BLACK& DECKER. SAVE THIS MANUAL FOR FUTURE REFERENCE. VEA EL ESPAI_IOL EN LA CONTRAPORTADA, INSTRUCTIVO DE OPERACION, z_ ADVERTENCIA: Form No.
WARNING: PLEASE important READ AND UNDERSTAND Safety Warnings ALL INSTRUCTIONS and instructions CAREFULLY BEFORE USING THE UNIT. To Reduce Risk of injury: • Before any use, be sure everyone using this tool reads and understands all safety instructions and other information contained • Save these instructions and review frequently prior to use and in instructing others.
Servicing of Double Insulated Appliances Your BiowerNac is double-insulated to gwe you added safety. In a double insulated appliance, two systems of insulation are provided instead of grounding. No grounding means is provided on a double insulated appliance, nor should a means for grounding be added to the appliance. Servicing a double insulated appliance requires extreme care and knowledge of the system and should be done only by qualified service personnel.
ASSEMBLY FOR BLOW MODE Z_WARNING: Before attempting is switched off and disconnected BLOW TUBE ASSEMBLY any of the assembly steps from the power supply. (FIGURES below, ensure product @ 1-4) • Ensure grill cover is attached to the power head. If not, attach cover as shown in the inset of figure 1. NOTE: Unit will not operate in blow mode without grill cover in place. Align the upper and lower tubes as shown in figure 1.
• Remove the fan cover from the bottom of the power head by pressing the spring loaded release button (located on the back of the power head) and pulling the cover off (figure 7). @ f • Attach the vacuum tube assembly to the power head (figure 8) by locating the assembly as indicated by arrow, then pivot about this point until the locking/release catch is fully engaged.
MODEL BL1500 Your blower is fitted with a single speed switch located on the top of the power head below the handle. • To turn the tool ON, rotate the knob clockwise to Position I. • To turn tool OFF, rotate the knob counterclockwise CORD RETAINER (FIGURE to the off position (0). 11) • A cord retainer is incorporated ways: into the rear of the power head. It can be used in two different J ] • To use the cord retainer as shown in figure 11A, hook the extension cord under the retainer.
As the bag fills the power of the suction will decrease, power supply. turn the blower/vac off and unplug from FOR LH5000 BAG: • Empty the shoulder collection bag by sliding the retaining bar off the bottom of the bag as shown in figure 14. z_ CAUTION: NEVER REMOVE THE COLLECTION OFF AND UNPLUGGING BAG WITHOUT FIRST TURNING THE VACUUM, NOTE: If the suction decreases and the bag is not full, the vacuum tube is probably clogged with debris.
important To assure product SAFETY and RELiABiLiTY; repairs, maintenance and adjustments (other than those listed in this manual) should be performed by authorized service centers or other qualified service organizations, always using identical replacement parts. SERVICE iNFORMATiON All Black & Decker Service Centers are staffed with trained personnel to provide customers with efficient and reliable power tool service.
MOD[ D'EMPLO| BL1500 LH5000 LH4500 AVANT DE RETOURNER CE PRODUJT POUR QUELQUE RAISON QUE CE SOIT, COMPOSER LE 1-800-544-6986 AVANT D'APPELER, AYEZ EN MAIN LE N° DE CATALOGUE ET LE CODE DE DATE. DANS LA PLUPART DES CAS, UN REPRI_SENTANT DE BLACK & DECKER PEUT RI_SOUDRE LE PROBLEME PAR TE_LEPHONE. SI VOUS AVEZ UNE SUGGESTION OU UN COMMENTAIRE, APPELEZ-NOUS. VOS IMPRESSIONS SONT CRUCIALES POUR BLACK & DECKER. CONSERVER CE MANUEL POUR UN USAGE ULTERIEUR.
ZL Avertissement : importantes LIRE ET COMPRENDRE TOUTES LES DIRECTIVES Mesures de S6curit6 AVANT D'UTILISER L'OUTIL, AFIN DE RI_DUIRE LES RISQUES DE BLESSURES • Avant toute utilisation, s'assurer que tous ceux qui se servent de I'outil lisent et comprennent routes les mesures de securit6 renseignement contenus dans le present guide. • Conserver ces mesures et les relire fr6quemment avant d'utiliser I'outil ou d'en expliquer le fonctionnement & d'autres personnes.
Z_ AVERTISSEMENT : RISQUE DE CHOC €:LECTRIQUE. s'en servir sur des surfaces mouillees et ranger & I'interieur. Afin de minimiser les risques de secousses z_ AVERTISSEMENT : RISQUE DE COUPURE. s'arr_te completement avant de retirer I'assemblage de la souffleuse ou du tube d'aspiration. Arr_ter et debrancher electriques, proteger de la pluie, ne pas I'appareil. Attendre au moins 10 secondes ou jusqu'a, ce que le ventilateur CONSERVER CES MESURES.
ASSEMBLAGE POUR LE MODE ASPIRATION SAC A BANDOULI#RE (FIG. 5) • Fixer le sac & bandouliere au bloc-moteur comme montre a. la figure 5. TUBE D'ASPIRATION (FIGURE 6, 7, 8) • Les tubes d'aspiration doivent _tre assembles avant de s'en servir. • Aligner les encoches et les triangles des tubes inf@ieur et superieur (figure 6) • Pousser le tube inferieur fermement dans le tube superieur jusqu'& ce que les triangles s'enclenchent en place. (Ne jamais se servir de ces tubes s6parement.
MODE ASPIRATEUR (FIGURE 13) (UNIQUEMENT EN MODE ASPiRATiON : UTILISATION MODELES LH4500 ET LH5000) _AVERTISSEMENT : s'assurer que I'appareil est eteint et debranch6 de sa source d'alimentation. Fixation du sac a bandouliere a I'appareil : • Retirer le tube de soufflage. • Fixer le sac & bandouliere au bloc-moteur comme montre & la figure 5.
D#:PANNAGE Probleme • L'appareil refuse de demarrer. • L'appareil refuse de demarrer. Cause possible • Le couvercle de la soufflerie ou le tube d'aspiration n'est pas install& • Cordon d'alimentation non branch& • Le fusible du circuit est grill& •Le disjoncteur est declench& • Le cordon d'alimentation ou la prise de courant est endommage(e). • L'appareil est coince ou bourr& • Des debris bouchent I'entree, la sortie ou le ventilateur.
MAHUALUE|HSTRUCCIONES BL1500 LH4500 ANTES DE DEVOLVER ESTE PRODUCTO POR CUALQUIER (55)5326-7 LH5000 MOTIVO, LLAME AL ANTES DE LLAMAR, TENGA EL NOMERO DE CAT&LOGO Y EL CODIGO DE FECHA PREPARADOS. EN LA MAYORJA DE LOS CASOS, UN REPRESENTANTE DE BLACK & DECKER PUEDE RESOLVER EL PROBLEMA POR TELEFONO. SI DESEA REALIZAR UNA SUGERENCIA O COMENTARIO, LL,&MENOS. SU OPINION ES FUNDAMENTAL CONSERVE ESTE MANUAL PARA FUTURAS PARA BLACK & DECKER. CONSULTAS.
Z_ADVERTENCIA: ADVERTENCIAS POR FAVOR LEA CUIDADOSAMENTE E INSTRUCCiONES TODAS LAS INSTRUCCIONES ANTES DE USAR LA UNIDAD. Para reducir el riesgo de lesiones: • Antes de cualquier uso, asegQrese que cualquier persona que vaya a utilizar esta herramienta lea y comprenda todas las instrucciones de seguridad y la informaci6n contenida en este manual. • Conserve estas instrucciones y repaselas con frecuencia antes de usar la herramienta e instruir a otras personas.
Servicio a aparatos con doble aislamiento Su Soplador/Aspiradora cuenta con doble aislamiento para brindarle protecci6n afiadida. En los aparatos con doble aislamiento, se cuenta con dos sistemas de aislamiento en lugar de conexi6n a tierra. No se proporciona ning5n medio de aterrizaje en un aparato con doble aislamiento, ni se requiere afiadirle ninguno.
Ensamblajedel tubo deaspirado(FIG. 6,7,8) • Lostubos deaspirado deben ensamblarse entre si antes de usarse. Alinear las muescas y los triangulos del tubo superior e inferior, figure 6) Haga coincidir las muescas y los triangulos en los tubos superior e inferior. (Nunca opere sin haberlos ensamblado.) En aras de la seguridad, los tubos no est&n hechos para separarse una vez que se han ensamblado.
• Para retirar lacubierta delventilador delaparte inferior delcabezal deimpulsion, presione elbot6n deliberaci6n conresorte (ubicado enlaparte posterior delcabezal deimpulsion) ytiredelacubierta para extraerla (figura 7). • Para conectar el conjunto de tubos de aspirado al cabezal de impulsi6n (figura 8), coloque el conjunto como Io indica la flecha y luego gire sobre este punto hasta que el pestillo de bloqueo y liberaci6n encaje perfectamente.
DETECCiON DE PROBLEMAS Problema • La unidad no enciende. Causa posible • La cubierta del ventilador o el tubo de aspirado no est#. instalado. •La unidad no enciende. • Cable desenchufado. Soluci6n posible • Instale la cubierta del ventilador para el modo sopladora o el tubo de aspirado para el modo aspiradora. • Enchufe el cargador en un tomacorriente que funcione. • Fusible quemado. • Reemplace el fusible quemado.