Noise emitted by machinery and equipment (Minibike BLATA QUADARD) - Measurement of emission sound pressure levels at a work station and at other specified positions. Levels measured by authorized person ( TUV CZ s.r.o.). Test record (no. : 815/90/06/BT/IZ/H) is deposited with producer.
QUADARD INSTRUCTION MANUAL TABLE OF CONTENTS Page INTRODUCTION................................................................................................................................ 2 PURPOSE OF USE ........................................................................................................................... 2 SAFETY WARNING .......................................................................................................................... 2 TECHNICAL SPECIFICATIONS ............
INTRODUCTION Dear customer, Thank you for purchasing this product manufactured by Blata. The proper care and maintenance that your Quadard requires is outlined in this manual. Following these instructions will ensure a long trouble-free operating life of the vehicle and your satisfaction with it. PURPOSE OF USE Quadard is designed to be driven on closed tracks with an even, smooth, and dustfree surface. This product is not designed to be used on public highways.
TECHNICAL SPECIFICATIONS ENGINE DISPLACEMENT POWER OUTPUT TORQUE CARBURETOR IGNITION STARTING CLUTCH FRAME BRAKE WHEEL RIMS TYRES front rear front rear FUEL FUEL TANK CAPACITY WEIGHT WEIGHT (incl.
UNPACKING AND SETTING UP BEFORE RIDING Your Quadard is packed with folded handlebars and brake lever. After unpacking, set up the handlebars to a comfortable position. After setting-up the handlebars, tighten the handlebar bolts (M6), the brake lever bolt, and the throttle grip bolt according to Fig.1. While tightening the bolts, do not use an excessive force. Overtightening the bolts may cause damage of the threads or other parts.
ENGINE STARTING Fill the fuel tank with pre mix fuel and refit the fuel cap. Open the fuel cock , turning it to the position “ON”, Fig. 3. Set the choke to open (position “B“, Fig. 3). Without turning the throttle grip, gently pull the starter rope twice and then on the third pull, the engine should start, Fig. 2. Do not pull the starter rope out completely! After a short period , close the choke (position “A”). Let the engine run to normal operating temperature.
RIDING Sit on the vehicle and slowly twist the throttle to start moving forward. When riding the Quadard, keep in mind the rules applicable to riding four-wheel vehicles (sit on the front part of the seat; do not lean back; try to keep the load of your body as forward as possible)! Reduce speed accordingly when going around corners. When braking, always reduce the throttle to the idle position whilst pressing the rear brake lever with the necessary force to stop the machine.
DRIVE CHAIN ADJUSTMENT Loosen the bolts (M5) on the rear axle carrier also loosen (M6) bolt on the rear brake to allow for tensioning the chain, then adjust by moving the excentric disc on the axle, the drive chain slack should be 5 mm (0,2 in). making sure not to over tighten the chain. fasten the (M5) bolts on the axle carrier remembering to tighten the M6 bolt on the brake. It is important to lubricate the chain regularly, to avoid excess wear. This will prolong the lifetime of the chain.
REAR BRAKE PADS REPLACEMENT (Fig. 7 ) First, screw in the adjusting screw on the left brake lever on the handlebars. Loosen the nuts (M5 - 914.003.01) holding the brake body to the brake holder, and pull the brake body, rearward. Do not loosen the cable retainer! Remove the two distance bushes and the two threaded bushes from the brake body. Detach both halves of the brake caliper by screwing out the nuts (M6 – 914.010.01). Remove the worn brake pads 512.054.00.
AIR FILTER CLEANING Loosen the sleeve screw, no.2 (see Fig. 3) so you can remove the air filter cover, no.1. Now you have free acces to the filter. Remove the filter, clean it in petrol and lubricate it with engine oil. To re-install the filter, reverse the procedure above. PINION REPLACEMENT (Fig. 5) First, dismantle the chain guard. Then loosen the rear axle eccentric bolts and the rear brake reaction catcher. Remove the drive chain.
215.045.01 110.001.
215.006.00 217.010.
Fig. 7 – REAR BRAKE - assembly 916.072.
13
217.010.
15
16
MIDI - QUADARD 210.000.00 MIDI - QUADARD 110.001.00 110.001.01 110.002.00 110.004.00 110.004.01 110.004.02 110.004.03 110.005.00 110.006.00 110.006.01 110.006.02 110.006.03 110.008.00 110.011.00 110.015.00 110.017.00 110.019.00 110.020.00 110.022.00 110.024.00 110.028.00 110.031.00 110.032.00 110.053.00 110.055.00 110.056.00 110.057.00 110.059.00 110.060.00 110.063.00 110.065.00 110.067.00 110.068.00 110.069.00 110.069.01 110.069.02 110.069.03 110.070.00 110.072.00 110.073.00 110.074.00 110.076.00 110.
174.004.00 174.007.00 174.022.00 214.001.00 214.002.00 214.003.00 214.006.00 214.012.01 214.015.01 514.008.01 LINING SEAT - TAIL ASSY, UNPAINTED SEAT - TAIL ASSY, PAINTED SADDLE BODY KIT COMPLETE, UNPAINTED BODY KIT COMPLETE, PAINTED FRONT FAIRING, UNPAINTED FRONT FAIRING, PAINTED REAR FENDER CHAIN COVER RUBBER WASHER 4 x 6,5 x 23,5 175.005.00 175.025.00 175.026.00 215.013.00 215.014.00 215.016.00 215.029.00 215.030.00 215.031.00 215.032.00 215.033.00 215.035.00 215.038.00 215.040.00 215.045.01 515.002.
PART NAME TORQUE SETTINGS (1 FT-LB = 1.3558 Nm) QTY TORQUE SETTING ( Nm ) ENGINE Cylinder – Bolts M6 Flange – M5 Starter case – 4 Ratchet wheel –bolt M4 Magneto (rotor) – nut M8 Starter prowls – bolts M5 Ignition coil – boltsM5 Ignition coil holder – bolt M4 Engine block – M6 4 4 3 1 1 2 2 2 5 10 5 3 3 22 5,5 5.
It is a great honour for us that you have chosen our product. Our wish is that Quadard gives you years of trouble-free enjoyment. BLATA Company - the manufacturer of your Quadard. All rights for technical, text and design changes reserved for the BLATA Company. Serial Number : CZ .......................................... Signature of the technical control: ........................................................... This manual serves also as a CERTIFICATE OF WARRANTY.
COPYRIGHT C BLATA 2006 Last update: 11.12.