Refrigerator BRFB1920SS BRFB1900FBI BRFB1920FBI
CONFIDENTIAL Table of Contents Symbols and Their Meanings ........................................................................................................................................ 3 Product weight .............................................................................................................................................................. 5 Load bearing capacity of the doors........................................................................................................
CONFIDENTIAL INSTALLING THE CABIN BOTTOM ................................................................................................................................... 49 Water connection ....................................................................................................................................................... 49 Attaching the upper vent hole part ............................................................................................................................
CONFIDENTIAL Symbols and Their Meanings Symbols used in the installation manual are as follows. Important information or useful usage tips WARNING: Conditions that may damage the product or its operating functions ATTENTION: Conditions containing serious injury risk Conditions containing electric shock risk Packaging materials of the product have been manufactured from recyclable materials in accordance with our National Environment Regulations.
CONFIDENTIAL Minimum clearances between product parts and surrounding structures must be suitable. Minimum dimensions and proper organisation of ventilation holes must be observed. The product must be connected to the mains power, and corresponding connections of other components must be suitable. The product must be disconnectable from the power supply after installation. The socket or fuse must be accessible to de-energise the product.
CONFIDENTIAL Product weight BRFB1920SS: 486.00 lbs (220.44 Kg) Load bearing capacity of the doors Max. load that the Fridge Door can bear: 55 lbs (25 kg) Max.
CONFIDENTIAL Product Information: As illustrated in the figure below, you can see the Barcode Level at the top right corner of the FRZ Compartment. Installation Place You must follow the instructions below: The floor on which the product will be installed must be capable of bearing 1,200 pounds (544 kg) minimum. Kitchen floor and the bottom of the product must be at the same level. Otherwise, problems may occur with the air suction of the product.
CONFIDENTIAL The ambient temperature must be between 55°F (13°C) and 110°F (43°C). Otherwise, function errors may arise when the product is running.
CONFIDENTIAL The appliance is provided with a NEMA 5-15 P plug and a 3-pin power cable which is in the UL list and ready to be connected to a 120 V, 60 Hz power supply. Fuse is 15 A. The appliance must be connected to a 3-pin socket. The plug must be installed only by a licensed electrician. If the electrical wiring or the electric power supply of the house needs alteration, the necessary procedures must be performed by a qualified electrician.
CONFIDENTIAL Electrical Connection Never use an extension cable. The power socket must definitely be grounded and checked by an authorised person. Location of the electrical wiring must comply with the dimensions specified in the manual. ATTENTION: RISK OF ELECTRIC SHOCK Electrical grounding is necessary. This appliance is equipped with a three-pin plug to protect you against possible electric shocks. • Do not remove the round grounding terminal from the plug.
CONFIDENTIAL TOOL LIST Tools to be used when installing the product are as follows: Cordless Drill Safety Goggles ½" Wrench Hammer Ladder Ø2.4 Drill bit Ø2.
CONFIDENTIAL ALTERNATIVES FOR INSTALLATION The product can be placed in various ways based on the kitchen design. It must be installed at a place where it is ensured that the door can be opened and closed properly. If the doors cannot be opened 90 degrees at least, you cannot completely open the drawers inside the product.
CONFIDENTIAL PREPARATION FOR INSTALLATION The instructions below have been prepared according to Built-in type. Built-in: The Appliance and Panels fully seat into the gap, and a material that can be their own box is jammed between the two kitchen cabinets or decorative columns. This is the most common installation scenario. Cabin Dimensions Cabin dimensions below must be checked before starting the installation.
CONFIDENTIAL Location of the Electrical Wiring Location of the electrical wiring must be within the range given below. ATTENTION: Do not use extension cables or two-pin adaptors and do not remove the ground terminal of the grounding cable. ATTENTION: A qualified electrician must ensure that the poles of the socket are connected correctly. Verify that the grounding of the socket is correct.
CONFIDENTIAL Location of the Water System The water connected to the water mains must be potable. Location of the water system must be within the range given below. Water system of the refrigerator must be connected to the water mains system in the house. The user must be able to switch it on/off with the valve when necessary. Objects that might pierce the water hoses or cause them to twist must not be present where the water line is installed. Pressure of the water system must be between 25-80 psi (1.7-5.
CONFIDENTIAL WARNING: Flatness of the floor where the product will be installed must be checked with a Bubble Level Tool. Uprightness of the furniture flanges must be checked with a Bubble Level Tool. If the flatness and uprightness of the product is not proper, problems may arise with the installation.
CONFIDENTIAL Product Dimensions: 16
CONFIDENTIAL 17
CONFIDENTIAL 18
CONFIDENTIAL Distances between the furniture doors and the kitchen furniture must be 1/8" (3 mm) minimum.
CONFIDENTIAL Height of the Kitchen Countertop Based on the Min./Max. Height of the Cabin; Min. Max.
CONFIDENTIAL Unpacking WARNING: At least two persons must carry the refrigerator. Use a box cutter to remove the tapes. Cut the Packaging Board with a Box Cutter through the section illustrated in dotted lines and remove it.
CONFIDENTIAL Remove the Packaging Polystyrene material. ATTENTION: Do not remove the tape of the upper door on the product until the refrigerator is placed into the cabin. Risk of tipping over.
CONFIDENTIAL Removing the Connectors on the Side Wall 1 - Side furniture connection bracket closing parts 2 - Seals between the Furniture, Door and Inner Door for the Fridge (Already attached in products with clad doors) 3 - Seals between the Furniture, Door and Inner Door for the Freezer (Already attached in products with clad doors) 4 - Upper furniture connection bracket closing part 5 - Kick plate sheet metal (Only in products with stainless steel doors) 6 - Freezer Door upper cover 23
CONFIDENTIAL Removing the Mounting Parts in the Freezer Compartment Open the Freezer Compartment door and remove the Mounting Boxes and documents in the Crisper.
CONFIDENTIAL 15 - Hanger part screws 16 - Hanger bracket part screws 17 - 90° limiting pins 29 - Cable Clamp 30 - Screw 31 - Furniture Door Preparation Template Parts in the Mounting Box in Products without Furniture Doors 7 - Anti-Tip Bracket 8 - Dowel 9 - Anti-Tip Bracket Screws 25
CONFIDENTIAL 10 - Position adjustment part 11 - Furniture Connection screws 12 - Freezer Furniture Door Adjustment Washer 13 - Fridge Furniture Door Hanger Bracket 14 - Fridge Furniture Door Hanger Part 15 - Hanger part screws 16 - Hanger bracket part screws 17 - 90° limiting pins 18 - Fridge Door side brackets 19 - Fridge Door side bracket covers 20 - Bracket screws (Fridge door connection) 21 - Bracket screws (Furniture connection) 22 - Fridge/Freezer Door middle brackets 23 - Bracket screws (Furniture co
CONFIDENTIAL Removing the FRZ Crisper Remove it manually with 4 knurled screws. Remove the Lower Crisper.
CONFIDENTIAL Removing the FRZ Door Remove 2 screws which are near the front section and connect the FRZ Door and the rail.
CONFIDENTIAL Pull the door frontward to free it from the tabs at the back and remove it. Removing the Lower Vent Hole Assembly Remove the 2 screws to take out the Lower Vent Hole Assembly.
CONFIDENTIAL Removing the Upper Vent Hole Part Remove the 2 screws to take out the Upper Vent Hole Part.
CONFIDENTIAL PRE-INSTALLATION Continue to install the product according to the instructions below. Additionally, consider national and local instructions regarding installation. Please observe the following: For the USA, The National Electrical Code, ANSI/NFPA 70 – last version/State or Municipality directives and/or regional directives. For Canada, The Canadian Electrical Code, C22.1 – last version/State or Municipality directives and/or regional directives.
CONFIDENTIAL Mark the wall for Anti-Tip Brackets (7). Use a drill to create holes for Dowels (8) at the marked points.
CONFIDENTIAL Use the hammer to fit the dowels (8). Fit the brackets (7) into their places, using 4 screws for each. You must use all of the 3 brackets to ensure safety of the product. WARNING: If you are not sure whether the existing connection parts are fit to the wall as securely as they should be, you can use alternative anti-tip methods.
CONFIDENTIAL If there is furniture at the back wall of the refrigerator, please make sure that the furniture is fixed to the wall. For this, you need to be sure that the back wall of the furniture is fixed to the concrete back wall with suitable connection parts Alternative anti-tip method: If the anti-tip brackets cannot be connected securely, you must use the alternative method below. In this method, you can use wooden girders to avoid the risk of tipping over.
CONFIDENTIAL Preparing the Water Hose and the Power Plug You will need a hose with a minimum length of 60" (1.5 meters) and a diameter of ¼" for water connections of the product during installation. A connector that has a thread with an external diameter of ¼ must be used to connect the hose end to the product. Connect the water hose to the mains, extend it and tape it to the ground. The mains cable is provided externally with the product. First of all, connect the mains cable to the socket.
CONFIDENTIAL INSTALLATION TO THE CABIN Taking the Refrigerator from the Wooden Pallet Remove the 5 brackets that connect the refrigerator to the Wooden Pallet.
CONFIDENTIAL ove the screws that hold the rear foot of the Wooden Pallet. Hold the refrigerator firmly, put its weight to the front and push the Wooden Pallet's rear part (from which you have removed the screws) sideways to remove it. WARNING: The cabin may tip over during this procedure. Make sure you are doing it safely. Recline the refrigerator slowly and pull back with the help of the casters, and then land it.
CONFIDENTIAL ATTENTION: The risk of tipping over is high as of this point. You should not open the doors until the product is placed into the cabin. Placing the refrigerator into the cabin Insert the mains water hose into the duct at the back and take it out from the front.
CONFIDENTIAL Connect the electrical plug to the socket on the product. Start the refrigerator and make sure it is energised. (You can check if the lamps of the freezer compartment are on or off to see if the product is operating) IMPORTANT INFORMATION: You can use tape and similar protectors on parts you think this is necessary to protect the edges of the furniture when placing the product. WARNING: The plug of the product must be accessible after installation.
CONFIDENTIAL IMPORTANT INFORMATION: You must attach the Freezer Door temporarily to align the product before placing it.
CONFIDENTIAL IMPORTANT INFORMATION: You must use the upper edges of the Freezer Door when aligning the product with the furniture. Adjustment of other edges are explained in the following pages.
CONFIDENTIAL Adjusting the height of the refrigerator in the cabin Adjust the refrigerator height using the adjustable feet. WARNING: First of all, raise the front feet to reduce the risk of the cabin falling frontward.
CONFIDENTIAL Raise the adjustment part from the cabin's front feet as shown in the figure below to the degree it can get under the cabin (1"). The rear feet are adjusted via Bubble Level Tool. After adjusting the adjustable feet, check the flatness in both width and depth directions.
CONFIDENTIAL IMPORTANT INFORMATION: The maximum height that the adjustable feet can reach is 2 1/2" (63 mm) and the product height is 85 3/16" (2,164 mm) Adjusting the refrigerator according to the cabin flange For products with clad doors, the position of the Refrigerator is adjusted so that the door and the furniture surface are flush. You can also use gage (10) if necessary. For products without clad doors, the product is placed using the Adjustment part (10) as shown in the figure below.
CONFIDENTIAL IMPORTANT INFORMATION: It is very important to align the upper edge of the Freezer door when aligning. All the other edges can be adjusted with the adjustment mechanisms.
CONFIDENTIAL Position of the level adjustment part (10) must be adjusted according to the thickness of the door. It can adjust the level for 6 different door thickness levels. Screwing the side brackets Attach the Side Brackets to the furniture with 10 screws (11) for each bracket. WARNING: Before starting to screw the Side and Upper brackets, please make sure that water is supplied to the product and there is no water leakage.
CONFIDENTIAL IMPORTANT INFORMATION: If you have difficulty tightening the screws, opening a reference hole with the drill will make this procedure easier.
CONFIDENTIAL Screwing the upper bracket Attach the upper bracket to the furniture with 4 screws (11). IMPORTANT INFORMATION: If you have difficulty tightening the screws, opening a reference hole with the drill will make this procedure easier.
CONFIDENTIAL INSTALLING THE CABIN BOTTOM Water connection Use the box cutter to cut the water hose from the end of the pipe it comes out, leaving a section of 10". Use the 2 wrenches to firmly connect the hose coming from the mains and the hose coming from the valve. WARNING: The hose coming from the mains must be one piece. Do not use extension hoses. WARNING: Make sure that the power is cut off when making the water connection of the product.
CONFIDENTIAL WARNING: This product is suitable for use with cold water mains only. WARNING: Pressure of the water system must be between 25-80 psi (1.7-5.5 Bar). IMPORTANT INFORMATION: Once the connection is complete, you must turn on the mains valve and make sure that there is no leakage at that point.
CONFIDENTIAL Attaching the upper vent hole part Use 2 screws to attach the upper vent hole part.
CONFIDENTIAL Attaching the lower vent hole assembly Use 2 screws to attach the lower vent hole part. IMPORTANT INFORMATION: You can move the lower vent hole forward-backward to adjust it to the kick plate in the kitchen.
CONFIDENTIAL WARNING: Forward-backward travel distance of the lower kick plate must be 15/16" (23 mm). As you can see in the figure, the decorative kick plate must not be in front of the upper vent hole level.
CONFIDENTIAL Attaching the kick plate sheet assembly Remove the paper of the kick plate sheet (5) tapes and attach it by adjusting its ground clearance. You can use a furniture part suitable for the kitchen design instead of the kick plate sheet (5). WARNING: The kick plate attached here should not block the air blow vent hole.
CONFIDENTIAL Attaching the decorative parts Attach the side closing parts (1) onto the right/left connection brackets. Attach the upper closing part (4) onto the upper connection bracket.
CONFIDENTIAL FURNITURE DOOR PREPARATION This section contains information about preparing the furniture doors and mounting them to the product. WARNING: Maximum weights of the furniture to be mounted to the product are as follows. Fridge Door: 35.7 lbs. (16.2 kg) Freezer Door: 19.8 lbs. (9 kg) Choosing the Door Thickness The door of your refrigerator can open by 115° maximum. If the door is going to open to this degree, you can choose the following thickness levels.
CONFIDENTIAL You can limit the opening degree of your door to 90° if you want.
CONFIDENTIAL Removing the Mechanism Covers Remove one screw to take out the FF Upper Cover. WARNING: There is a magnet on the FF Upper Cover. This is a functional part for the operation of the product. It should not be confused with the lower cover. Remove one screw to take out the FF Lower Cover.
CONFIDENTIAL Removing the 3D Adjusting Mechanism on the Refrigerator Remove the Upper and Lower 3D Adjusting Mechanism Assemblies from the FF Door.
CONFIDENTIAL Remove the 3D Adjusting Mechanism Assembly from the lower part of the FRZ PU Door. Take out the cradle parts from the mechanism assemblies.
CONFIDENTIAL Preparing the Fridge Furniture Door IMPORTANT INFORMATION: You must take the dimensions into account when grouping the cradle parts on the furniture door. When marking, you can use the "Clad Door Template" (31) provided with the product.
CONFIDENTIAL WARNING: Handle connection holes must be adjusted according to the handles to be used in kitchen design. WARNING: Maximum thickness of the door must be ¾" (19mm).
CONFIDENTIAL WARNING: You must use screws suitable for the door thickness. Install 2 cradles using the chipboard screws (28). You can also use the template (31) provided with the product to align these parts. It is recommended to keep this template for future reference. Attach 1 hanger sheet (14) using 2 screws (15).
CONFIDENTIAL Attach the 3D adjusting mechanisms you have removed from the door to the door cradles. The 3D adjusting mechanisms must be attached as illustrated in the figure. WARNING: FF hanger sheet and FF upper mechanism assembly must be at the upper section of the door. WARNING: When you are grouping the mechanism on the cradles, you must push it until the tab is locked. Attach the door handle to the fridge furniture door. Screws holding the door handle must not protrude.
CONFIDENTIAL Preparing the Freezer Furniture Door WARNING: Handle connection holes must be adjusted according to the handles to be used in kitchen design. WARNING: Minimum thickness of the door must be ¾" (19 mm). WARNING: You must use screws suitable for the door thickness.
CONFIDENTIAL Install 1 cradle using the chipboard screws (28). You can also use the template (31) provided with the product to align these parts. It is recommended to keep this template for future reference. Attach 3 sheet metal brackets (25) using 2 screws (26) for each.
CONFIDENTIAL Attach the 3D adjusting mechanisms you have removed from the door to the door cradles. Attach the FRZ door handle. Screws holding the door handle must not protrude.
CONFIDENTIAL Use 4 screws to group the freezer inner door on the furniture door as shown in the figure below.
CONFIDENTIAL Attach the brackets to the freezer inner door, using 1 bolt (27) for each bracket and the Crescent Washers (12) specified below. A total of 3 mm washers must be placed on the FRZ Door (2+1) on the condition that all furniture dimensions are suitable. Washers to be used are determined based on the kitchen design. WARNING: You will find more Crescent Washers than you need in the mounting box. You can use them if your kitchen design requires so.
CONFIDENTIAL Kick Plate Position Adjustment: Nominal distance of the cabin's lower door from the ground is 4" (102 mm). It can be changed to a value between 2" (51 mm) and 6" (152 mm) by changing the freezer furniture door. The Lower Vent Hole can move 23 mm forward to be aligned with the Upper Vent Hole.
CONFIDENTIAL INSTALLING FURNITURE DOORS Installing the Fridge Furniture Door Hang the freezer furniture door assembly to the refrigerator using the hanger sheet. WARNING: Make sure that the positions of the 3D Adjusting mechanisms are correct.
CONFIDENTIAL Remove the Upper FF Door fixing bracket screw. Attach the FF Hanger Bracket (13) part in the mounting box to its place with the help of 2 screws (16).
CONFIDENTIAL 73
CONFIDENTIAL Group the FF Upper Mechanism with 4 screws. Group the Lower Mechanism with 4 screws.
CONFIDENTIAL Remove 2 screws of the hanger part. Take out the hanger part.
CONFIDENTIAL Remove 2 screws of the Hanger Carrier. Take out the Hanger Carrier. WARNING: You must keep these parts for future use. You will need them if you want to change the door directions. Installing the Freezer Furniture Door Install the Freezer Furniture door assembly onto the rails.
CONFIDENTIAL Fix the Freezer Furniture door assembly onto the rails with 2 screws.
CONFIDENTIAL Adjusting the Furniture Door WARNING: The product may come with an Inox Door or as Furniture-mountable from the factory. If the product has an Inox Door, remove the brackets on the product before performing the adjustments below. Before starting to adjust the door, set the hardness level of the Fridge Door hinges to "0".
CONFIDENTIAL Remove 4 Fixing Brackets on the fridge door.
CONFIDENTIAL Loosen 3 bracket screws at the upper section of the freezer door. WARNING: These screws should never be removed. Number and dimensions of the Crescent Washers in-between will be changed based on the adjustment.
CONFIDENTIAL Remove 3 Fixing Brackets at the lower section of the freezer door. Position of the Furniture Doors to the kitchen furniture must be flush. To achieve this, You can use the 3D Adjusting system to perform fine adjustments: First of all, review the position of the grouped Furniture Doors against the kitchen furniture. Distances between furnitures must be 1/8" (3 mm), assuming that the furniture dimensions are correct. You can make door adjustments based on this distance.
CONFIDENTIAL 82
CONFIDENTIAL Adjust the Furniture Doors with the 3D adjusting mechanism. You can adjust furniture doors with the 3-axis screw mechanism. Operating principle of the mechanisms are shown below.
CONFIDENTIAL 84
CONFIDENTIAL After completing door adjustments, attach the brackets to the middle section of the Fridge door.
CONFIDENTIAL Attach additional brackets to the upper and lower sections of the Fridge Furniture Door's handle part.
CONFIDENTIAL Tighten the screws together with enough Crescent Washers to cover the clearance under the upper brackets of the Freezer Door.
CONFIDENTIAL Attach the lower-middle bracket of the Freezer Door. Attach the lower side brackets of the Freezer Door.
CONFIDENTIAL Attaching the covers Attach and screw the Upper Cover of the Fridge Door. Attach and screw the Lower Door of the Fridge Door.
CONFIDENTIAL Attach the FRZ Cover (6) using the tabs. Attach the side closing seals (2) (3).
CONFIDENTIAL HINGE ADJUSTMENT Adjusting the hardness of the hinges Use a drill to adjust the hardness of the upper and lower hinges of the FF Door. Set the hinge adjustment screw to position "1" from position "0". WARNING: The door must be fully open during this adjustment.
CONFIDENTIAL WARNING: This adjustment must definitely be performed after the door has been adjusted.
CONFIDENTIAL CHANGING THE DIRECTION OF THE FF DOOR Removing the FF clad door Set the hardness level of the hinge to "0". ATTENTION: Failure to set the hinge to "0" and continuing the installation like that may cause injury. Remove the side closing seals.
CONFIDENTIAL Loosen one screw of the Upper Cover of the Fridge Door and remove it. Loosen one screw of the Lower Cover of the Fridge Door and remove it.
CONFIDENTIAL Remove FF Lower and Upper Bracket screws. Remove the screw of FF Upper and Lower mechanisms. WARNING: The clad door will be released when these screws are removed. You must take measures to prevent the door from falling. You can tape the Furniture Door to the Inner Door or ask for help from another person.
CONFIDENTIAL Take the Fridge Furniture Door and lay it down on a table upside down. You must attach the Furniture Door by rotating it 180° based on its current position. Fix the hanger sheet to its place with 2 screws. Remove the mechanism assemblies and attach them to the other side. Make sure that the "FF TOP" mechanism assembly is attached to the upper section of the door.
CONFIDENTIAL Removing and preparing the Fridge Inner Door Remove the hinge connection screws of the Hinge Brackets. ATTENTION: The clad door will be released when these screws are removed. You must take measures to prevent the door from falling. You can tape the Furniture Door to the Inner Door or ask for help from another person.
CONFIDENTIAL Take out the FF Door and lay it down on a table. Remove the Upper Hinge brackets on the FF Door and screw them to the other side of the door.
CONFIDENTIAL 99
CONFIDENTIAL Attach the Hanger Sheet (13) using 2 screws (16). Replacing the hinges Remove the Hinge Caps located at the other side where you will fix the hinges.
CONFIDENTIAL Remove the Screw caps of the hinges.
CONFIDENTIAL Remove the lower right hinge by loosening its 2 screws and fix it to its slot at the upper Left side.
CONFIDENTIAL Remove the upper right hinge by loosening its 2 screws and fix it to its slot at the lower Left side.
CONFIDENTIAL Fix the screw caps of the hinges to their places.
CONFIDENTIAL Attach the Hinge Slot Caps removed from the left side to the Hinge Caps at the right side.
CONFIDENTIAL Installing the FF PU Door Place the Fridge Inner Door to the refrigerator and fix it with 4 screws.
CONFIDENTIAL Installing the Fridge Furniture Door and adjusting the door Please see relevant chapters. INSTALLING THE DUAL CABIN If you are going to make a dual cabin installation, you must definitely demand "Dual Cabin Installation Kit" from the authorised service. The instructions below have been prepared according to Built-in type. Built-in: The Appliance and Panels fully seat into the gap, and a material that can be their own box is jammed between the two kitchen cabinets or decorative columns.
CONFIDENTIAL Location of the Electrical Wiring Location of the electrical wiring must be within the range given below. ATTENTION: Do not use extension cables or two-pin adaptors and do not remove the ground terminal of the grounding cable. ATTENTION: A qualified electrician must ensure that the poles of the socket are connected correctly. Verify that the grounding of the socket is correct.
CONFIDENTIAL Location of the Water System The water connected to the water mains must be potable. Location of the water system must be within the range given below. Water system of the refrigerator must be connected to the water mains system in the house. The user must be able to switch it on/off with the valve when necessary. Objects that might pierce the water hoses or cause them to twist must not be present where the water line is installed. Pressure of the water system must be between 25-80 psi (1.7-5.
CONFIDENTIAL 32 - Insulation Sponge 33 - Fastener 34 - Screw 110
CONFIDENTIAL Removing the Side Brackets Remove the side brackets that are located in the middle of two cabinets.
CONFIDENTIAL Attaching the Fasteners Screw (34) the Fasteners (33) that are going to be used to connect two refrigerators together to the locations shown in the figure.
CONFIDENTIAL Stick the Insulation Sponge (32) to the side panel so that the sponge remains in between two cabins.
CONFIDENTIAL Bring the two refrigerators side by side. After making sure that they are in alignment, screw the fasteners (33) to the other refrigerator.
CONFIDENTIAL Make power and water connections of the refrigerator as explained before. Push the refrigerators into the cabin.
CONFIDENTIAL Adjust the heights of the refrigerators. WARNING: First of all, raise the front feet to reduce the risk of the cabin falling frontward.
CONFIDENTIAL You can see previous pages for other installation procedures.
