Manual

ManualsBrandsBloom Manufacturing ManualsAccessories for electrical1200W Series

BLOOM MANUFACTURING INC.

Safety, Warranty, Maintenance & Repair, Installation and Operation Manual

Bloom™ Hydraulic Cable Winches

800W, 1000W, 1100W & 1200W Series

All Bloom Speed Reducers have the model and serial number stamped on the gear case cover. Please take a

few minutes to record these numbers for future use You will need these numbers for ordering parts or gathering

Thank you for your purchase of a quality Bloom product !

few minutes to record these numbers for future use

You will need these numbers for ordering parts or gathering

service information from the factory:

Model #___________________________ Serial #___________________________

THIS MANUAL MUST BE KEPT WITH THE WINCH AT ALL TIMES AND

NEW WINCH OPERATORS MUST READ AND UNDERSTAND IT

Thank you for your purchase of a quality Bloom product !

NEW WINCH OPERATORS MUST READ AND UNDERSTAND IT

www.bloommfg.com

Email: sales@bloommfg.com engineering@bloommfg.com

B l o o m M a n u f a c t u r i n g I n c .

Winch Division

1443 220th Street

Independence, IA 50644

800-394-1139 tel

319-827-1139 tel

319-827-1140 fax

Summary of content (6 pages)

PAGE 1
BLOOM MANUFACTURING INC. Safety, Warranty, Maintenance & Repair, Installation and Operation Manual Bloom™ Hydraulic Cable Winches 800W, 1000W, 1100W & 1200W Series All Bloom Speed Reducers have the model and serial number stamped on the gear case cover. Please take a few minutes to record these numbers for future use use.
PAGE 2
TABLE OF CONTENTS 1. General Safety Requirements 2. Warranty 3. Maintenance & Repair (a) Clean and Inspect (b) Oil Change Information (c) Oil Level (d) Recommended Gear Oil (e) Attachments (parts list, assembly) 4. Speed Reducer Break In 5. Speed Reducer Installation 6. Speed Reducer Operation (a) Automatic Safety Brake Please note that not all of the above sections apply to each model purchased Merchandise may not be returned without approval from factory.
PAGE 3
Failure to Heed The Following Warnings May Result In Serious Injury Or Death WARNING • Bloom Speed Reducers are not to be used to lift, hoist, or move people. If your task involves lifting or moving people, you must use the proper equipment, not this speed Reducer. • Bloom products are sold on the strict understanding that all products selection is the full responsibility of the purchaser. • Bloom accepts no liability for the use, misuse or incorrect application of its products.
PAGE 4
(b) the product has been subject to careless or negligent misuse, damage or use of improper oil while in the possession of the purchaser or any person to whom the product was transferred by the purchaser or was installed or operated other than in accordance with the manufacturer's operating instructions. (c) the product was used with accessories not recommended by Bloom Mfg. Inc. or for loads in excess of those listed as rated for the product. (d) in the case of hydraulic motors, Bloom Mfg. Inc.
PAGE 5
Experience and common sense, along with a good inspections, will determine if they can be used again. Always coat O-Rings, bearings, bushings and the rubber parts of seals with oil during assembly. Use a light coat of thread sealing compound on pipe fittings and plugs. (b) Oil Change Information: The Speed Reducer vent/fill and drain plugs are located at the base of the face plate. Oil should be changed every 100 hours of operating time time, or every six months, months whichever comes first.
PAGE 6
Speed Reducer Installation Section 5 • To must make sure that your speed Reducer is securely mounted in order for it to function properly and to ensure safe operation. • The mount must be flat to ensure proper alignment of the gearbox. • Speed Reducers must never be fastened directly to the frame of a truck. Mounting brackets should be used. • With a hydraulically driven Speed Reducer, make sure the hydraulic system is clean and that all components function properly, especially the relief valve.