Operation Manual

28
87
45
97
23
4
97
16
88
99
99
55
88
44
17
93
93
23
75
66
45
12
11
33
92
99
28
1
7
95
95
101
102
101
101
104
102
66
104
101
107
115
107
101
116
101
101
113
107
12L
45A
75A
45A
75A
45A
45A
75A
45A
75A
45A
12R
116
102
102
95
95
102
102
77
76
75
19
45
45
110
45
116
45
116
110
116
116
ST E P 3 A SSE M B L E SE A T F R A M E A ND SE A T B A C K
7
1. Attach Seat Frame(11) to Front Upright(4) using two 3/8"X3" Bolts(88), four 3/8" Washers(101) and two
3/8" Nuts(107). Attach Seat Frame(11) to Base Frame(1) using 3/8"X4-1/2" Bolt(87), two 3/8"
Washers(101) and one 3/8" Nut(107).
2. Attach Leg Extension Arm with bearing pre-installed(12) to Seat Frame(11) by aligning holes and then
inserting Leg Extension Axle(33). Fasten Leg Extension Axle(33) using two 5/16" Spring Washers(104),
two 5/16" Washers(102) and two 5/16"X5/8" Set Screws(97). Check to ensure that Leg Extension
Arm(12) pivots freely. Attach the Right and Left Leg Extension Arms(12R & 12L) to the Leg Extension
Arm(12) by 5/16"X1/2" Set Screw(113). Moisten the center of two Cover of Foam Pads(75A) and slide
onto each end of the Right and Left Leg Extension Arms(12R & 12L). Attach Plastic Washer (45A) at
both side of Cover of Foam Pad(75A) and secure the pads with 5/16"x32mm Sunken Head Screw(116).
Note: The L Pin(55) is used to lock the Leg Extension Arm(12) into place when using the low 
cable for exercises such as arm curls, leg kicks, upright rows, etc. Remove the L Pin(55) when 
performing leg extensions and leg curls.
3. Insert Foam Roller Bar(23) into hole in Chromed Seat Adjuster(16). Moisten Foam Pad(75) with water
and slide onto each end of Foam Rollers Bar(23). Attach Plastic Washer(45A) to both side of Cover of
Foam Pad(75A) and secure the Pads with 5/16"X32mm Sunken Head Screw(116).
4. Attach Seat Pad(77) to Chromed Seat Adjuster(16) using two 3/8" Washers(101) and two 3/8"X1-3/4"
Bolts(92). Attach 25X50mm Plug(44) to Chromed Seat Adjuster(16) and 50mm SQ. Plug(41) to Seat
Frame(11). Insert Chromed Seat Adjuster(16) into Seat Frame(11) and lock into place with Pop Pin(53)
with Spring(115).
5. Attach Seat Back Adjuster(17) to Front Upright(4) using one 3/8"X3" Bolt(88) and 3/8" Nut(107). It may
be necessary to tighten this bolt, then lossen just enough to let Seat Back Adjuster(17) pivot freely.
Attach Pop Pin(53) for Seat Back Adjuster(17) to Front Upright(4). Attach two Metal Hinges(19) to top
of Seat Back Adjuster(17), then attach Back Pad(76) to Metal Hinges(19) using two 3/8"X1-3/4"
Bolts(93) and two 3/8" Washers(101). Insert Foam Roller Bar(23) into hole in Seat Back Adjuster(17).
Moisten two Foam Pads(75) with water and slide onto each end of Foam Roller(23), then attach Plastic
Washer(45A) at both side of Cover of Foam Pads(75A) and secure pads with 5/16"x32mm Sunken
Head Screw(116). Lock into place with pre-installed Set Screw.
6. Attach Weight Shroud(28) to Base Frame(1) and Top Guide Rod Retainer(7) using four 5/16"X1/2"
Bolts(95) and four 5/16" Washers(102).
Tighten all the bolts and nuts gradually.