Installation Manual

ManualsBrandsBogen ManualsElectronicsMultiple Tone Generator

Model TG4C Multiple Tone Generator is capable of generating

four distinct signals: pulsed tone, slow whoop, repeating chime,

and steady tone. Each of these four signals may be applied con-

tinuously or limited to a double burst (single burst only of the

steady tone) for alarm signaling or pre-announcement. Signals

are triggered by an external device that provides a contact

closure. Both tone level and pitch are adjustable.

The TG4C will accept a high-level (max. 1.5V RMS) input from

a program source, such as a tuner or tape deck. Tone signal

precedence over program input is built-in.When used in con-

junction with a telephone or microphone, the unit provides

pre-announcement signaling for voice messages.

The unit operates from a 12-48V DC source, with either pos-

itive or negative ground. All connections are made at screw

terminals.

INSTALLATION

CAUTION: To reduce the risk of fire or electric shock, do not

expose this unit to rain or excessive moisture.

POWER SUPPLY

The TG4C requires a power source of between 12 to 48V

DC, either positive or negative ground:

1. Connect the grounding lead from the TG4C chassis to the

positive (+) terminal if a positive grounding system is used. Be

certain that the TG4C chassis does not come into contact

with any other equipment with a negative ground.

2. If a negative-ground system is used, connect the grounding

lead to the negative (-) terminal.

Bogen accessory Model PRS40C Power Supply is available for

operation from 120V AC, 60Hz. If used, connect the

BLACK/WHITE lead from the PRS40C to the negative (-) ter-

minal of the TG4C; connect the BLACK lead to the positive

(+) terminal.

TONE LEVEL CONTROL

Tone level can be regulated by using the screwdriver-

adjustable TONE LEVEL control on the front panel. Clockwise

rotation increases the level of the tone signal.

PITCH CONTROL

A recessed, screwdriver-adjustable PITCH control is located

on the side panel and is used to adjust the frequency of the

tone signal.The signal can be varied to suit the individual appli-

cation requirement.

WIRING

The TG4C can be installed in a variety of configurations,

depending upon specific application criteria.

Figure 1 illustrates a common method of generating a tone

signal over program (e.q., tape player or tuner) input. When

the contacts of an external switching device are closed, pro-

gram input is interrupted by a burst of one of the tone signals.

For longer signal duration, connect the CONTINUOUS and

TRIGGER terminals (dashed line).The tone signal will be con-

tinuously generated until the external switch contacts

(ALARM CLOSURE) are reopened.

Note: TBA is used to mute TBA15 amplifier.

FIGURE 1 - Tone Signaling Over a Program Source

For other applications, such as pre-announcement signaling

or continuous tone signaling, contact the Bogen Applications

Engineering Department.

MODEL TG4C

MULTIPLE TONE GENERATOR

AS REQUIRED

CONNECT ONE

CLOSURE

TO CONTACT

C 74-6220-01

AUX

AMPLIFIER

TUNER

SUPPLY

TO POWER

REM STATUS

AUDIO IN

SLO WHOOP

PULSED TONE

STEADY TONE

CONT

CHIME

RESET

TRIGGER

12-48

VDC

COM

SIG OUT

TBA

Printed in Korea. 0201

Summary of content (2 pages)

PAGE 1
MODEL TG4C MULTIPLE TONE GENERATOR Model TG4C Multiple Tone Generator is capable of generating four distinct signals: pulsed tone, slow whoop, repeating chime, and steady tone. Each of these four signals may be applied continuously or limited to a double burst (single burst only of the steady tone) for alarm signaling or pre-announcement. Signals are triggered by an external device that provides a contact closure. Both tone level and pitch are adjustable.
PAGE 2
Notice Every effort was made to ensure that the information in this guide was complete and accurate at the time of printing. However, information is subject to change. Important Safety Information Always follow these basic safety precautions when installing and using the unit: 1. Read all instructions. 2. Follow all warnings and instructions marked on the product. 3. DO NOT place the product in a separate enclosure or cabinet, unless proper ventilation is provided. 4. Never spill liquid on the product. 5.