FAQ

ManualsBrandsBondera ManualsFloor Installation Tools2 in. x 25 ft. Waterproof Seam Tape for Tile

General How Tos

How do I use the Bondera tabs?

1. Grab the non-sticky end of the tabs with your fingers

2. Apply the sticky end to the liner corner diagonally

3. Pull the tab diagonally toward the opposite corner.

TIP :Do not pull the tab straight down as this may cause the liner to tear and impead removal.. The

Bondera tabs can be removed from the film and be reused. Do not remove all of the back liner at once

prior to installing, follow suggested installation instructions.

How do I cut Bondera?

There are two methods to cut Bondera for your applications.

1. Use a straight edge along with a utility knife on a safe cutting surface.

2. Teflon scissors or household scissors

TIP: Spray a light coat of oil such as cooking spray on the scissors to prevent the adhesive from

sticking to the scissors. Wipe off excess oil areas.

What side of the Bondera Tile MatSet should be applied to the substrate?

For optimal performance, dimensional stability and ease of use, there is a glass mesh embedded in

Bondera. The mesh looks like a grid and can be easily seen. Proper installation requires the non-mesh

side to be applied to the surface you wish to tile (wall, countertop etc.). Adhere tiles to the mesh side of

Bondera.

Can I apply Bondera Tile MatSet on uneven surfaces?

Bondera Tile MatSet requires a smooth level surface. Older existing walls can be leveled using a

leveling compound prior to applying Bondera. For new construction it is recommended to construct

level walls and surfaces for tiling projects.

TIP: Clean the wall surface prior to applying Bondera Tile MatSet.

What surfaces can Bondera be applied onto?

Bondera allows you to tile on most any substrate and will adhere to any surface as long as it is oil and

dust free. You must wipe the surface clean and towel dry before applying Bondera. Examples of

surfaces or substrates include: drywall, cement board, wood, laminates, coreanTM, formicaTM,

existing tile and metal.

In what direction should I install the Bondera Tile MatSet to walls and countertops?

Bondera Tile MatSet can be applied in either a vertical or horizontal direction.

Can Bondera Tile MatSet be applied directly onto wallpaper?

It is a requirement to remove the wallpaper and adhesive and repair all deficiencies in the wall prior to

applying Bondera.

Summary of content (4 pages)

PAGE 1
General How Tos How do I use the Bondera tabs? 1. Grab the non-sticky end of the tabs with your fingers 2. Apply the sticky end to the liner corner diagonally 3. Pull the tab diagonally toward the opposite corner. TIP :Do not pull the tab straight down as this may cause the liner to tear and impead removal.. The Bondera tabs can be removed from the film and be reused. Do not remove all of the back liner at once prior to installing, follow suggested installation instructions.
PAGE 2
Can Bondera Tile MatSet be applied directly onto a painted surface? As long as the surface is dry, clean and smooth Bondera will adhere to painted surfaces. Bondera is only as strong as the surface that it adheres to and should be inspected thoroughly before applying Bondera. How do I apply Bondera Tile MatSet onto a substrate 1. Use framing square and level to ensure level and square installation. 2. Unroll a manageable length of Bondera and cut to size. 3.
PAGE 3
subway tiles which are ideal for use with Bondera. How do I install tiles on Bondera Tile MatSet? Before tiling a project such as a backsplash, countertop or wall plan the layout of tiles carefully by “pre laying” several tiles on top of Bondera (with top liner ON) and find the locations where cuts will be needed and how best to balance equal size tiles especially for each end section of a wall or countertop.
PAGE 4
Prior to applying Bondera a new wall should be installed as smooth and level as possible. For an existing wall it is recommended to ensure that the wall is level and make adjustments with a joint compound. If the tile does not lay flat against the Bondera because it is warped or otherwise defective, then it is recommended to discard the tile or apply a construction adhesive to the tile to fill any gaps to ensure proper bond to Bondera.