Installation Guide
Table Of Contents
- Built-In Microwave Oven
- Table of ContentsInstallation instructions
- Safety Definitions
- IMPORTANT SAFETY INSTRUCTIONS
- READ AND SAVE THESE INSTRUCTIONS
- Before you begin
- Checklist for Installation
- 1. Before installing the appliance, be sure to verify the cabinet dimensions are correct for your appliance and that the required electrical connections are present. Make sure the electrical conduit provided on the appliance is able to reach to the p...
- 2. Move the appliance into place in front of the cabinet opening.
- 3. Remove packaging materials, leaving the bottom packaging on the appliance to avoid damage to the floor.
- 4. Team-lift the appliance directly into the cabinet cutout.
- 5. Slide the appliance all the way into place.
- 6. Fasten the appliance to the cabinet opening with the screws supplied.
- 1. Before installing the appliance, be sure to verify the cabinet dimensions are correct for your appliance and that the required electrical connections are present. Make sure the electrical conduit provided on the appliance is able to reach to the p...
- Removing Packaging
- Dimensions and Cabinet Requirements
- Electrical Installation
- Install Appliance
- Testing Operation
- Bosch® Support
- Table de MatièresInstructions d’installation
- Définitions de Sécurité
- CONSIGNES DE SÉCURITÉ IMPORTANTES
- LIRE ET CONSERVER CES CONSIGNES
- Avant de commencer
- Liste de contrôle pour l’installation
- 1. Avant d’installer l’appareil, assurez-vous de vérifier que les dimensions du caisson sont correctes pour votre appareil et que les connexions électriques requises sont présentes. Assurez-vous que le conduit électrique fourni sur l’appare...
- 2. Déplacez l’appareil devant l’avant de l’ouverture du caisson.
- 3. Retirez les matériaux d’emballage, en laissant l’emballage du fond de l’appareil pour éviter d’endommager le plancher.
- 4. L’équipe soulève l’appareil directement dans la découpe du caisson.
- 5. Glissez l’appareil en place complètement.
- 6. Fixez l’appareil dans l’ouverture du caisson avec les vis fournies.
- 1. Avant d’installer l’appareil, assurez-vous de vérifier que les dimensions du caisson sont correctes pour votre appareil et que les connexions électriques requises sont présentes. Assurez-vous que le conduit électrique fourni sur l’appare...
- Pour enlever l’emballage
- Exigences en matière de dimensions et d'armoire
- Installation électrique
- Installation de l’appareil
- Opération d’essai
- Soutien Bosch®
- ContenidoInstrucciones de instalación
- Definiciones de Seguridad
- INSTRUCCIONES DE SEGURIDAD IMPORTANTES
- LEA Y CONSERVE ESTAS INSTRUCCIONES
- Antes de empezar
- Lista de verificación de instalación
- 1. Antes de instalar el aparato, asegúrese de verificar que las medidas del gabinete sean correctas para su aparato y que estén presentes las conexiones eléctricas requeridas. Asegúrese de que el conducto eléctrico proporcionado en el aparato pu...
- 2. Mueva el aparato a su lugar, en frente de la abertura del gabinete.
- 3. Retire los materiales de embalaje, pero deje el embalaje de la parte inferior en el aparato para evitar daños al piso.
- 4. Con ayuda, levante el aparato y colóquelo directamente en el hueco del gabinete.
- 5. Deslice completamente el aparato en su lugar.
- 6. Sujete el aparato en la abertura del gabinete con los tornillos suministrados.
- 1. Antes de instalar el aparato, asegúrese de verificar que las medidas del gabinete sean correctas para su aparato y que estén presentes las conexiones eléctricas requeridas. Asegúrese de que el conducto eléctrico proporcionado en el aparato pu...
- Quitar el embalaje
- Dimensiones y requisitos del gabinete
- Instalación eléctrica
- Montaje del electrodoméstico
- Prueba del funcionamiento
- Soporte de Bosch®
5
Before you begin
Tools and parts needed
▯ Philips head screwdriver
▯ 1/8" drill bit and drill
▯ Measuring tape
Parts included
▯ Microwave oven
▯ Philips head screws
Power Requirements
The outlet must be properly grounded in accordance with
all applicable codes.
It can be installed in the back wall directly behind the
appliance.
You can also connect your appliance directly to a
compatible conventional Built-in Oven. Refer to separate
Combination Instructions.
Checklist for Installation
Use this checklist to verify that you have completed each
step of the installation process. This can help you avoid
common mistakes.
Refer to detailed instructions for each step in the
sections following this checklist.
1.
Before installing the appliance, be sure to verify the
cabinet dimensions are correct for your appliance and
that the required electrical connections are present.
Make sure the electrical conduit provided on the
appliance is able to reach to the point of connection.
Section: Dimensions and Cabinet Requirements
2.
Move the appliance into place in front of the cabinet
opening.
Section: Removing Packaging
3.
Remove packaging materials, leaving the bottom
packaging on the appliance to avoid damage to the
floor.
Section: Removing Packaging
4.
Team-lift the appliance directly into the cabinet cutout.
Section: Install Appliance, "Mount to Cabinet”
5.
Slide the appliance all the way into place.
Section: Install Appliance, "Mount to Cabinet”
6.
Fasten the appliance to the cabinet opening with the
screws supplied.
Section: Install Appliance, "Mount to Cabinet”
Always read and follow the complete installation
instructions contained in this manual.
Removing Packaging
NOTICE: To prevent damage to your floor keep the unit
in its packaging base until ready to be placed in the
cabinet opening. Do not slide the unit across the flooring.
Different models use different packaging materials.
Bracket remains in packaging base.
1.
Cut straps on outside of box.
2.
Remove cardboard box.
3.
Remove all top and side cardboard and Styrofoam
braces.
4.
Place oven in front of cabinets where it is to be
installed.
NOTICE: To avoid damage to the microwave oven, do
not grip or use the door or door handle while the
microwave oven is being handled.