USER'S MANUAL 2-CHANNEL BRIDGEABLE POWER AMPLIFIERS CXX502 I CXX1002 I CXX1602 I CXX2002 I CXX2502 4-CHANNEL BRIDGEABLE POW.ER AMPLIFIERS CXX1204 I CXX1604 I CXX2004 ..
IO~S AUDIO SYSTEMS CXX502 CXX1002 CXX1602 CXX2002 CXX2502 Two Channel MOSFET Car Audio Amplifiers CXX1204 CXX1604 CXX2004 CXX2404 Four Channel MOSFET Car Audio Amplifiers CXX2705 Five Channel MOSFET Car Audio Amplifier CXXM1250 CXXM1800 CXXM2200 Mono Block MOSFET Car Audio Amplifiers Congratulations on your USER'S MANUAL page CONTENTS 2 Introduction 2 What is included? 3 Features 3 About 2 Q operation 4 General precautions 4 Installation precautions 4 Mounting the amplifier 5 Con
Introduction What is included? With the !2~~ CHAOS EXXTREME II MOSFET amplifier series, we are introducing thirteen new amplifiers, all designed in the USA. This new series includes three monoblock amps, five 2-channel, four 4-channel amplifiers and a 5-channel amp. When first unpacking your new amplifier, please check first that the package contains all of the items below. If something is missing, contact the store where you purchased the amplifier.
Features About 2 0 operation Your new CHAOS EXXTREME II amplifier features the following: Your CHAOS EXXTREME II amplifier has been designed to operate efficiently at loads down to 2 0. This means that you can install four 8 0 speakers per channel, when using parallel wiring.
General precautions Before installing and using your new :IO~S amplifier, please become familiar with all the information contained in this manual. AUDIO SYSTEMS Please keep this manual in a safe place for future reference. • Do not open or attempt to repair this unit yourself. Dangerous high voltages are present which may result in electric shock. Refer any repairs to a qualified service technician.
Connecting the amplifier Before doing any wiring, look through this manual and identify the diagrams to follow for power, input and speaker connections for your particular installation. Be sure you understand all the connections before you proceed. 7. Insert fuse(s) into the battery fuse holder(s). 8. Recheck all connections before powering up the amplifier. 9. Set all level controls to minimum 1. Connect the power ground terminal to the closest point on the chassis of the car.
Low Level Input Wiring Low-level (RCA) input wiring is preferred for best audio performance. Always use a high-quality RCA cable for best audio performance. NOTE: Do not connect BOTH the high level and low level inputs from your receiver to your amplifier at the same time! Remote Subwoofer Control 2-Channel Amplifiers CXX502, CXX1 002, CXX1602, CXX2002, and CXX2502 BASS BOOST ~ 0 130 .:~: ..
Low Level Input Wiring Low-level (RCA) input wiring is preferred for best audio performance. Always use a high-quality RCA cable for best audio performance.
Low Level Input Wiring Low-level (RCA) input wiring is preferred for best audio performance. Always use a high-quality RCA cable for best audio performance.
High Level Input Wiring The high level input(s) should only be used when your head unit lacks RCA outputs. If the RCA outputs are not present, connect the speaker outputs from the receiver to the high level input connector of the amplifier. Be sure to observe polarity to avoid audio phase problems.
High Level Input Wiring The high level input(s) should only be used when your head unit lacks RCA outputs. If the RCA outputs are not present, connect the speaker outputs from the receiver to the high level input connector of the amplifier. Be sure to observe polarity to avoid audio phase problems.
High Level Input Wiring The high level input(s) should only be used when your head unit lacks RCA outputs. If the RCA outputs are not present, connect the speaker outputs from the receiver to the high level input connector of the amplifier. Be sure to observe polarity to avoid audio phase problems. NOTE: Do not connect BOTH the high level and low level inputs from your receiver to your amplifier at the same time! MonoBiock Amplifier CXXM1250 LOW PASS FREQUENCY SENSITIVITY LEVEL ~D J @. Lo~'••s~l @.
Power and Speaker Wiring 2-Channel Amplifiers CXX502, CXX1002, CXX1602, CXX2002, and CXX2502 ~--------------~+ RIGHT Speaker Two Channel Mode LEFT Speaker SPEAKER IMPEDANCE 2-80 FUSES TWO CHANNEL MOSFET POWER AMPLIFIER _Chassis ground point to REMOTE TURN-ON terminal of head unit .............
Power and Speaker Wiring 4-Channel Amplifiers CXX1204,CXX1604,CXX2004 and CXX2404 CH2 SPEAKER IMPEDANCE 2-8 Q Speaker CH1 Speaker Four Channel Mode ER AMPLIFIER _ _ Chassis ground point SPEAKER IMPEDANCE 2-80 to REMOTE TURN-ON terminal of head unit 0CJ FUSE I CJ Battery I SPEAKER IMPEDANCE 4-80 Connect the Negative (-) terminal of the LEFT sub woofer to the CH2 (-) amplifier terminal.
Power and Speaker Wiring Five Channel Mode CH5 Subwoofer 5-Channel Amplifier CXX2705 CH1 ~--------------~+ Speaker SPEAKER IMPEDANCE CH2 Speaker SPEAKER IMPEDANCE 2-8 0 2-8 0 FIVE CHANNEL MOSFET POWER AMPLIFI R SPEAKER IMPEDANCE 2-80 CH3 to REMOTE TURN-ON terminal of head unit Speaker CH4 0Cl +~------ Speaker Cl Battery Connect the Negative (-) terminal of the LEFT subwoofer to the CH2 (-) amplifier terminal.
Power and Speaker Wiring Monoblock Amplifiers CXXM1250 CXXM1800 and CXXM2200 ~--------------~+ Speaker SPEAKER IMPEDANCE 2-8 Q MonoBiock Mode FUSES MOSFET MONOBLOCK POWER AMPLIFIER _Chassis -:- ground point to REMOTE TURN-ON terminal of head unit 0D FUSE I D Battery I CHAOS EXXTREME II MOSFET Amplifier User's Manual- page 15
Troubleshooting If you experience operation or performance problems with this product, compare your installation with the electrical wiring diagram on the previous pages. If problems persist, read the following troubleshooting tips which may help eliminate the problems. SYMPTOM Amplifier will not power up. POSSIBLE REMEDY Check to make sure you have a good ground connection. Check that the Remote Input (Turn-On) has at least 3VDC. Check that there is battery power on the(+) terminal.
IO~S Specifications AUDIO SYSTEMS 2-Channe/ MOSFET Amplifiers MODEL CXX502 CXX1002 CXX1602 CXX2002 CXX2502 RMSPower into 40 100 W X 2 175 W X 2 240 Wx 2 300 W X 2 500 W X 2 MAX Power into 2 0 Bridged Power into 4 0 250Wx 2 500 W X 2 800 W X 2 1000 W X 2 1250W X2 500 W X 1 1000 W X 1 1600 W X 1 2000 W X 1 2500 W X 1 Min. Speaker Impedance 2 0 Stereo 4 0 Mono Bridged THD+N :s;0.01% 25Ax2 30Ax2 40Ax2 13. 78"(L) 15.75"(L) 19.
IO~S AUDIO SYSTEMS
F 0 R POWER AMPLIFIERS THIS CERTIFICATE EXTENDS BOSS AUDIO SYSTEM'S ONE YEAR ORIGINAL FACTORY WARRANTY TO A TOTAL OF SIX YEARS ON THIS AMPLIFIER WHEN INSTALLED BY AN AUTHORIZED BOSS AUDIO SYSTEMS DEALER. THE ADDITIONAL FIVE YEAR WARRANTY PERIOD COVERS PARTS AND LABOR. ALL OTHER CONDITIONS OF THE ORIGINAL WARRANTY APPLY. PLEASE RETAIN YOUR DATED PURCHASE RECEIPT TO VALIDATE THIS WARRANTY.
PLACE POSTAGE HERE
:IO~S AUDIO SYSTEMS THIS PRODUCT IS WARRANTED FOR A PERIOD OF ONE YEAR FROM THE DATE OF PURCHASE AGAINST DEFECTS IN MATERIALS AND WORKMANSHIP. THE WARRANTY IS FOR REPAIR OR REPLACEMENT AT THE SOLE DISCRETION OF THE SELLING DEALER. IF WE CHOOSE TO REPLACE YOUR PRODUCT, WE MAY REPLACE IT WITH A NEW OR RECONDITIONED ONE OF THE SAME OR SIMILAR DESIGN. CUSTOMER WILL BE RESPONSIBLE FOR FREIGHT CHARGES INCURRED TO RETURN THE PRODUCT AND WILL INCLUDE A CASHIER'S CHECK OR MONEY ORDER IN THE AMOUNT OF $20.
Boss Audio Systems Free Extended Warranty Program When you purchase directly from BossAudio.com, one of our “Authorized Platinum Online Dealers” or have your product installed at an authorized Boss Audio dealer at the time of purchase, you qualify a free extended warranty on the product you purchased as shown below. Mobile Video & CD and DVD Receivers: 3 Years Total Boss Audio will extend the warranty for an additional two years, 3 years total, directly to the original consumer.