Installation / Operation Instruction Manual

ManualsBrandsBradford White ManualsCommercial1. KwickShot ® Flow Controlled Tankless Electric (TEF)

“Flow Controlled”

ELECTRIC INSTANTANEOUS TANKLESS

WATER HEATER

INSTALLATION GUIDE AND OWNERS MANUAL

WARNING

BEFORE ATTEMPTING INSTALLATION OF THIS UNIT OR MAKING ANY

ADJUSTMENTS TO THE UNIT, BE SURE CIRCUIT BREAKER IS OFF

TO PREVENT DANGER OF SERIOUS ELECTRIC SHOCK.

FAILURE TO GROUND THE SYSTEM MAY RESULT IN SERIOUS INJURY OR DEATH

INSTALLER/ CONSUMER RESPONSIBILITIES

READ THIS MANUAL CAREFULLY BEFORE ATTEMPTING TO INSTALL OR

OPERATE THIS WATER HEATING UNIT. IF THE SAFETY RULES ARE NOT

FOLLOWED, THE UNIT WILL NOT OPERATE PROPERLY AND COULD CAUSE

DEATH, SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE.

WARRANTY OF THIS WILL DEPEND ON PROPER INSTALLATION AND

OPERATION. THE WARRANTY WILL BE VOID IF THE DESIGN HAS BEEN

ALTERED IN ANY WAY WHATSOEVER. THE MANUFACTURER OF THIS UNIT WILL

NOT BE LIABLE FOR ANY DAMAGES BECAUSE OF FAILURE TO COMPLY WITH

THE INSTALLATION AND OPERATING INSTRUCTIONS OUTLINED ON THE

FOLLOWING PAGES.

THE INSTALLATION MUST CONFORM WITH THE INSTRUCTIONS IN THIS

MANUAL AND LOCAL CODES, OR IN THE ABSENCE OF

LOCAL CODES, WITH THE LATEST EDITION OF THE

NATIONAL ELECTRICAL CODE. THE N.E.C. IS AVAILABLE FROM

UNDERWRITERS LABORATORIES, 333 PFINGSTEN RD.,

NORTHBROOK, IL. 60062

IF ASSISTANCE IS REQUIRED OR ANY QUESTIONS ARISE CONTACT

TECHNICAL SERVICE DEPARTMENT TOLL FREE:1-800-343-3393.

HAVE THE INFORMATION LISTED BELOW BEFORE CALLING:

MODEL NO.___________SERIAL NO.___________INSTALLATION DATE_____

COMPRESSION

NUT

PART#EX17

TRIAC

PART #

EX18

CONTROL BOARD

EX101 for 240v,

EX08 for 208v

EX08 for 277V

COMPRESSION

SLEEVE

PART # EX16

ELEMENT CARTRIDGE

HEATER MODEL/ORDER REF. CARTRIDGE REF #

Replacement Parts for “Flow Controlled” Units

MODELS COVERED:

EFC-5500-S-10 240V EFC-8300-S-10 208V

EFC-6500-S-10 240V EFC-6000-S-10 277V

EFC-7500-S-10 240V EFC-8000-S-10 277V

EFC-9500-S-10 240V EFC-9000-S-10 277V

EFC-10000-S-10 277V

EFC-5500-S-10 EX1050

EFC-6500-S-10 EX890

EFC-7800-S-10 EX770

EFC-9500-S-10 EX630

EFC-8000-S-10 EX520

Summary of content (5 pages)

PAGE 1
Replacement Parts for “Flow Controlled” Units ELECTRIC INSTANTANEOUS TANKLESS WATER HEATER INSTALLATION GUIDE AND OWNERS MANUAL “Flow Controlled” TRIAC PART # EX18 MODELS COVERED: EFC-5500-S-10 240V EFC-8300-S-10 208V EFC-6500-S-10 240V EFC-6000-S-10 277V EFC-7500-S-10 240V EFC-8000-S-10 277V EFC-9500-S-10 240V EFC-9000-S-10 277V EFC-10000-S-10 ELEMENT CARTRIDGE HEATER MODEL/ORDER REF.
PAGE 2
GENERAL This “Flow Controlled” water heating unit is specifically designed to take in cold water only and heat it to temperatures suitable for the normal domestic usage up to a maximum of 1400 F(60°C). To obtain optimum performance and energy savings, this unit should be located as close as possible to the point of use. This unit is supplied with compression rings and nuts suitable for direct coupling to 1/2”(5/8 OD) copper or plastic piping. Do not use additional screwed fittings or standard pipe dope.
PAGE 3
MOUNTING THE UNIT 1) The unit should be mounted as close to the point of use as possible. 2) This unit must only be mounted in the vertical position with the water fittings at the bottom of the unit. Mounting other than in the vertical position WILL cause element burn out. 3) The cold water inlet is on the right hand side and the hot water outlet is on the left hand side. Under NO circumstances can these be reversed. 4) Leave a minimum of 8” ABOVE the unit for easy replacement of the element.
PAGE 4
PLUMBING CONNECTIONS OPERATING THE WATER HEATER IMPORTANT Before switching “on” the power at the circuit breaker the hot water circuit must be free of air pockets or premature failure of the heating element will occur. To do this, open all hot water faucets one at a time for a minute or two until the water flow is continuous and free from “gulping” and from visible air pockets. 1) With inlet and outlet BALL VALVES fully open, turn on all hot water outlets serviced by the unit.
PAGE 5
ELECTRICAL CONNECTIONS FIGURE 2 4 1/4 inches WARNING BEFORE BEGINNING ANY WORK ON THE INSTALLATION BE SURE THAT THE CIRCUIT BREAKER IS “OFF” TO AVOID ANY DANGER OF SHOCK. MOUNTING HOLES This water heating unit must have its own independent circuit using insulated, UL listed, 3 wire cable of the appropriate size suitable for use up to 75 oC protected by the correctly rated circuit breaker. TABLE 1.