Installation / Operation Instruction Manual

ManualsBrandsBradford White ManualsCommercial1. KwickShot ® Flow Controlled Tankless Electric (TEF)

ELECTRIC INSTANTANEOUS TANKLESS WATER HEATER

INSTALLATION GUIDE AND OWNERS MANUAL

ELEMENT CARTRIDGE

HEATER MODEL/ORDER REF. CARTRIDGE REF #

RELAY

PART#EX250B-

EX254B

FLOW RESTRICTOR

AERATOR

PART # EX0061-0.5-AER

CONTROL BOARD

EX0183DL-30A for

120V, 277V,

240V, 208V

REPLACEMENT PARTS FOR “Single Point” MODELS

CALL TECHNICAL SERVICE

@ 1-800-334-3393

COMPRESSION

SLEEVE 3/8”

PART # EX68C

COMPRESSION

NUT 3/8”

PART #EX68B

WARNING

BEFORE ATTEMPTING INSTALLATION OF THIS UNIT OR MAKING ANY

ADJUSTMENTS TO THE UNIT, BE SURE CIRCUIT BREAKER IS OFF

TO PREVENT DANGER OF SERIOUS ELECTRIC SHOCK.

FAILURE TO GROUND THE SYSTEM MAY RESULT IN SERIOUS INJURY OR DEATH

INSTALLER/ CONSUMER RESPONSIBILITIES

READ THIS MANUAL CAREFULLY BEFORE ATTEMPTING TO INSTALL OR

OPERATE THIS WATER HEATING UNIT. IF THE SAFETY RULES ARE NOT

FOLLOWED, THE UNIT WILL NOT OPERATE PROPERLY AND COULD CAUSE

DEATH, SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. WARRANTY

OF THIS UNIT WILL DEPEND ON PROPER INSTALLATION AND OPERATION.

THE WARRANTY WILL BE VOID IF THE DESIGN HAS BEEN ALTERED IN ANY WAY

WHATSOEVER. THE MANUFACTURER OF THIS UNIT WILL NOT BE LIABLE

FOR ANY DAMAGES BECAUSE OF FAILURE TO COMPLY WITH THE INSTALLATION

AND OPERATING INSTRUCTIONS OUTLINED ON THE FOLLOWING PAGES.

THE INSTALLATION MUST CONFORM WITH THE INSTRUCTIONS IN THIS

MANUAL AND THE LOCAL CODES, OR IN THE ABSENCE OF LOCAL CODES,

WITH THE LATEST EDITION OF THE NATIONAL ELECTRICAL CODE. THE

NATINOAL ELECTRICAL CODE IS AVAILABLE FROM WRITING

UNDERWRITERS LABORATORIES, 333 PFINGSTEN RD.,

NORTHBROOK, IL. 60062

IF ASSTANCE IS REQUIRED OR ANY QUESTIONS RELATING

TO THE INSTALLATION OR PERFORMANCE OF THIS UNIT ARISE,

PLEASE CONTACT

TECHNICAL SERVICE TOLL FREE:1-800-334-3393.

HAVE THE INFORMATION LISTED BELOW BEFORE CALLING:

MODEL NO.___________SERIAL NO.___________INSTALLATION DATE_____

“SINGLE POINT”

MODELS COVERED:

ES-2400-1-S-10 ES-3000-1-S-10

ES-3000-2-S-10 ES-3000-5-S-10

ES-3500-1-S-10 ES-3500-4-S-10

ES-4100-2-S-10 ES-4100-5-S-10

ES-5500-4-S-10

ES-2400-1-S-10 120V EX610SP

ES-3000-1--S-10 120V EX480SP

ES-3500-1-S-10 120V EX410SP

ES-3000-2-S-10 120V EX1440SP

ES-4100-2-S-10 208V EX1050SP

ES-3500-5-S-10 240V EX1650SP

ES-4100-5-S-10 277V EX1870SP

ES-3000-5-S-10 277V EX2500SP

ES-5500-4-S-10 240V EX1050SP

INSTALL

THIS WAY UP

ONLY !

relay

Summary of content (4 pages)

PAGE 1
REPLACEMENT PARTS FOR “Single Point” MODELS CALL TECHNICAL SERVICE @ 1-800-334-3393 COMPRESSION SLEEVE 3/8” PART # EX68C COMPRESSION NUT 3/8” PART #EX68B ELECTRIC INSTANTANEOUS TANKLESS WATER HEATER INSTALLATION GUIDE AND OWNERS MANUAL “SINGLE POINT” MODELS COVERED: ES-2400-1-S-10 ES-3000-1-S-10 ES-3000-2-S-10 ES-3000-5-S-10 ES-3500-1-S-10 ES-3500-4-S-10 ES-4100-2-S-10 ES-4100-5-S-10 ES-5500-4-S-10 CONTROL BOARD EX0183DL-30A for 120V, 277V, 240V, 208V WARNING BEFORE ATTEMPTING INSTALLATION OF THIS UN
PAGE 2
PLUMBING CONNECTIONS NOTE: ALL PLUMBING AND MOUNTING MUST BE COMPLETED BEFORE PROCEEDING WITH THE ELECTRICAL HOOK-UP. 1) The unit is supplied with 3/8’’ compression fittings. USE THESE: DO NOT USE THREADED PIPE FITTINGS. DO NOT USE PIPE DOPE OR TEFLON TAPE ON THIS INSTALLATION. Ensure the inlet filter supplied with this unit is in place. 2) Ensure that the pipes are correctly aligned with the inlet and outlet bosses to avoid excessive stress on the heater body molding of the unit. .
PAGE 3
GENERAL This “Single Point” water heating unit is specifically designed to be installed “under sink” feeding a SINGLE faucet. This unit is designed to take in cold water ONLY and heat it to temperatures suitable for hand washing. To obtain optimum performance and energy savings, the unit should be located as near as possible to the point of use. This unit incorporates a constant flow device and should only be used with the faucet aerator supplied.
PAGE 4
ELECTRICAL CONNECTIONS WARNING BEFORE BEGINNING ANY WORK ON THE ELECTRICAL INSTALLATION BE SURE THAT THE CIRCUIT BREAKER IS IN THE “OFF” POSITION TO AVOID ANY DANGER OF ELECTRICAL SHOCK. This water heating must have its own independent circuit using insulated, UL listed, 3 wire cable of the appropriate size suitable for use up to 75°C protected by the correctly rated circuit breaker.