Owner's Manual

ManualsBrandsBrandmotion ManualsCar Audio & VideoSUTV-8857

SummitView™ Jeep Wrangler (JK/JL)

Adjustable Rear Vision System

with Infrared Camera For Factory Display

SUTV-8857

Product Features

Install Time

Recommended Tools

1hr 30m - 2hr

Wrench

Socket SetScrew Driver Panel Removal Tool Zip Ties

Wire Strippers Wire Cutters Electrical Tape

Questions? Call the Brandmotion technical support line at (734) 619-1250 or CLICK HERE

Installation Instructions - SUTV-8857 Page 1/9AR_03_23_21

Summary of content (9 pages)

PAGE 1
SummitView™ Jeep Wrangler (JK/JL) Adjustable Rear Vision System with Infrared Camera For Factory Display SUTV-8857 Recommended Tools Product Features Wrench Wire Strippers Wire Cutters Electrical Tape Screw Driver Panel Removal Tool Zip Ties Socket Set Install Time 1hr 30m - 2hr Questions? Call the Brandmotion technical support line at (734) 619-1250 or CLICK HERE AR_03_23_21 Installation Instructions - SUTV-8857 Page 1/9
PAGE 2
Vehicle Application: Jeep Wrangler JK Part Number: SUTV-8857 Kit Contents Kit A Components for installing the SUTV-8857 Kit Contents: 1x Infrared Camera 1x Adjustable 5th Wheel Camera Mount 1x Video Chassis Harness 1x RCA to Factory 22 Pin connector 1x Flash Module 3x Push Nuts 15x Zipties AR_03_23_21 Installation Instructions - SUTV-8857 Page 2/9
PAGE 3
Vehicle Application: Jeep Wrangler JK Part Number: SUTV-8857 Programming Instructions 1. PLEASE NOTE: These modules are VIN locked for single vehicle use. If your vehicle ever needs a radio replaced or is flashed by a dealership, you can reprogram with this programmer. 2. Start the vehicle. Allow it to run for 20-30 seconds before proceeding. *Failure to start the vehicle before inserting the programming module can cause catastrophic failure of the module and void your warranty on this part. 3.
PAGE 4
Vehicle Application: Jeep Wrangler JK Part Number: SUTV-8857 6. Remove driver knee bolster cover 7. Remove (2) 7mm bolts on both sides of the steering column. 8. Remove center stack/cluster trim 9. Remove the glove box for access. You will need access to the area behind the glove box to make your connection to the radio. 10. Remove (4) 7mm bolts to remove radio from dash 6 8 9 10 11. Locate the White 22 pin connector with a female RCA that was included with your kit.
PAGE 5
Vehicle Application: Jeep Wrangler JK Part Number: SUTV-8857 Part 2 Camera functionality test (Highly recommended, not required) 1. 8837: a. There will be three wires accompanying the RCA: Red, Green, and Black 12V Power(Red+Green) 1. Twist red and green together = Power 2. Black = Ground b. Using an wire extension (not supplied) Ground (Black) 1. Connect twisted red and green directly to positive terminal of battery 2. Connect Black to negative terminal of battery c. Test Camera 1.
PAGE 6
Vehicle Application: Jeep Wrangler JK Part Number: SUTV-8857 Part 3 Installing Rear Camera on Tire Carrier 1. Remove your spare tire and place the camera bracket on the top two studs. 2. Secure bracket to carrier using (2) push nuts to secure the bracket on two top studs. 3. The nylon washer will go on the bottom stud and will be secured with the third push nut. 1 3 5 6 4. Place your tire on the carrier and make any needed adjustments to the camera placement to see through the wheel spokes. 5.
PAGE 7
Vehicle Application: Jeep Wrangler JK Part Number: SUTV-8857 5. Use supplied wire ties to secure chassis harness to exterior of fabric factory wire cover connecting tailgate to body. Do not run though fabric factory wire cover. CAUTION: Leave enough slack to allow the gate to open fully 6. Using a plastic trim removal tool, remove rear access (behind seat belt) panel to expose 10mm bolt, and remove bolt. Failure to remove this bolt will break the panel. 7. Remove interior rear quarter panel 8.
PAGE 8
Vehicle Application: Jeep Wrangler JK Part Number: SUTV-8857 c. Connect twisted red and green wire to power output from radio 12V Power (Red) d. Connect black wire to Chassis ground. We recommend using factory chassis grounding point. Ground (Black) 2. 8847: a. Identify red power wire exiting the back of the yellow RCA from your camera chassis harness b. Identify power output from your aftermarket radio c. Connect Red wire to power output from your aftermarket radio d.
PAGE 9
Vehicle Application: Jeep Wrangler JK Part Number: SUTV-8857 FAQ Section Installation of the Rear Vision Camera WARNING: Cancer and Reproductive Harm www.P65Warnings.ca.