Assembly Instruction

ManualsBrandsBreakwater Bay ManualsLightingMohonk Mottled Black 1 -Light 24.5'' H Hardwired Lantern Head

1of2

Package Contents

Mounting Screw

Fixture Body

Glass Panel

Fixture Hood

STEP 1 Install Glass Panels,

Bulb and Fixture Hood

A. Remove Allen screws and tabs

from the top edge of the cage

and the Fixture Body (D).

B. Insert Glass Panels (C) into

the slot in the bottom edge of

the cage and the Fixture Body

(D). Place tabs onto the top

edge of Glass Panels (C) and

align holes on tabs to

mounting holes on the top

edge of the cage and the

Fixture Body (D). Secure by

threading Allen screws back

into the cage and the Fixture

Body (D). Hand tighten until

snug with screwdrivers.

C. Insert the bulb onto the socket

and screw snugly into place.

D. Remove lock screws from the

bottom edge of the Fixture

Hood (B). Attach the Fixture

Hood (B) onto the top edge of

the Fixture Body (D) and

secure with removed lock

screws. Hand tighten until

snug with screwdrivers.

E. Rotate the curve metal until it

is just on the top of the Fixture

Hood (B).

Figure 1

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

(1)A21MediumBasebulb150WMaximumor

(1)MediumBaseVintagebulbisrecommendedbutnotsupplied.

20-30minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement

parts.

LightSource:

EstimatedAssembly Time:

Preparation:

ToolsRequired:Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

Curve Metal

Vintage Bulb

(recommended

but not supplied)

Slot

Socket

Allen Screw

Tab

STEP 2 - Mark the Location for the 3 Mounting Holes

A. Place the light fixture onto the post and mark the location of the 3

mounting holes on the fixture fitter onto the post with the marking

pen.

Fixture

Fitter

Marking Pen

Mounting

Hole

STEP 3 M C

EM H

- arking the enter of

ach ounting ole

A. Remove the light fixture. Using

the center punch and hammer

marking the center of each

mounting hole location that is

marked with the marking pen.

Center Punch

Hammer

Marking

Post Lighting

Post

STEP 4 Drill Holes-

A. Using the 1/16” bit and drill, drill a pilot hole completely through the

post at each (3) locations marked in step 5 above.

1/16” bit and drill

Post

Fixture

Fitter

Figure 2

Figure 3

Figure 4

Assembly Instruction Sheet

Summary of content (2 pages)

PAGE 1
Assembly Instruction Sheet Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (1) A21 Medium Base bulb 150W Maximum or (1) Medium Base Vintage bulb is recommended but not supplied. Estimated Assembly Time: 20-30 minutes Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to ensure all parts are present.
PAGE 2
STEP 5 - Wire Connections A. Use standard wire connectors (not included) to make all wire connections. Twist connectors until wires are tightly joined together. Wrap each connection with approved electrical tape and carefully stuff all the connected wires into the Outlet Box. White wire from outlet box White wire from fixture Black wire from outlet box (or Red) Black wire from fixture Bare, or Green Ground wire from outlet box FINISH: MOTTLED BLACK 8.5” 8.