INSTALLATION GUIDE HB0111 BDF SERIES ! INTENDED FOR DOMESTIC COOKING ONLY ! READ AND SAVE THESE INSTRUCTIONS INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER. HOMEOWNER: USE AND CARE INFORMATION ON PAGES 9-10. Broan-NuTone Canada ULC; Mississauga, Ontario 1-877-896-1119 www.broan.ca REGISTER YOUR PRODUCT ON LINE AT: www.broan.com/register 30042454 rev.
IMPORTANT SAFETY INSTRUCTIONS ! WARNING ! TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSON(S), OBSERVE THE FOLLOWING: WARNING TO REDUCE THE RISK OF INJURY TO PERSON(S) IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING*: 1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in the warranty. 2.
ABOUT THIS MANUAL Please take note this manual uses the following symbols to emphasize particular information: ! WARNING Identifies an instruction which, if not followed, might cause serious personal injuries including possibility of death. CAUTION Denotes an instruction which, if not followed, may severly damage the unit and/or its components. NOTE: Indicates supplementary information needed to fully complete an instruction. TABLE OF CONTENTS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. INSTALL DUCTWORK . . . .
2. PREPARE INSTALLATION ! WARNING When performing installation, servicing or cleaning the unit, it is recommended to wear safety glasses and gloves. Tools needed to install the range hood: - Phillips screwdriver no.
3. PREPARE THE HOOD 3.1 ALL INSTALLATIONS 1. Lay the hood on its top on a table. Use a piece of cardboard to avoid damaging the table or the hood. Slide the main grease cup out and set aside. Remove the bottom panel 7 retaining screws. Set bottom panel and screws aside. SCREW LOCATIONS GREASE CUP HO0173 HO0046 SCREW LOCATIONS 2. Remove both electrical box cover retaining screws. Remove cover and set aside with screws.
3. PREPARE THE HOOD (CONT'D) 3.3 HORIZONTAL DISCHARGE ONLY 1. Remove the large shutoff plate 5 retaining screws located on the BACK of the hood. Discard the shutoff plate and its screws. HO0049 2. Remove the small shutoff plate 10 retaining screws located INSIDE the back of the hood. Set the screws aside and discard the shutoff plate. HO0048 3. Using the 10 screws previously removed in step 2, install the adapter in the inside back of the hood. HJ0005 4.
5. CONNECT WIRING ! WARNING Risk of electrical shock. Electrical wiring must be done by qualified personnel in accordance with all applicable codes and standards. Before connecting wires, switch power off at service panel and lock service disconnecting means to prevent power from being switched on accidentally. 1. Connect cable to range hood wiring using included wire connectors. Connect BLACK to BLACK, WHITE to WHITE and GREEN or BARE wire to GREEN wire. 2.
6. LIGHT BULBS ! WARNING Make sure power is switched off at service panel before carrying out any operation on the hood. This range hood requires two UL approved halogen bulbs (JC type, 12 V, 20 W, G4-base), included. To replace bulbs: CAUTION Take care not to damage the hood finish while using the screwdriver. 1. Carefully insert the blade of a small flat blade screwdriver between light cover and rim and gently pry out light assembly.
7. CLEANING AND MAINTENANCE 1. Slide out main grease cup. 1 HO0171 2. Disengage the small grease guard cups from the metal guards by turning counterclockwise and remove. 3. Remove the screw retaining the metal guards to the hood. 4. Remove the metal guards from the hood. Then remove the bottom panel. 3 2 HD0142 4 HD0143 HD0144 5. Unscrew the clips and remove the wheel grease collector. 6. Remove the wheel center cap. 7.
7. CLEANING AND MAINTENANCE (CONT'D) STAINLESS STEEL CLEANING: Do: • Regularly wash with clean cloth or rag soaked with warm water and mild soap or liquid dish detergent. • Always clean in the direction of original polish lines. • Always rinse well with clear water (2 or 3 times) after cleaning. Wipe dry completely. • You may also use a specialized household stainless steel cleaner. Don’t: • Use any steel or stainless steel wool or any other scrapers to remove stubborn dirt.
9. WIRING DIAGRAM KEY SWITCH CONTROL PANEL 12 V /20 W X 2 WHITE YELLOW M BLACK WHITE BLUE GREY BLACK BROWN BLUE BLACK BROWN GREY NEUTRAL GROUND YELLOW M C GREEN C LINE WHITE WHITE BLACK LAMPS HE0112A GREEN GREEN 10. SERVICE PARTS KEY NO. PART NO. DESCRIPTION QTY.
11. WARRANTY BROAN-NUTONE CANADA ULC One Year Limited Warranty Broan-NuTone Canda warrants to the original purchaser of its products that such products will be free from defects in material and workmanship for a period of one (1) year from the date of original purchase. THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.