INSTALLATION INSTRUCTIONS HB0073 E60000LC SERIES ! INTENDED FOR DOMESTIC COOKING ONLY ! READ AND SAVE THESE INSTRUCTIONS INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER. HOMEOWNER: USE AND CARE INFORMATION ON PAGES 13 & 14. Venmar Ventilation ULC; Drummondville, Québec www.broan.ca 877-896-1119 REGISTER YOUR PRODUCT ONLINE AT: www.broan.ca 21241 rev.
! WARNING ! TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: WARNING TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING*: 1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in the warranty. 1. SMOTHER FLAMES with a close-fitting lid, cookie sheet or metal tray, then turn off the burner.
- E60000LC SERIES RANGE HOOD SYSTEM INTERNAL BLOWERS MODEL 437 (HIGH CAPACITY ROOF CAP) MODEL 647 (7" ROUND WALL CAP) MODEL 441 (10" ROUND WALL CAP) MODEL 418 (10" ROUND ADJUSTABLE ELBOW) MODEL 421 (10" ROUND VERTICAL IN-LINE DAMPER) MODEL 634 OR 644 (ROOF CAP) MODEL 415 (7" ROUND ADJUSTABLE ELBOW) MODEL 643 (8" ROUND WALL CAP) 8" ROUND ADJUSTABLE ELBOW MODEL 407 (7" ROUND — 2 FT. SECTIONS) MODEL 410 (10" ROUND DUCT — 2 FT.
- E60000LC SERIES RANGE HOOD SYSTEM IN-LINE AND EXTERIOR BLOWERS MODEL 437 (HIGH CAPACITY ROOF CAP) MODEL 643 (8" ROUND WALL CAP) MODEL 441 (10" ROUND WALL CAP) MODEL HLB9 (800 CFM) OR HLB11 (1100 CFM) IN-LINE BLOWER (INCLUDES TWO 8" X 12" TO 10" ROUND TRANSITIONS) MODEL 335 (1200 CFM) OR 336 (1500 CFM) EXTERIOR BLOWER MODEL 331H (600 CFM) OR 332H (900 CFM) EXTERIOR BLOWER MODEL 441 (10" ROUND WALL CAP) MODEL HLB6 (660 CFM) IN-LINE BLOWER (INCLUDES TWO 4½" X 18½" TO 10" ROUND TRANSITIONS) MODEL 421 (1
1. SELECT BLOWER OPTION The Broan Elite E60000LC Series range hood includes many configurations: hoods with single or double internal blowers (included with the hood), or hoods using external blowers. For this last category, the Broan Elite E60000LC Series must be installed with in-line blower models HLB3, HLB6, HLB9 or HLB11, or exterior blower models 331H, 332H, 335 or 336 only. Other blowers cannot be substituted (blowers sold separately). Plan where and how the ductwork will be installed.
2. MEASURE INSTALLATION Dimensions for the most common installation are illustrated at right. Ceiling The minimum hood distance above cooktop is 24" for electric ranges, and 30" for gas ranges. A maximum of 30" above cooktop is highly recommended for best capture of cooking impurities. Distances over 30" are at the installer and users discretion.
3. PREPARE THE INSTALLATION (CONT’D) Cut-out the openings for duct (A) and power cable (B), in cabinet or wall, according to the direction of discharge chosen. See figures below. NOTE: For all internal blower hoods, the cut-out opening for house wiring can be made in cabinet bottom OR wall, no matter the discharge chosen (vertical or horizontal).
5. CHOOSE THE OPENING(S) (INTERNAL BLOWER(S) HOOD ONLY) Remove the knockout(s) for the chosen opening(s) (horizontal at the back of the hood or vertical on top). See illustrations below. 1 2 3 1 2 3 VERTICAL DISCHARGE HORIZONTAL DISCHARGE HR0021 A B Punch out the appropriate electrical knockout hole on top (A) or back (B) of the hood. Install the wire clamp (included in parts bag). HD0250 6.
8. HORIZONTAL DISCHARGE INSTALLATION (INTERNAL BLOWER(S) HOOD ONLY) All internal blower hoods are factory shipped with the blower(s) mounted for a vertical discharge configuration. For a horizontal discharge configuration, disassemble the blower(s) from the inner top of the hood and mount it (them) to the inner back panel of the hood. The procedure below applies for one or two blowers.
9. INSTALL THE ADAPTER AND THE TRANSITION (IF NEED BE) (INTERNAL BLOWER(S) HOOD ONLY) Using standard 3/8" screws provided, secure the adapter to the top (or back) of the hood (2 screws for a 3¼" x 10" adapter/damper and 4 screws for a 4½" x 18½" adapter). Seal the adapter to the hood using metal foil duct tape. For round ducting, install an appropriate sized transition and seal the joints with metal foil duct tape. HJ0013 10.
12. INSTALL THE HOOD CAUTION Hold the hood until it is completely secured to the wood mounting strip. MOUNTING SCREWS LOCATION INTERNAL BLOWER(S) ONLY Run power cable to installation location. Remove the electrical compartment cover. Insert the cable in the hood and tighten the wire clamp to secure the cable. HD0579 ALL INSTALLATIONS WALL ANCHORS LOCATION Rest the back cavity of the hood against the wood mounting strip. Secure the hood to wood mounting strip with 4 screws no.
15. INSTALL THE BLOWER (EXTERIOR OR IN-LINE BLOWER) Refer to instructions included with blower. Plug the 3-prong plug cord from rough-in plate to the 3-prong male connector inside the hood (A) and the 2-prong male connector cord from rough-in plate to the 2-prong plug inside the hood (B). ! B A WARNING Do not plug both cords together. HE0078 16. REINSTALL GREASE DRIP RAIL AND BAFFLE FILTERS Reinstall grease drip rail.
18. USE AND CARE Baffle Filters The baffle filters should be cleaned frequently. Use a warm detergent solution. Wash often if your cooking style generates a lot of grease— like frying food or wok cooking. Remove baffle filters by pushing them towards the back of hood and rotating filters downward. Baffle filters are dishwasher safe. Allow filters to dry completely before reinstalling them in the hood. You may clean all-metal filters in the dishwasher using a non-phosphate detergent.
19. OPERATION (CONT'D) 1) LED lighting knob 2) Blower operation indicator 3) ON/OFF blower switch 4) Blower speed control knob 3 4 2 HC0073 1 A A) LED lighting knob B) Blower speed control knob B HC0035 COOKTOP LIGHTING The LED lighting of this hood is controled by a rotary dimmer switch (1). The lighting turns on at high intensity, and decreases as the knob is turned clockwise.
21.
22. SERVICE PARTS Broan Elite E60000LC Single or double internal blower hoods Broan Elite E60000LC Series Exterior or In-Line blower hoods 1 15 15 14 14 2 2 13 11 12 3 4 4 3 11 10 18 13 12 17 10 16 5 6 6 7 7 8 HL0236 KEY NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 * * HL0237 QTY. (HOOD WIDTH) PART DESCRIPTION NO.