Manual

ManualsBrandsBrocks Performance ManualsCarShortMeg 2 Full System 14" Muffler S1000RR (10-14)

DOCUMENT ID 994406

Page 1 of 4

Installation Instructions for the

BMW S 1000 RR (2010) Alien Head and Short Meg Exhaust System

CHECK PACKAGE CONTENTS

1. Four (4) Header Mount Flanges (Installed in Headers)

2. One (1) Left Side Header (Cylinders 1 & 2)

3. One (1) Right Side Header (Cylinders 3 & 4)

4. One (1) Collector (Y-Pipe)

5. One (1) Alien Head or Short Meg Muffler

6. One (1) Package Containing Springs, Spring Puller, Bracket and

Hardware

7. One (1) Instruction Package

If any parts are missing, contact Brock’s Performance Products.

Brock’s Performance Alien Head

PRE-ASSEMBLE HEADERS AND COLLECTOR TO ENSURE PROPER FIT BETWEEN ALL PARTS

Brock’s Performance carefully inspects

each system prior to shipping, we

recommend that you test fit your system

prior to installation. Apply WD-40 to the

joints to ease assembly, adjustment,

and/or disassembly.

REMOVE BODYWORK

Consult a factory service manual for additional information. To

remove the left lower fairing, remove the five (5) mounting bolts from

the inside and bottom of the lower fairing pointed at by the red

arrows. Remove the seven (7) mounting bolts from the outside of the

lower fairing in the red circles. Remove the one (1) plastic fastener in

the green circle by unscrewing the center pin then pulling the

fastener out. Pull out on the fairing to detach from the push pin

pointed at by the green arrow. Pull the fairing out just far enough to

access the turn signal wire located on the top of the radiator mount

and unplug. The left lower fairing can now be removed.

Brock’s Performance Products • 4064 East Patterson Road • Dayton, OH 45430 • Phone: 937-912-0054 • Fax: 937-912-0062

Summary of content (4 pages)

PAGE 1
DOCUMENT ID 994406 Brock’s Performance Products • 4064 East Patterson Road • Dayton, OH 45430 • Phone: 937-912-0054 • Fax: 937-912-0062 Installation Instructions for the BMW S 1000 RR (2010) Alien Head and Short Meg Exhaust System CHECK PACKAGE CONTENTS 1. 2. 3. 4. 5. 6.
PAGE 2
DOCUMENT ID 994406 To remove the right lower fairing, remove the four (4) mounting bolts from the inside and bottom of the lower fairing pointed at by the red arrows. Remove the seven (7) mounting bolts from the outside of the lower fairing in the red circles. Remove the one (1) plastic fastener in the green circle by unscrewing the center pin then pulling the fastener out. Pull out on the fairing to detach from the push pin pointed at by the green arrow.
PAGE 3
DOCUMENT ID 994406 room for the removal of the headers. Remove all eight (8) of the mounting nuts holding the four primaries to the head. Remove the two (2) bolts mounting the catalytic converter to the frame and the four (4) bolts securing the brackets to the catalytic converter. Drop the catalytic converter down to clear the frame, move the system forward to disengage the primary pipes from the cylinder head and remove from the bike.
PAGE 4
DOCUMENT ID 994406 RE-INSTALL RADIATOR / OIL COOLER BRACKET Re-attach the radiator / oil cooler bracket, two (2) “E” clips and washers in the bottom of the radiator and oil cooler. Insert one (1) bolt to the crankcase to fasten bracket and tighten. CLEAN SYSTEM OF FINGER PRINTS With any exhaust system you must clean all finger prints off before starting the motorcycle to insure there will not be finger prints “burned” into the pipe. Carefully use alcohol, brake clean, etc. to clean the system.