User`s guide
Table Of Contents
- SOFTWARE USER’S GUIDE
- Table of Contents
- 1 Using the machine as a printer
- Using the Brother printer driver
- How to print your document
- Simultaneous printing and faxing
- Printer operation key
- Printer driver settings (For Windows®)
- How to access the printer driver settings (For Windows®)
- Features in the PCL printer driver (For Windows®)
- Features in the PS (PostScript®) Brother printer driver (MFC-7225N and MFC-7820N only) (For Windows®)
- Status Monitor (Windows® only)
- 2 How to scan using Windows®
- Scanning a document using WIA driver (For Windows® XP only)
- Scanning a document using the TWAIN driver
- Using the Scan key (For USB or Parallel cable users)
- Using ScanSoft® PaperPort® 9.0SE and OmniPage® OCR
- 3 Using ControlCenter2.0 (For Windows®)
- 4 Using MFC Remote Setup (For Windows®) (not available for DCP-7020)
- 5 Using Brother PC-FAX software (For Windows®) (not available for DCP-7020)
- PC-FAX sending
- Speed-Dial setup
- Brother Address Book
- Setting up a Member in the Address Book
- Setting up a Group for Broadcasting
- Editing Member information
- Deleting a Member or Group
- Exporting the Address Book
- Importing to the Address Book
- Sending a file as a PC-FAX using the Facsimile style user interface
- Sending a file as a PC-FAX using the Simple style user interface
- Setting up PC-FAX receiving
- 6 Network Scanning (For Windows®) (MFC-7225N, MFC-7820N or models with the optional NC-2200w Only)
- 7 Using your machine with a Macintosh®
- Setting up your USB-equipped Apple® Macintosh®
- Using the Brother printer driver with your Apple® Macintosh® (Mac OS® X)
- Using the Brother printer driver with your Apple® Macintosh® (Mac OS® 9.1 to 9.2)
- Using the PS driver with your Apple® Macintosh® (MFC-7225N and MFC-7820N only)
- Sending a fax from your Macintosh® application (not available for DCP-7020)
- Scanning from a Macintosh®
- Configuring Network Scanning
- Using Presto!® PageManager®
- Using ControlCenter2.0 (For Mac OS® X 10.2.4 or greater)
- MFC Remote Setup (Mac OS® X 10.2.4 or greater) (not available for DCP-7020)
- Index
- brother USA/CAN
Using the machine as a printer
1 - 2
1
Printing from the manual feed slot
Note
■
The machine automatically turns on the Manual Feed mode when you put paper in the manual feed slot.
■
The machine illustrations are of the MFC-7420 or MFC-7820N, but the descriptions apply to all the
models.
1
Set the
Paper Size
,
Media Type
,
Paper Source
, and other settings in the printer driver.
Set the
Paper Source
to
Manual
.
2
Slide the paper guides to fit the paper size.
3
Using both hands put paper in the manual feed slot until
the front edge of the paper touches the paper feed roller.
Hold the paper in this position until the printer
automatically feeds it in for a short distance, and then let
go of it.
4
Send the print data to the machine.
Note
■
Put the paper into the manual feed slot with the side to be printed face up.
■
Make sure that the paper is straight and in the proper position on the manual feed slot. If it is not, the paper
may not be fed properly, resulting in a skewed printout or a paper jam.
■
Do not put more than one piece of paper in the manual feed slot at any one time, as it may cause a jam.
5
After the printed page comes out of the machine, put in the next sheet of paper as in Step 3 above.
Repeat for each page that you want to print.