User Manual
Table Of Contents
- Quick Setup Guide MFC-J6510DW MFC-J6710DW
- Start Here
- 1 Unpack the machine and check the components
- 2 Load plain A4 paper
- 3 Connect the power cord and telephone line
- 4 Set your country (Australia and New Zealand only)
- 5 Install the ink cartridges
- 6 Check the print quality
- 7 Set the paper settings
- 8 Wireless setup (if needed)
- 9 Choose your language (if needed) (Not available in Australia and New Zealand)
- 10 Choose a Receive Mode
- 11 Set the date and time
- 12 Enter personal information (Station ID)
- 13 Fax Transmission Report
- 14 Set Tone or Pulse dialling mode (Not available in New Zealand)
- 15 Set the telephone line compatibility
- 16 Manual Feed Slot
- 17 Choose your connection type
- For USB interface users (Windows® 2000 Professional/XP Home/XP Professional/Windows Vista®/Windows® 7)
- For USB interface users (Mac OS X 10.4.11, 10.5.x, 10.6.x)
- For wired network interface users (Windows® 2000 Professional/XP Home/XP Professional/Windows Vista®/Windows® 7)
- For wired network interface users (Mac OS X 10.4.11, 10.5.x, 10.6.x)
- For wireless network interface users
- 18 Before you begin
- 19 Choose your wireless setup method
- 20 Manual setup from the control panel using the Setup Wizard (Macintosh, Mobile Devices and Windows®)
- 20 One-push Setup using WPS or AOSS™ (Windows® and Macintosh)
- Troubleshooting
- Install the drivers & software (Windows® 2000 Professional/XP Home/XP Professional/Windows Vista®/Windows® 7)
- Install the drivers & software (Mac OS X 10.4.11, 10.5.x, 10.6.x)
- Install Optional Applications Windows®
- For Network Users
- Consumables
- brother ARL/ASA/NZ
- Start Here
27
For Wireless Network Users
Wireless Network
20
One-push Setup using
WPS or AOSS™
(Windows
®
and
Macintosh)
a Confirm your wireless access point/router has
the WPS (Wi-Fi Protected Setup) or AOSS™
symbol as shown below.
b Place the Brother machine within range of your
WPS or AOSS™ access point/router. The
range may differ depending on your
environment. Refer to the instructions provided
with your access point/router.
If you began the configuration from step 8 on
page 8, go to d.
All other users go to c.
c On your machine, press Menu.
Press a or b to choose Network and press
OK.
Press a or b to choose WLAN and press OK.
d Press a or b to choose WPS/AOSS and press
OK.
When Network I/F switched to
Wireless is displayed, press OK to accept.
This will start the wireless setup wizard.
e When the LCD shows Start WPS or AOSS,
press the WPS or AOSS™ button on your
wireless access point/router. See the user’s
guide for your wireless access point/router for
instructions.
Then press OK and your machine will now
automatically detect which mode (WPS or
AOSS™) your wireless access point/router
uses and try to connect to your wireless
network.
f A connection result message appears for
60 seconds on the LCD and a wireless LAN
report will automatically be printed.
If the connection failed, check the error code on
the printed report and refer to Troubleshooting
on page 28.
Wireless setup is now complete. A four
level indicator on the bottom of your
machine’s LCD will show the wireless
signal strength of your access
point/router.
To install MFL-Pro Suite, continue to
step 21.
For Windows
®
Users:
Now go to
Page 30
For Macintosh Users:
Now go to
Page 34
Note
If your wireless access point/router supports WPS
(PIN Method) and you want to configure your
machine using the PIN (Personal Identification
Number) Method, see Using the PIN Method of
Wi-Fi Protected Setup in the Network User’s
Guide.