USER GUIDE Read Before Use! series RCT 526 www.BulletTools.com • 208-772-0175 RCT 520 PRT-INS-5RCT.RevA.11.
WARNING: FAILURE TO FOLLOW THIS GUIDE MAY RESULT IN SERIOUS INJURY! USING THIS MACHINE WITH RESPECT AND CAUTION WILL CONSIDERABLY REDUCE THE RISK OF PERSONAL INJURY. SAFETY GUIDE FOR THE MAGNUM™ RCT Series 1 �����READ AND UNDERSTAND THIS INSTRUCTION MANUAL BEFORE OPERATING THE RCT. 2 �����If you are not thoroughly familiar with the operation of the RCT Shear, obtain advice from a qualified instructor or call 800-406-8998 (Intl.: 208-772-0175). 3 �����Stay alert.
520 Set up Welcome! Your MAGNUM RCT SHEAR Comes ready to assemble.* *You will need #2 & #3 Phillips head screwdrivers and a 1/2” (13mm) socket or wrench. Please Review and Verify Parts Included in Box: 1. Power Assembly 1a. Safety Lock pin 2. Handle Assembly 3. Table 4. Tail 5. Rails (2) 6. Angle Guide 7. Hone Stone 8. Hardware Kit F. 1a. 2. 6. D. 1. 4. H. E. A. C. 3. 7. Hardware kit: Item A. Item B. Item C. Item D. Item E. Item F. Item G. 5. B.
526 Set up Welcome! Your MAGNUM RCT SHEAR Comes ready to assemble.* *You will need #2 & #3 Phillips head screwdrivers and a 1/2” (13mm) socket or wrench. Please Review and Verify Parts Included in Box: 1. Power Assembly 1a. Safety Lock pin 2. Handle Assembly 3. Table 4. Tail 5. Rails (4) 6. Angle Guide 7. Hone Stone 8. Hardware Kit 1a. F. 2. D. 1. 7. G. A. 4. C. E. 3. 7. Hardware kit: Item A. Item B. Item C. Item D. Item E. Item F. Item G. 5. B.
Set Up 3. Attach Table 3 3A 3B Item E A. Attach front of table to base, using Item D screws. Tighten with #3 Phillips. B. Attach back of table to tail using Item E self tapping screws. Tighten with #2 Phillips. 4. To Attach Handle: Tail Item D 4 Item F Insert Item F screws and tighten with 1/2” (13mm) wrench. Note: To ensure correct alignment, start each of the bolts by hand before using wrench. 5. attach angle Guide 5 Install angle guide and tighten Item G thumbscrew.
MAKING CUTS Caution! Wear hand and eye protection while operating the EZ Shear™ 1 While gently pushing handle down, pull Safety Lock pin out, then lift handle. Pull Safety Lock pin 2 Place product on table. Bring handle down until blade touches material. 3 Push the handle down until the material is completely cut. DO NOT USE ON HIGH PRESSURE LAMINATE OR SOLID WOOD! Warning! Blade is very sharp. Keep fingers away from blade. Most materials listed on page (6) shear cleanly with just one cut.
Your RCT Shear cuts a wide variety of products. Please refer to this cut guide for recommended products and thicknesses. RCT CUT GUIDE MAINTENANCE Honing the Blade 520 Maximum Thickness = 15mm or 5/8” 526 Maximum Thickness = 25mm or 1” Material Carpet Tile Commercial Vinyl Tile Luxury Vinyl Tile Parquet PVC Tile Hone every 100 cuts Push the handle down until blade is 1/4” (6mm) open. Lay the hone stone against the flat face of the blade (side toward the table). Slide from end to end 2 or 3 times.
WARRANTY 30 Day Satisfaction Guarantee Bullet Tools™ is confident that you will be absolutely pleased with the purchase of our product. If, for any reason, you are not completely satisfied with your tool, we will refund your purchase price at any time within 30 days of your original purchase (receipt required). If you want to return your product under our 30-day no risk trial offer (valid only for purchases made in the US), please contact us at 1-800-406-8998 or 208-772-0175 for return instructions.
