ThermoFresh® Servers GEN3 Style with Mechanical or Digital Sight Gauges 1 Gal (3.8L) or 1.5 Gal (5.7L) Capacity USE & CARE INFORMATION CAUTION: CLEAN AND SANITIZE YOUR SERVER BEFORE USING. SEE NOTE #1 of DAILY CLEANING. Bunn-O-Matic Corporation Post Office Box 3227, Springfield, Illinois 62708-3227 Phone (217) 529-6601 | Fax (217) 529-6644 54923.0000 G 8/20 © 2018 Bunn-O-Matic Corporation www.bunn.
BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTY Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows: 1) Airpots, thermal carafes, decanters, GPR servers, iced tea/coffee dispensers, MCR/MCP/MCA single cup brewers, thermal servers and ThermoFresh® servers (mechanical and digital) 1 year parts and 1 year labor. 2) All other equipment - 2 years parts and 1 year labor plus added warranties as specified below: a) Electronic circuit and/or control boards - parts and labor for 3 years.
CE REQUIREMENTS • This appliance must be installed in locations where it can be overseen by trained personnel. • For proper operation, this appliance must be installed where the temperature is between 5°C to 35°C. • Appliance shall not be tilted more than 10° for safe operation. • An electrician must provide electrical service as specified in conformance with all local and national codes. • This appliance must not be cleaned by water jet.
INTRODUCTION This server is intended for use with a BUNN® DUAL® TF DBC®, SINGLE® TF DBC® or ICB family brewers. When proper precautions are followed, 1.0 up to 1.5 gallons of coffee may be brewed directly into the server and then transported to a remote serving location. The server must be placed on a sturdy counter or shelf. NOTE: Calibration of the brewer is required prior to the use of the Digital TF Server. USER NOTICES The notices on this server should be kept in good condition.
DAILY CLEANING CAUTION: CLEAN AND SANITIZE YOUR SERVER DAILY NOTE: Bunn-O-Matic recommends the three step method for cleaning and sanitizing the server. The 3 step method consists of hot soapy water using an mild, non-citrus detergent, a fresh water rinse and an aqueous sanitizing solution using a non-chlorine sanitizer. Do not submerge the server. Failure to follow the recommended cleaning procedures can cause corrosion to the stainless steel surface and damage the vacuum seal.
SERVERS WITH STAND - Mechanical Sight Gauge 1 REPLACEMENT PARTS 53905.0001 Cap 54489.0001 Lid, 1.0 gal 54489.0000 Lid, 1.5 gal 3. 54938.0000 Decal, Do Not Submerge/Do Not Spray 4. 54086.1000 Top Cover with Handle and decal 42761.0001 Screw, Pan Head M4 x 9 5. 54470.0000 Plug 6. 54472.0000 Slide, Shroud 7. 54080.0002 Shroud, 1.0 gal 54080.0001 Shroud, 1.5 gal 8. 54530.0010 Tube, Sight Glass, 1.0 gal 54530.0009 Tube, Sight Glass, 1.5 gal 9. 53911.0000 Seal, Sight Gauge 10. 28526.1000 Tube, Silicone .
SERVERS WITH STAND - Digital Sight Gauge REPLACEMENT PARTS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22 23. 24. 25. 26. 27. 28. 53905.0001 Cap 53912.1000 DSG Lid Assy, 1.0 gal (Includes items 1 & 27) 53912.1001 DSG Lid Assy, 1.5 gal (Includes items 1 & 27) 39043.0003 Decal, Do Not Submerge Server 54938.0000 Decal, Do Not Submerge/Do Not Spray 54086.1000 Top Cover with Handle and decal 54470.0000 Plug 54468.0000 Backer, Badge 02367.0000 Screw 54925.0000 Badge, Logo 28526.
DIGITAL DISPLAY The Digital Sight Gauge (DSG) senses liquid levels and monitors hold times. Horizontal bars indicate the liquid level. The 1.0 gallon sensor displays a total of 4 bars and the 1.5 gallon sensor displays 6 bars. Each bar represents approximately 32 ounces of liquid. All bars will be displayed when the server is full. As liquid is dispensed the number of bars displayed decreases beginning with the upper most bar. When the server is close to empty no bars are displayed.
PROGRAMMING A 10 position rotary switch is used to view and change the configuration parameters. The rotary switch is accessible when the battery cover and holder are removed. Run 1 Increment 3 7 Select 2 8 9 0 Value 4 Decrement 5 6 Position 0 Run – This is the normal rotary switch setting and allows the DSG to run with the given configuration. The rotary switch must be in this position for normal operation.
BATTERY REPLACEMENT The Digital Sight Gauge lid comes equipped with 4 AAA batteries. The batteries have a use life of approximately 1½ years under normal operating conditions. NOTE: Batteries are not covered under product warranty. To replace the batteries: 1. Remove the lid assembly from the server. 2. Remove the two screws and cover on bottom of the lid, Fig 2. 3. Replace used batteries with 4 AAA alkaline batteries. 4. Replace cover and two screws. 5. Replace lid assembly. FIG.
