Owner's Manual

ManualsBrandsBunn ManualsCoffee GrinderG9-2T HD

SONAL INJURY

HAZARD.

KEEP FINGERS

AND

FOREIGN OBJECTS

OUT OF

HOPPER

OR CHUTE OPENING.

CAUTION

PERSONA

INJURY

HAZARD.

KEEP FINGERS

AND

FOREIGN OBJECTS

OUT

OF HOPPER

OR CHUTE OPENING.

CAUTION

G9-2 HD

G9-2T HD

G9-2 HD-S

INSTALLATION & OPERATING GUIDE

BUNN-O-MATIC CORPORATION

POST OFFICE BOX 3227

SPRINGFIELD, ILLINOIS 62708-3227

PHONE: (217) 529-6601 FAX: (217) 529-6644

To ensure you have the latest revision of the Operating Manual, or to view the Illustrated Parts

Catalog, Programming Manual, or Service Manual, please visit the Bunn-O-Matic website, at

www.bunn.com. This is absolutely FREE, and the quickest way to obtain the latest catalog and

manual updates. For Technical Service, contact Bunn-O-Matic Corporation at 1-800-286-6070.

Summary of content (8 pages)

PAGE 1
G9-2 HD G9-2T HD G9-2 HD-S N IO N IO UT RY CA INJU AL . ON RD D RS ZA AN PE HA ERS CTS NG JE FI OB ER EP N PP G. KE REIG HO ENIN FO T OFE OP OU UT CH OR UT RY CA INJU AL . ON RD D RS ZA AN PE HA ERS CTS JE FINGOB ER EP N PP G.
PAGE 2
BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTY Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows: 1) Airpots, thermal carafes, decanters, GPR servers, iced tea/coffee dispensers, MCP/MCA pod brewers thermal servers and Thermofresh servers (mechanical and digital)- 1 year parts and 1 year labor. 2) All other equipment - 2 years parts and 1 year labor plus added warranties as specified below: a) Electronic circuit and/or control boards - parts and labor for 3 years.
PAGE 3
CONTENTS Introduction...................................................................... 3 User Notices...................................................................... 3 Electrical Requirements.................................................... 4 CE Requirements.............................................................. 4 Operating Controls............................................................ 4 Initial Set-Up.....................................................................
PAGE 4
ELECTRICAL REQUIREMENTS This grinder has an attached cordset and requires 2-wire, grounded service rated 120 volts ac, 15 amp, single phase, 60 Hz for 120V models and 230 volts ac, 10 amp single phase, 50 Hz for 230V models.. CE REQUIREMENTS • This appliance must be installed in locations where it can be overseen by trained personnel. • For proper operation, this appliance must be installed where the temperature is between 5°C to 35°C. • Appliance shall not be tilted more than 10° for safe operation.
PAGE 5
INITIAL SET-UP 1. Open the top lid. Clear all foreign objects and shipping material from the hopper compartment and the entrance to the grind chamber. 2. Remove the lower front inspection panel. 3. Plug-in the grinder. 4. Select either the right or left hopper with the selector switch. Do not press the start switch. 5. If grinder has an analog timer, proceed to step 6. If grinder has a digital timer, momentarily press the center (DISPLAY) button on the dispense timer panel.
PAGE 6
COFFEE GRINDING STEP 1 P597 STEP 2 P598 STEP 3 P599 STEP 4 P600 P601 STEPS 5 & 6 1. 2. 3. 4. Visually inspect the selected hopper for an ample supply of whole bean coffee. Place a paper filter into the brew funnel. The filter must not be folded-over or tilted to one side. Insert the funnel into the funnel rails and push until it stops. Momentarily press the start switch. The grinding action will stop automatically after the preset amount of ground coffee is dispensed into the funnel. 5.
PAGE 7
ADJUSTMENTS The grind can be set from very fine to very coarse. The amount may be adjusted for use in most commercial coffee brewers. The following procedures should be used to make adjustments. A change in the burr adjustment will also change the amount dispensed. Any adjustment of the burrs should be followed by an adjustment of the timer. RSE - FIN Burr Adjustment E OA C 1. Unplug the grinder and empty all beans from the hoppers. 2.
PAGE 8
ADJUSTMENTS (cont.) 3. Use the table on the next page to find approximate timer setting for the grind and amount of coffee desired. 4. Plug-in the grinder. Select either the right or left hopper with the selector switch. Do not press the start switch. 5. If grinder has an analog timer, proceed to step 6. If grinder has a digital timer, momentarily press the center (DISPLAY) button on the dispense timer panel.