User Manual

ManualsBrandsBurkert ManualsAccessories for waterType 6017

Operating Instructions Type 6017

Design:

2-way solenoid valve, direct acting, normally closed (Circuit

function A).

Seal Materials and Fluids handled:

See Table 1.

Fluid and Ambient Temperature:

For Hazardous Locations Div. 1 (T4 rated)

Max. Ambient Temperature 104 °F (40 °C)

Max. Fluid Temperature 194 °F (90 °C)

The UL-listed valve for Hazardous Locations is suitable for the

fluids air, inert gas, water and gasoline.

For Hazardous Locations Div. 1 (T6 rated)

Max. Ambient Temperature 104 °F (40 °C)

Max. Fluid Temperature 140 °F (60 °C)

For Intrinsically Safe Apparatus for use in Class I, II and III,

Division 1 Hazardous Locations (T6 rated)

Max. Ambient Temperature 140 °F (60 °C)

Max. Fluid Temperature 140 °F (60 °C)

For Hazardous Locations Div. 2 and Ordinary Locations:

See Table 1.

Pressure Range:

Maximum inlet pressure see label on valve.

Installation:

Before installing valve ensure that piping etc. is free of foreign

matter (metal shavings, pipe sealing materials, welding scale

etc.). Installation as required but preferable with coil uppermost.

Installation in this position tends to prevent foreign matter

remaining in core tube (increased life). Do not put any loads on

coil unit.

PTFE tape is recommended for sealing ports. Mounting is

accomplished by means of four M4 x 8 mm tapped holes

located on the valve underside. Letters on valve body indicate

pressure por t, exhaust and outlet of the valve.

Marking (example):

Body Material

BR = Brass

SS = Stainless Steel

Seal Material

EPDM = EPDM

NBR = NBR

FKM = FKM

Circuit function

A = Normally Closed

Item No.

Voltage / Frequency / Power Consumption

Maximum Pressure

Approvals

The valve is either approved as

General Purpose valve for Hazardous Locations

Class I, Division 1, Group A, B, C, D

Class II, Division 1, Group E, F, G

Class III, Division 1 and 2

Operating Temper ature T 4

General Purpose valve for Hazardous Locations

Class I, Division 1, Group A, B, C, D

Class II, Division 1, Group E, F, G

Class III, Division 1 and 2

Operating Temper ature T 6

Intrinsically Safe Apparatus for Hazardous Locations

Class I, Division 1, Group A, B, C, D

Class II, Division 1, Group E, F, G

Class III, Division 1

Operating Temper ature T 6

FM approved as

Nonincendive for Hazardous Locations

Class I, Division 2, Group A, B, C, D

Class II, Division 2, Group F, G

Class III, Division 1 and 2

Operating Temper ature T 4

UL listed for General Purpose

CSA approved for General Purpose

See label on the valve.

Table 1 Seal Materials Seat / O-ring

Fluid Temperatures [°F] Buna “N” Ethylene FKM

NBR Propylene (EPDM)

Air Fluid Temp. + 14 to + 194 - 40 to + 266 + 14 to + 266

Ambient + 14 to + 130 + 14 to + 130 + 14 to + 130

Water Fluid Temp. + 32 to + 194 + 32 to + 212 + 32 to + 212

Ambient + 32 to + 130 + 32 to + 130 + 32 to +130

Neutral gas Fluid Temp. + 14 to + 194 - 40 to + 266 + 14 to + 266

Ambient + 14 to + 130 + 14 to + 130 + 14 to + 130

Light oil Fluid Temp. + 14 to + 194 + 14 to + 266

Ambient + 14 to + 130 + 14 to + 130

Operating Instructions 0605/09_EN-EN_00800026

Voltage 12V or 24V

UL / UR valid with

class 2 power supply only

Summary of content (2 pages)

PAGE 1
Operating Instructions Type 6017 V or 24(example): V Marking 2 ge 1 lid with Volta R vaBody nly Material y oBrass l U p / p BR = su UL Stainless Steel werSS = o p 2 Seal Material s s la Design: 2-way solenoid valve, direct acting, normally closed (Circuit function A). Seal Materials and Fluids handled: See Table 1. c Fluid and Ambient Temperature: For Hazardous Locations Div. 1 (T4 rated) Max. Ambient Temperature 104 °F (40 °C) Max.
PAGE 2
Operating Instructions For this product to be considered UL-listed and CSA approved for General Purpose and FM approved for Hazardous Locations Division 2, it must be in conjunction with the type 2509 cable plug connector (Electrically Operated Valves Parts, YSYI2). The connector and gasket must be assembled to the valve with the screw provided after the connection of the wire leads. This valve and connector assembly is delivered together and is to be used as one unit.