Ender-3 3D Printer User Manual ◆ This Manual is for the Ender-3 3D printer. ◆ Select the correct input voltage to match your local mains (230V or 115V) ◆ Because of software/hardware upgrades and model differences, new revisions may not be listed in this guide. ◆ Detailed instructions for use are available in the TF card. V.2.
Notes 1. Do not use the printer in other wrong ways to avoid personal injury or property damage. 2. Do not place the printer near any heat source or flammable or explosive objects. We suggest placing it in a well-ventilated, low-dust environment. 3. Do not expose the printer to violent vibration or any unstable environment, as this may cause poor print quality. 4. Before using experimental or exotic filaments, we suggest using standard filaments such as ABS or PLA to calibrate and test the machine. 5.
Contents 1. 2. 3. 4. Introduction ...……………………………1 Screen Information …………………………2 Loading Filament ….……………………3 Bed Levelling ..…….……………………4 5. 6. 7. 8. Software I ns tallation ..… … … … … … 5 Preparing to Print……………………6 Trouble-Sho o t i n g … … … … … … … … 7 Circuit Wiring Diagram …………………8 Preface Dear Customers: Thank you for choosing our products. For the best experience, please read the instructions before operating the Printer. Our 3D team is always ready to provide you with assistance.
1. Introdution 7 6 16 8 15 9 10 5 1. Introdution 11 4 1 1. 2. 3. 4. 1 2 Control Box TF Slot and USB Port Print Surface Control Knob 12 3 5. 6. 7. 8. Display Nozzle Assembly Spool Holder Extruder (E) Stepper 9. 10. 11. 12. 13 Power Y Limit Switch Y Stepper Coupling 14 13. 14. 15. 16.
2.
3. Loading Filament 1. Preheat Method 1 Method 2 2. Feeding Tip：Replacing the Filament 1、Cutting filament near the Extruder and slowly feed new filament until the new filament get into the PTFE tube. 2、Preheating the nozzle,Press and hold the extruder, 3 Press and hold the extruder lever then insert 1.75mm filament through the small hole of the extruder. Continue feeding until you see filament out of the nozzle. extract the filament, then feed the new filament.
4. Bed Levelling 1. Prepare →Auto Home. Wait for the nozzle to move to the left/front of the platform. 2. Prepare→Disable Steppers 4 3 1 2 3. Move the nozzle to the front/left leveling screw and adjust the platform height by turning the knob underneath. Use a piece of A4 paper (standard printer paper) to assist with the adjustment, making sure that the nozzle lightly scratches the paper. 4. Complete the adjustment on all 4 corners 5. Repeat above steps 1-2 times if necessary.
5. Software Installation 1. Double click to install the software. 2、Double click to open the software. 5 3. Select language→Next→Select your machine→Next→Finish.
6. Preparing to Print 1.Slicing Open the software→Load→Select the file→Wait for slicing to finish ,and save the gcode file to TF card. 2.Printing Insert the TF card→ Int. TF-Card → Print from TF→Select the file to be printed.
7.
8.
After- Sales Service Service 1, The printer can be returned within seven days, 15 days replacement, one year warranty, lifetime maintenance. Replacement requirement 1. The appearance of the product is intact, without damage, scratches, smudges, cracks, deformation, etc.; 2. Machine parts, tools and others are complete; 3. Provide a complete and valid purchase invoice and warranty, product number should be the same.
