Owner`s manual
Timer Setting
SWING
TIMER
When the unit is shut off, timing start can be set; After the unit is started up, timing
shutoff can be set. After the "TIMER" key is pressed, the unit enters the timing set
status and the word "TIMER" flashes on the display. Now user can press ( ) or( )
key to increase or decrease the set time. Press the "TIMER" key again and then the
timing shall go into effect. Now the unit starts to count the time passed. When the unit
is under timing status, you can cannel timing set by pressing the “TIMER” key. The
range of set time is between 0.5 to 24 hours.
Energy Saving Setting
SWING
TIMER
When the unit is shut off, press the
“FAN”
key and the ( ) simultaneously for 5
consecutive seconds to activate the energy saving setting menu.
Now
“SAVE”
and
“COOL”
are displayed (In case it is the first time to set energy saving, the initial
value shall be displayed: 26
.
The lower limit of
temperature
shall be
displayed
on
the set
temperature
and the
temperature
value under setting shall flash. Set
t
he
lower limit of cooling
temperature
using the ( ) key or the ( ) key (the lower limit
temperature
can be selected from the range between 16-30). Press
t
he
“ON/OFF”
key to confirm the setting;
Also
use the ( ) key or the ( ) key to set
t
he
upper limit
of
temperature
and the
temperature
value shall flash on the
ambient temperature
area
(OUT ENV
area) (the upper limit
temperature
can be
selected
fr
om
the range
between 16-30). Press the
“ON/OFF”
key to confirm the
se
tting.
Please pay attention
that the upper limit
temperature
must be higher than
t
he
se
t
lower limit
temperature;
Otherwise the system shall regard the higher
t
em
perature as the
upper limit
temperature
and the lower one as the lower limit
temperature.
Press
the
“MODE”
key to complete the energy saving setting
f
or
t
he
modes of cooling
and dehumidifying and turn to the energy saving setting for the heating mode
(Cooling only unit does not have this function). Now the
L
CD
displa
y
s
“
S
A
VE
”
and
“HEA
T”.
A
f
t
er
s
e
tting
is
co
m
pl
e
t
ed,
p
r
ess
t
he
“
F
AN”
key
and the ( ) key
simultaneously for 5 consecutive seconds to exit the setting of energy saving. After
the energy saving setting interface is activated, the s
y
s
t
em
shall exit the interface
if there is no any operation within 20 seconds after
t
he
last key input, and the
normal shutoff status interface shall be displayed. After the above settings are
completed, the system shall display
“SAVE”.
Now the
se
t
temperature
shall not
exceed the
temperature
range of the energy saving s
e
t
ting before. For example,
the lower cooling limit is set as 23°C and the
upper
cooling limit is set as
27°C
for
the energy saving
temperature
setting in left
so the cooling t
emper
atur
e can only
be select
ed fr
om t
he r
ange of 23 °C t
o 2
7°C
by using the remote controller or the
wire controller
lat
e
r
.
If
the upper limit
t
em
perature is the same as the lower limit
temperature,
the system can only
oper
a
t
e
at such
temperature
under relevant
modes.
R
emove
of energy saving
se
tting:
To
remove the energy saving setting
after it takes into effect, you can press
t
he
“FAN”
and the ( ) key simultaneously
for 5 consecutive seconds when the unit is shut off. But the value set before
will
not be cleared but as the initial set
t
em
pe
r
atur
e
f
or
t
he
next
ener
gy
saving
se
tting.
Af
t
er
t
he
unit
is
disconnect
ed
t
o
power suppl
y
,
the energy saving setting shall be
stored. The setting still functions
when
the unit is
connected
to power supply
again.
If
the energy saving mode is set,
t
he sleep mode and
t
he aut
o mode shall be
invalidat
ed
...