ULTRA QUIET & OIL FREE AIR COMPRESSOR OwnER'S MAnUAL 1610A 1675A 1650A 3010 WWW.CALIFORNIAAIRTOOLS.
AIR COMPRESSOR TAbLe OF CONTeNTS INTROduCTION IntroductIon __________________________________2 ImportAnt SAfety InStructIonS _______________3 LocAtIonS of ImportAnt LAbeLS _______________6 AIr compreSSor componentS__________________9 pre-operAtIon checkLISt _____________________14 package contents & Assembly___________________14 Inspect for damage ____________________________15 Save packaging _______________________________15 compressor Location __________________________15 electrical power _____________
AIR COMPRESSOR how to find a local service center: DANGER even quality built equipment might need service or repair parts. Contact the California Air Tools Customer Service department: Phone: 1-866-409-4581 Online: WWW.CALIFORNIAAIRTOOLS.COM please provide the information below: KICKBACK n Model number and Serial number and specifications shown on the Model number/Serial number plate. n Part number or numbers shown in the parts list section of the owner’s manual for your air compressor model.
AIR COMPRESSOR WARNING WARNING FLYING OBJECTS RISK TO BREATHING Dust or dust-like particulates caused by power-sanding, sawing, grinding, drilling or any other construction-like activities can contain contaminants that are harmful to breathe. Always use your air compressor in a well-ventilated and clean area. Never breathe the air that comes directly out of the air compressor or air hose. This air is not suitable for breathing. Always wear approved safety equipment.
AIR COMPRESSOR WARNING WARNING EXPLOSION EXPLOSION Improper care could lead to the air tank bursting or exploding. Drain air tank daily or after each use to prevent moisture buildup in the air tank. Rust can weaken the air tank and cause leaks or bursting. If rust is detected, replace tank immediately. Do not try to repair the air tank by welding, drilling or modifying it in any other way. These modifications can weaken the air tank and cause a hazardous condition.
AIR COMPRESSOR LOCATIONS OF IMPORTANT LAbeLS PROduCT LAbeL A Read these important labels before operating. These labels provide important safety and maintenance information. These labels should be considered as permanent parts of the air compressor. Should any of these labels become illegible, damaged or removed, please contact California Air Tools Customer Service department at 1-866-409-4581 for replacements. b model: 4620A / 4610A / 4610 c D B A E F d C e f g Note: 1.
AIR COMPRESSOR model: 6310 PROduCT LAbeL F A A C B b H c D d G e E f g Note: 1. The air compressor should only be placed in a well-ventilated and clean area. 2. Keep the air compressor on a firm and flat surface, with adequate space surrounding it for ventilation. 3. If the air compressor needs repair or becomes damaged, turn off the power and drain the tank. 4. Motors cannot be more than 10% lower or higher than the standard voltage. 5.
AIR COMPRESSOR model: 3010 PROduCT LAbeL A C b c F b A e d d H e G f model: 1610A, 1675A, 1650A A C b g Note: e 1. The air compressor should only be placed in a well-ventilated and clean area. 2. Keep the air compressor on a firm and flat surface, with adequate space surrounding it for ventilation. 3. If the air compressor needs repair or becomes damaged, turn off the power and drain the tank. 4. Motors cannot be more than 10% lower or higher than the standard voltage. 5.
AIR COMPRESSOR AIR COMPReSSOR COMPONeNTS model: 4610A 4610 74 73 no. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 description Fan Cover Fan Crank Case Connecting Rod Piston Ring Plate Pinch Pressure Plate Screw Cylinder Cylinder Obturating Ring Cylinder Head Obturating Ring Cylinder Head Cylinder Head Screw Connecting Hose Obturating Ring Connecting Hose Pan Head Screw Limited block Gassing Valve Plate Valve Plate Air Inflow Valve Plate no.
AIR COMPRESSOR model: 6310 15 16 13 17 14 12 18 19 11 20 10 21 9 37 8 7 6 5 31 30 29 28 35 4 26 3 1 38 22 25 23 24 34 39 36 27 32 2 33 41 40 42 43 44 45 46 60 59 58 57 48 49 56 50 55 51 52 54 no.
AIR COMPRESSOR model: 3010 38 15 16 12 13 17 14 18 11 37 10 19 20 9 21 8 7 6 5 32 4 31 30 29 28 3 1 26 2 25 22 23 24 27 33 34 45 35 36 53 46 43 50 40 42 51 44 48 52 41 39 49 47 60 58 59 54 55 56 57 no.
AIR COMPRESSOR model: 4620A no. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 12 description bolt Fan Cover Fan Nut Crank Case Adjustment Stent bolt Connecting Rod Pistion Ring Plate Pinch Pressure Plate Screw Cylinder Cylinder Obturating Ring Cylinder Head Obturating Ring Cylinder Head Cylinder Head Screw Spring Washer Connecting Hose Obturating Connecting Hose Pan Head Screw no.
AIR COMPRESSOR model: 1650A 1675A 1610A no. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 description Fan Cover Fan Crank Case Connecting Rod Piston Ring Plate Pinch Pressure Plate Screw Cylinder Cylinder Obturating Ring Cylinder Head Obturating Ring Cylinder Head Cylinder Head Screw Connecting Hose Obturating Connecting Hose Pan Head Screw Limited block Gassing Valve Plate Valve Plate Air Inflow Valve Plate no.
AIR COMPRESSOR PRe-OPeRATION CHeCkLIST package contents & Assembly model: 6310 model: package contents: 4620A/4610A/4610/1610A/1675/1650A n Air Compressor n Owner's Manual package contents: n Air Filter n Air Compressor n Wheel Assembly kit n Owner's Manual Assembly: n Air Filter (4620A (2) Air Filters) 1. bolt #53 (2) Assembly: n Attach the air filter to the top right side of motor head. Screw air filter into the motor head.
AIR COMPRESSOR Inspect for damage maintain a clear Area before using the air compressor, make sure the air tank is not damaged, inspect all parts for damage, and check that all pipes are firmly connected. It is very important that the air compressor is positioned so that there is adequate airflow around the machine. There must be at least 2 feet of obstacle-free space surrounding and above the air compressor. do not use the air compressor if any damage is found.
AIR COMPRESSOR OPeRATING THe AIR COMPReSSOR electrical power electrical power requirements DANGER Save this manual for future reference. SHOCK There is a danger of electric shock. Use only undamaged electrical cords. DO NOT touch bare wires or receptacles. DO NOT operate air compressor in wet weather or in wet conditions. DO NOT touch air compressor or cords if hands or feet are wet. Ensure that all cords are free of damage before connecting to the power supply.
AIR COMPRESSOR test run WARNING before using the air compressor for the first time, complete a test run as follows: 1. Turn the power switch to the OFF position. Plug the power supply cord into a power supply socket. Start the air compressor by turning the power switch to the ON position. The pressure gauge reading will slowly rise as pressure increases inside the air tank. When the gauge reading reaches 120 PSI, the pressure switch will automatically turn the power off.
AIR COMPRESSOR MAINTeNANCe draining the Air tank Adjusting the pressure Switch The frequency at which you should drain the air tank depends on the environmental conditions and the amount of operating time logged. The average draining frequency is every 2 to 3 days. The pressure switch is used to control the automatic stop-andstart function of the air compressor, ensuring the correct pressure of the compressed air in the air tank is maintained. 1.
AIR COMPRESSOR TROubLeSHOOTING probLem poSSIbLe cAuSe poSSIbLe SoLutIonS Air leaks at connections. Let the compressor build pressure in the tank, to the maximum pressure if possible. brush soapy water on air connections and look carefully for air bubbles. Tighten leaky connections. If the problem persists, contact the seller for further advice. Non-return valve seal is defective. Let the air in the tank flow out until all the pressure is released.
AIR COMPRESSOR SPeCIFICATIONS electrical circuit Pressure switch Overload protector Electric cord for motor (MAX temperature 135°C) Motor Red cords for Capacitor Solenoid valve Electric cord for motor Earth wire (Green) Air passage drawing Air intake Pressure switch Drain valve Safety valve Pressure gauge Regulator Compressor Pressure gauge Tank Filter Check valve Solenoid valve Air compressor model 4620A Ball valve 4610 / 4610A 6310 Output @ 40 PSI 7.00 CFM 3.80 CFM 3.
AIR COMPRESSOR CALIFORNIA AIR TOOLS INC. LIMITed WARRANTy This warranty is limited to Air Compressors distributed by: California Air Tools, Inc. 8560 Siempre Viva Road, unit 3A San diego, CA 92154 Limited Warranty California Air Tools Inc. will repair or replace, free of charge, to the original retail customer who purchased a California Air Tools, Inc. Air Compressor from an authorized dealer, distributor or distributor’s dealer in North America. This warranty does not transfer to subsequent owners.
AIR COMPRESSOR exclusions In addition to the foregoing disclaimers, limitations and terms, this limited warranty shall not apply to and does not cover accessories, nor does it cover products that are in any way subject to any of the following: 1. Improper setup, installation or storage. 2. Lack of proper maintenance and service. 3. Accident, damage, abuse or misuse. 4. Abnormal operating conditions or applications. 5.
AIR COMPRESSOR PROduCT ReGISTRATION To register your product, please complete the information below and mail to the mailing address at the end of this page. 1.
