Light & Quiet AiR COMPReSSOR OwneR'S MAnuAL CALiFORniA AiR tOOLS 1P1060SP .6 hP 1.60 CFM @ 40 PSi 1.20 CFM @ 90 PSi 1.0 gALLOn SteeL tAnk WWW.CALIFORNIAAIRTOOLS.
AiR COMPReSSOR TAbLe OF CONTeNTS INTROduCTION IntroductIon __________________________________2 Important Safety InStructIonS _______________3 LocatIonS of Important LabeLS _______________6 aIr compreSSor componentS__________________7 pre-operatIon checkLISt ______________________8 package contents & assembly____________________8 Inspect for damage _____________________________9 Save packaging ________________________________9 compressor Location ___________________________9 thank you for purchasing a ca
AiR COMPReSSOR how to find a local service center: even quality built equipment might need service or repair parts. Contact the California Air Tools Customer Service department: Phone: 1-866-409-4581 Online: WWW.CALIFORNIAAIRTOOLS.COM please provide the information below: Model number and Serial number and specifications shown on the Model number/Serial number plate. Part number or numbers shown in the parts list section of the owner’s manual for your air compressor model.
AiR COMPReSSOR WARNING WARNING FLYING OBJECTS RISK TO BREATHING Dust or dust-like particulates caused by power-sanding, sawing, grinding, drilling or any other construction-like activities can contain contaminants that are harmful to breathe. Always use your air compressor in a well-ventilated and clean area. Never breathe the air that comes directly out of the air compressor or air hose. This air is not suitable for breathing. Always wear approved safety equipment.
AiR COMPReSSOR WARNING WARNING EXPLOSION EXPLOSION Improper care could lead to the air tank bursting or exploding. Drain air tank daily or after each use to prevent moisture buildup in the air tank. Rust can weaken the air tank and cause leaks or bursting. If rust is detected, replace tank immediately. Do not try to repair the air tank by welding, drilling or modifying it in any other way. These modifications can weaken the air tank and cause a hazardous condition.
AiR COMPReSSOR LOCATIONS OF IMPORTANT LAbeLS PROduCT LAbeL a Read these important labels before operating. These labels provide important safety and maintenance information. These labels should be considered as permanent parts of the air compressor. Should any of these labels become illegible, damaged or removed, please contact California Air Tools Customer Service department at 1-866-409-4581 for replacements.
AiR COMPReSSOR Customer Support: 1-866-409-4581 7
AiR COMPReSSOR PRe-OPeRATION CheCkLIST package contents & assembly model: 1p1060Sp package contents: Air Compressor Owner's Manual assembly: No Assembly required for the CAT-1P1060SP Air Compressor. For hose Assembly: (Air hose not included) Attach a 1/4” universal or Industrial Male Quick Connector to an air hose. Push the 1/4” universal or Industrial Male Quick Connector (on the air hose) into the 1/4” universal or Industrial Female Quick Connector attached to the air compressor.
AiR COMPReSSOR Inspect for damage maintain a clear area before using the air compressor, make sure the air tank is not damaged, inspect all parts for damage, and check that all pipes are firmly connected. It is very important that the air compressor is positioned so that there is adequate airflow around the machine. There must be at least 2 feet of obstacle-free space surrounding and above the air compressor. do not use the air compressor if any damage is found.
AiR COMPReSSOR electrical power electrical extension cords electrical power requirements Inspect all electrical extension cords to ensure that they are free of damage. When using an extension cord, use a heavy-duty cord that is no more than 25 feet long and at least 14 gauge.use only a 3-wire extension cord that has a 3-blade grounding plug. OPeRATINg The AIR COMPReSSOR Save this manual for future reference.
AiR COMPReSSOR test run WARNING before using the air compressor for the first time, complete a test run as follows: 1. Turn the power switch to the OFF position. Plug the power supply cord into a power supply socket. Start the air compressor by turning the power switch to the ON position. The pressure gauge reading will slowly rise as pressure increases inside the air tank. When the gauge reading reaches 115 PSI - 120 PSI, the pressure switch will automatically turn the power off.
AiR COMPReSSOR MAINTeNANCe draining the air tank pressure Switch The frequency at which you should drain the air tank depends on the environmental conditions and the amount of operating time logged. The average draining frequency is every 1 to 3 days. The pressure switch is factory pre-set to shut off at between 115 - 120 PSI and to re-start at between 85 -90 PSI 1. Place the air compressor above a container capable of holding water. 2.
AiR COMPReSSOR TROubLeShOOTINg probLem Pressure drop in the tank. The unloader valve leaks when the compressor is idle. The compressor stopped and does not start. poSSIbLe cauSe poSSIbLe SoLutIonS Air leaks at connections. Let the compressor build pressure in the tank, to the maximum pressure if possible. brush soapy water on air connections and look carefully for air bubbles. Tighten leaky connections. If the problem persists, contact the seller for further advice.
AiR COMPReSSOR SPeCIFICATIONS electrical circuit Pressure switch Overload protector Electric cord for motor (MAX temperature 135°C) Motor Red cords for Capacitor Solenoid valve Electric cord for motor Earth wire (Green) air passage drawing Air intake Pressure switch Drain valve Safety valve Pressure gauge Regulator Compressor Tank Check valve Solenoid valve 14 Pressure gauge Filter Ball valve Customer Support: 1-866-409-4581
AiR COMPReSSOR CALIFORNIA AIR TOOLS INC. LIMITed WARRANTy This warranty is limited to Air Compressors distributed by: California Air Tools, Inc. 8560 Siempre Viva Road, unit 3 San diego, CA 92154 Limited Warranty California Air Tools Inc. will repair or replace, free of charge, to the original retail customer who purchased a California Air Tools, Inc. Air Compressor from an authorized dealer, distributor or distributor’s dealer in North America. This warranty does not transfer to subsequent owners.
AiR COMPReSSOR exclusions In addition to the foregoing disclaimers, limitations and terms, this limited warranty shall not apply to and does not cover accessories, nor does it cover products that are in any way subject to any of the following: 1. Improper setup, installation or storage. 2. Lack of proper maintenance and service. 3. Accident, damage, abuse or misuse. 4. Abnormal operating conditions or applications. 5.
AiR COMPReSSOR PROduCT RegISTRATION To register your product, please complete the information below and mail to the mailing address at the end of this page. 1.
