ULTRA QUIET & OIL FREE TAnk LEss AIR COMPREssOR OwnER's MAnUAL TL5 TL10 WWW.CALIFORNIAAIRTOOLS.
AIR COMPREssOR TAbLe OF CONTeNTS INTROduCTION InTroducTIon __________________________________2 ImporTanT SafeTy InSTrucTIonS _______________3 LocaTIonS of ImporTanT LabeLS _______________6 aIr compreSSor componenTS__________________7 pre-operaTIon checkLIST ______________________8 Thank you for purchasing a california air Tools, Inc. air compressor.
AIR COMPREssOR how to find a local service center: DANGER even quality built equipment might need service or repair parts. Contact the California Air Tools Customer Service department: Phone: 1-866-409-4581 Online: WWW.CALIFORNIAAIRTOOLS.COM please provide the information below: Model number and Serial number and specifications shown on the Model number/Serial number plate. Part number or numbers shown in the parts list section of the owner’s manual for your air compressor model.
AIR COMPREssOR WARNING RISK TO BREATHING Dust or dust-like particulates caused by power-sanding, sawing, grinding, drilling or any other construction-like activities can contain contaminants that are harmful to breathe. Always use your air compressor in a well-ventilated and clean area. Never breathe the air that comes directly out of the air compressor or air hose. This air is not suitable for breathing. Always wear approved safety equipment.
AIR COMPREssOR WARNING EXPLOSION Improper care could lead to the air tank bursting or exploding. Drain air tank daily or after each use to prevent moisture buildup in the air tank. Rust can weaken the air tank and cause leaks or bursting. If rust is detected, replace tank immediately. Do not try to repair the air tank by welding, drilling or modifying it in any other way. These modifications can weaken the air tank and cause a hazardous condition.
AIR COMPREssOR LOCATIONS OF IMPORTANT LAbeLS PROduCT LAbeL Read these important labels before operating. These labels provide important safety and maintenance information. These labels should be considered as permanent parts of the air compressor. Should any of these labels become illegible, damaged or removed, please contact California Air Tools Customer Service department at 1-866-409-4581 for replacements.
AIR COMPREssOR model: TL5 & TL10 no. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 description Fan Cover Fan Crank Case Connecting Rod Piston Ring Plate Pinch Pressure Plate Screw Cylinder Cylinder Obturating Ring Cylinder Head Obturating Ring Cylinder Head Cylinder Head Screw Connecting Hose Obturating ring Connecting Hose Pan Head Screw Limited block Gassing Valve Plate Valve Plate Air Inflow Valve Plate no.
AIR COMPREssOR PRe-OPeRATION CHeCkLIST Inspect for damage before using the air compressor motor inspect all parts for damage. do not use the air compressor motor if any damage is found. package contents & assembly If damaged, have an authorized service center inspect and test the air compressor motor to ensure that is working properly. model: TL5 Save packaging TL10 Save all outside packaging in case you ever need to return the product for service or repair.
AIR COMPREssOR electrical power maintain a clear area electrical power requirements It is very important that the air compressor is positioned so that there is adequate airflow around the machine. There must be at least 2 feet of obstacle-free space surrounding and above the air compressor. before using the air compressor motor, refer to the serial label for voltage and amperage requirements. Make sure you have a sufficient electrical supply for supporting the motor's requirements.
AIR COMPREssOR OPeRATING THe AIR COMPReSSOR . Test run before using the air compressor for the first time, complete a test run as follows: Plug the power cord from the air compressor into the Power Foot Pedal cord socket. Plug this cord into a power supply such as a (wall socket). Open the Air Hose outlet (air cock) by tuning the level to the forward or middle position.This will open the outlet and release the air. Start the air compressor by pressing down on the Power Foot Pedal.
AIR COMPREssOR MAINTeNANCe WARNING changing the air filter The air filter is designed to reduce noise and help prevent particulates in the air from entering and damaging the air compressor. After being used for a period of time, the air filter will become clogged. This will reduce the air intake capabilities of the air compressor, reducing performance. Therefore, the air filter must be replaced regularly. 1. Open the lid on the air filter, then remove the old filter. 2.
AIR COMPREssOR TROubLeSHOOTING probLem poSSIbLe cauSe poSSIbLe SoLuTIonS . Release the Pressure: The compressor stopped and does not start. A. Open Air Hose The pump and motor is fully pressurized b. Open Air Hose Outlet (air cock) C. Open bleeder Valve (bottom of the water trap) The motor is humming. d. Open Safety Valve Check that the main voltage corresponds to the specifications. Overloaded because of motor overheating.
AIR COMPREssOR SPeCIFICATIONS electrical circuit Pressure switch Electric cord for motor Overload protector (MAX temperature 135°C) Motor Red cords for Capacitor Solenoid valve Electric cord for motor Earth wire (Green) 13 Customer Support: 1-866-409-4581 13
AIR COMPREssOR CALIFORNIA AIR TOOLS INC. LIMITed WARRANTy This warranty is limited to Air Compressors distributed by: California Air Tools, Inc. 8560 Siempre Viva Road, unit 3A San diego, CA 92154 Limited Warranty California Air Tools Inc. will repair or replace, free of charge, to the original retail customer who purchased a California Air Tools, Inc. Air Compressor from an authorized dealer, distributor or distributor’s dealer in North America. This warranty does not transfer to subsequent owners.
AIR COMPREssOR exclusions In addition to the foregoing disclaimers, limitations and terms, this limited warranty shall not apply to and does not cover accessories, nor does it cover products that are in any way subject to any of the following: 1. Improper setup, installation or storage. 2. Lack of proper maintenance and service. 3. Accident, damage, abuse or misuse. 4. Abnormal operating conditions or applications. 5.
AIR COMPREssOR PROduCT ReGISTRATION To register your product, please complete the information below and mail to the mailing address at the end of this page. 1.
