Installation Sheet

Pg. #11
Pg. #2
INSTRUCTIONS
A ceiling fan has a completely internal switching system for total operation by
way
of pull chains. On a fan/light combination, pull chains will exist: One for light,
on
and off. The second is for fan speeds. This will be marked (SPEED) on the fan
switch housing.
1st Pull will give fan High Speed
2nd Pull will give fan Medium Speed
3rd Pull will give fan Low Speed
4th Pull will Shut Fan Off
The third pull chain is for Forward/Reverse#(Note: Some models come with a slide
switch instead of a pull chain). This setting would usually be changed twice per
year. Downdraft in summer to create a wind chill to give a cooling effect. Updraft
in winter to circulate the hot stratified air off the ceiling and back down to the floor
without creating a wind chill.
SAFETY PRECAUTIONS
1. Turn off power at main electrical service box before starting installation.
2. Electrical connections must comply with local code ordinances, national
electrical codes, CEC, NEC and ANSI/NFPA 70.
3. Make sure the installation site you choose allows the fan blades to rotate
freely without any obstructions.
4. When mounting the fan on a ceiling outlet box, Use an approved (CSA for
Canada and UL for U.S.) ceiling fan box marked "FOR FAN SUPPORT".
5. WARNING: To reduce the risk of fire, electric shock, or personal injury,
mount fan only to an outlet box marked acceptable for fan support and use
mounting screws provided with the outlet box. Most outlet boxes commonly
used for the support of lighting fixtures are not acceptable for fan support
and may need to be replaced. Consult a qualified electrician if in doubt.
Ensure the outlet box is securely installed in place such that it is able to
support at least the fan weight.
three
6.Total Fan Weight For Reference:
42"approximate 7.5 kgs(16.53lbs),
52"approximate 9.0 kgs(19.84lbs).
NOTE: Electrical diagrams are for reference only. Light kits that are not packed with the fan must be CSA/UL
Listed and marked approval for use with the model fan you are installing. Switches must be CSA/UL
General Use witches. Refer to the instructions packaged with the light kits and switches for proper
assembly.
B
PERMANENTLY ATTACHED LIGHT
- Loosen thumb screws on light.
- Install proper wattage and type
of bulb identified on light or shade.
- Place shade on light and secure
with thumb screws, finger tight.
A
DETACHABLE LIGHT KITS
- Remove 2 clips (optional) and nuts. Loosen third clip (optional) and nut.
- Place proper bulb type and wattage into the fixture.
Fig. 10m
- Align slots in glass bowl with nipples on
fixture. Slide glass into loosened clip.
Assemble the other 2 clips to the fixture
and then tighten all three nuts in place.
- Connect tassels to switches feeding
chains through nuts on light kit.
NOTE: Pull chain switches are available for some models.
- Loosen thumb screws on light.
- Place shade on light and secure with
thumb screws, finger tight.
- Connect tassels to switches feeding
chains through nuts on light kit.
Bulb
(not provided)
- To r
-
- Mount
floor or
- DO
be
chain
WARNING
educe the risk of fire or electrical shock, ONLY use model CQ005
remote control for optional remote control adaptability.
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR PERSONAL
INJURY, MOUNT TO OUTLET BOX MARKED ACCEPTABLE FOR FAN SUPPORT
AND USE MOUNTING SCREWS PROVIDED WITH THE OUTLET BOX.
with the lowest moving parts at least 2.10 Meters (7 Feet) above
grade level.
NOT operate reversing switch while fan blades are in motion. Fan must
turned off and rotating blades stopped, reverse chain pulled, the speed
pulled again to start in the opposite direction.
rews
Kit
White Wire
Screws
Thumb
Screws
Nuts
Chain
Glass Bowl
Lock washer
Fig. 10k
Red or Blue
Wires
Black or
Blue Wires
White Wire
Screws
Clips
Chain
Glass
Lock washer
Fig. 10 l
Red or Blue
Wires
Black or
Blue Wires
Nuts
WARNING: Check all connections, set screws and screws a resecu rely tightened
before the next step.
To clean the fixture, turn off the power, wait for it to cool, and wipe the fixture
with a clean, soft cloth.