Installation Sheet

5. Note: Refer to the style of
assembly that matches the style
of your fixture.
If your fixture has shades,
STYLE #1A - Place shade on
tube, then install bulb.
STYLE #1B - Install bulb, shade
then finial.
STYLE #2 - Remove spinner nut
from socket. Position glass on
lamp and secure with spinner
nut.
Note: Glass may face up or
down.
Note: If your fixture has candle-
style lights, slide the tubes over
the uplight sockets
STYLE #3 - Install proper bulb
type and wattage before
assembling the glass. Remove
ball screw from the curved stem.
Position glass on lamp with the
curved stem being inserted
through the hole in the glass.
Hand tighten the ball screw to
secure the glass in place.
STYLE #4 - Snap“pop off”head
or glass onto fixture (push, or
push and turn (it depends on the
style of your fixture).
6. If not already done,install
proper bulb type and wattage.
INSTALLATION:
C-9
10/16
CHANDELIER
Studs
Studs
“B”
“B”
“A”
1. Refer to the mounting bracket
style that matches the bracket that
is included with your fixture.
Attach the mounting bracket to
the outlet box using electrical box
screws (not included).
Style#1 - Loosen hex nut “A”and
“B”.Adjust stud so it clears the
fixture once assembled.Hold in
place with“A”and lock in place
with“B”.
Style#2 (Threaded holes)
Loosen“B”.Adjust stud to desired
length and lock in place with“B”
2. Screw lower downrod into
the fixture. Use the nut to tighten
and lock the downrod into place.
(optional)
NOTE: Determine your downrod
length. Lock in place by tightening
the set screws (optional).
3. Connect the ground wires
(bare copper or green) from your
fixture to the ground wire (bare
copper or green) or ground screw
in the electrical outlet box.
Connect the black wire (or wire
with marking) from the fixture to
the black wire in the electrical box
and connect the white wire from
the fixture to the white wire in the
electrical box.
4. Once connections of wires
are completed, carefully tuck
wires and wire nuts into the
electrical box making sure no bare
wire (on the black and white) is
visible at the wire nuts. Position
fixture over studs on mounting
bracket assembly. Secure fixture in
place with star washer(s) and cap
nut(s).
(not included)
White
Black
House
supply
Ground
wire
Fixture
Ground wire
Tel: [phone], Fax: [phone]
SAFETY PRECAUTIONS:
TOOLS AND MATERIALS REQUIRED:
Phillips
Screwdriver
Wire Cutters
Pliers Wrench
!
INSTRUCTIONS PERTAINING TO RISK OF FIRE OR INJURY TO PERSONS
READ ALL INSTRUCTIONS
IMPORTANT SAFETY
INSTRUCTIONS
SAVE THESE INSTRUCTIONS
QUESTIONS OR CONCERNS CONTACT AT:
1-800-265-1833 (English) / 1-800-567-2513 (French)
Monday through Friday 8:00 AM to 5:00 PM E.S.T.
Wiring supplies
as required by
local electrical
code
1. TURN OFF ELECTRICAL POWER BEFORE STARTING INSTALLATION OF LIGHT FIXTURE.
2. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE
BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE
HAZARDS INVOLVED.
3. CONNECT THE GROUND WIRES (BARE COPPER OR GREEN) FROM YOUR FIXTURE TO THE GROUND
WIRE (BARE COPPER OR GREEN) OR GROUND SCREW IN THE ELECTRICAL BOX.
4. TO CLEAN THE FIXTURE, TURN OFF THE POWER, WAIT FOR IT TO COOL, AND WIPE THE FIXTURE WITH A
CLEAN, SOFT CLOTH.
5. CLEAN GLASS WITH WATER ONLY.
NOTE: Product may not look exactly as shown in figures.
STYLE #1A STYLE #1B
Finial
Shade
Bulb
Tube
Bulb
Star
Washer
Cap
Nut
Stud
Downrod
Downrod
Nut
(Optional)
Wire
Fixture
Canopy
Set screw(s)
(Optional)
Fixture
Glass
Fixture
Socket
Fixture
Socket
Spinner
Nut
Glass
Hole
For Stem
Ball Screw
STYLE #2
STYLE #2
STYLE #1
STYLE #3
STYLE #4
“Pop Off”
Head or Glass